Rotabroach RHINO 4 Manual de usuario
RHINO 4
Petrol Driven Rail Drilling Machine
Model RD074
OPERATOR'S MANUAL
Approved in accordance with GM/RT1310 (Issue 2) CEF Number 12280
This machine (Serial No ) is CE approved.
IN-301-01 / RLL222
SAFETRACK BAAVHAMMAR AB
L.Moelleberga
245 93 Staffanstorp, Sweden
Tel. +46 40 44 55 51
Fax. +46 40 44 55 53
Issue 3 July 2004
- -1
CONTENTS OF THE MANUAL
Page No
[1] Specification of machine 2
[2] Safety procedures 3
[3] Cutting fluid 4
[4] Coolant inducement 4
[5] Fuelling 5
[6] Motor operating instructions 6
[7] Machine operating instructions 8
[8] Cutters for rail drilling machines 9
[9] Maintenance - general 10-11
[10] Exploded view of arbor/spindle assembly/parts list 12-13
[11] Exploded view of arbor spindle drive/parts list 14-15
[12] Exploded view of arbor spindle feed/parts list 16-17
[13] Exploded view of base plate assembly. 18-19
[14] Exploded view of clamp assembly 20-21
List of contents with drill unit Check list
RA356 Pilot (18-65 dia. Long series cutters) YES/NO
RA359 Pilot (13-18 dia. Std. series cutters) YES/NO
RA3047 Pilot (19-52 dia. std. series cutters) YES/NO
RD4088 4mm A/F Tee handled hex key YES/NO
RY2001 Coolant Feed Dispenser YES/NO
RD40038 8mm Hex key YES/NO
Issue 3 July 2004
- -2
[1] ROTABROACH RAIL DRILLING MACHINE MODEL RD074
Maximum hole cutting capacity 36mm dia.
Arbor bore 19.05mm dia. (3/4")
Engine Engine Speed
HONDA GXV50
49cm³ displacement
On load torque 3.04Nm @ 4500rpm
Fuel tank capacity 0,5 litres
No load (engine)
No load (arbor/spindle)
Normal full load (arbor/spindle)
5,000rpm
167rpm
150rpm
Compression
Ratio 8.0:1
Overall dimensions Length
Width
Height
550mm
420mm
380mm
Net Weight 18,5kgs
Maximum hand/arm vibration magnitude
(measured at handle during operation in
accordance with ISO5349)
3.8 m/s²
Estimate of likely daily vibration exposure –
Operation on 2 rails (24 holes @ 1
minute/hole)
0.85 m/s² A(8)
Average noise level during cutting at
operator’s ear position.
81 dB(A)
Approved in accordance with GM/RT1310 (Issue 2) CEF Number 12280
Must only be used in a Green Zone.
Must NOT be used on live conductor rail.
EAR DEFENDERS MUST BE WORN WITHIN 3 METRES
WHEN THE MOTOR IS RUNNING.
ANY UNAUTHORISED MODIFICATIONS TO THIS MACHINE WILL INVALIDATE
THE GUARANTEE
Issue 3 July 2004
- -3
[2] SAFETY PROCEDURES
READ BEFORE USING THE MACHINE
•ALWAYS WEAR SAFETY GOGGLES AND EAR DEFENDERS WHEN
OPERATING THE MACHINE.
•Ensure motor is switched off when changing cutters, working on the machine, or
removing swarf.
•Always ensure the cutter is securely fastened.
•Remove tie, rings, watches and loose adornments, which might entangle with the rotating
machinery.
•Should the cutter become fast in the workpiece, switch off the motor immediately to
prevent personal injury. Do not attempt to free the cutter by starting and stopping the
motor.
•If the machine is accidentally dropped, always thoroughly examine the machine for signs
of damage and check that it functions correctly before trying to cut a hole.
•Regularly inspect the machine and check that nuts and screws are tight.
•Before fuelling the tank, read section 5 (fuelling)
•Observe local and national Health & Safety requirements before operating the machine.
•Never leave the machine lying on its side. The motor sump oil may be lost at an
inclination greater than 20˚from the vertical. If this may have happened, check the sump
oil level before starting the engine.
•Always wear approved eye and ear protection when the equipment is in operation.
Failure to do so may result in personal injury.
•On completion of the cut, a slug will be ejected. DO NOT operate the machine if the
ejected slug may cause injury.
Issue 3 July 2004
- -4
[3] ROTABROACH CUTTING FLUID
•Rotabroach cutting fluid has been specifically formulated to significantly enhance the
performance and life of the cutting tool, and improve the quality and surface finish of the
hole.
•Avialable in
1 litre (RD208)
5 litre (RD229)
25 litre (RD220)
[4] COOLANT INDUCEMENT
•Constituent items:
Coolant bottle and hose assembly RY2001
Issue 3 July 2004
- -5
[5] FUELLING
Warning
Petrol is an extremely flammable fuel.
Use extreme caution when handling petrol or fuel mix.
Do not smoke or bring any fire or flame near the fuel.
Ensure the fuel mix does not spill on to hot engine.
FUELLING INSTRUCTIONS
•Fuel your machine in a well-ventilated area, outdoors only.
•Avoid direct contact with the skin and avoid inhaling fuel vapour
•Always shut off the engine and allow it to cool before refuelling.
•Before fuelling, clean the filler cap and the area around it to ensure that no dirt falls into
the tank.
•Petrol vapour pressure may build up inside the gas tank. In order to reduce the risk of
burns or other personal injury from escaping gas vapour and fumes, remove the gas cap
carefully so as to allow any pressure build-up in the tank to release slowly. Never
remove the fuel filler cap whilst the engine is running,
FUEL
•It is recommended that you always use unleaded petrol with a minimum octane number of
90 ROZ(USA)/Canada: pump octane min. 87.
•Inferior quality petrol may damage the engine, sealing rings, fuel lines or fuel tank.
Issue 3 July 2004
- -6
[6] MOTOR OPERATING INSTRUCTIONS
STARTING
•Observe safety precautions (see Section 2 – Safety Procedures)
•Ensure that the sump oil level is to the correct level.
•Ensure the machine is clamped firmly in position on the rail.
•Ensure on/off switch (RD4748) is set to 1.
•Unscrew petrol tank vent screw.
•If the motor is cold, position cold start indicator to 1 o 1.
Issue 3 July 2004
- -7
•Rotate the fuel cut off valve to the horizontal position.
•Position the cutter feed handle to the forward position.
•Repeatedly pull the engine start cord with a quick, progressive movement until the engine
starts, then release the cord handle.
•When the engine has reached it’s operating temperature, the cold start lever can be moved
from the cold start position.
•Moving the cutter feed handle anti-clockwise will increase the engine speed and feed the
cutter into the rail.
Issue 3 July 2004
- -8
[7] MACHINE OPERATING INSTRUCTIONS
•Keep the inside of the cutter clear of swarf. It restricts the operating depth of the cutter.
•Pressurise the coolant dispenser by pumping the handle until the relief valve extends and
then give a further 5 to 10 pumps of the handle.
•With the pressurised cutting fluid dispenser connected to the coolant feed tube, coolant is
“metered” out by the pilot and is applied directly to the cutting edge.
•To ensure cutting fluid is being correctly metered, depress the pilot by slowly moving the
cutter to touch the rail. Regulate the flow by adjusting the needle valve RD4217.
•As the cutter approaches the rail, the automatic throttle will increase the engine speed to
ensure maximum speed before cutting the hole. Once drilling is complete immediately
fully retract the cutter, this will return the machine to idle speed. DO NOT ALLOW
THE MACHINE TO RUN AT FULL SPEED IF NOT DRILLING.
•When commencing to cut a hole apply light pressure until the cutter is introduced into the
work surface. Pressure can then be increased slightly whilst cutting the hole. Excessive
pressure is undesirable when using the Rotabroach system, it does not necessarily
increase the speed of penetration and it may damage the cutter, greatly reducing its life.
•Cutter breakage is usually caused by insecure clamping.
Issue 3 July 2004
- -9
[8] ROTABROACH CUTTERS FOR RAIL DRILLING MACHINES
All cutters have a 3/4" dia. shank.
ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF
Take the chosen cutter and insert into its shank the appropriate pilot. Place the assembly,
correctly aligning the drive flats, into the arbor bore and securely fasten the socket screws
with the hexagon key.
RCV SERIES
(High wear)
CRWC SERIES
(Carbide Tipped)
Dia. mm Part No Pilot No Part No Pilot No
18 RCV180 RA359 CRWC18 RA3047
19 RCV190 RA3047 CRWC19 RA3047
20 RCV200 RA3047 CRWC20 RA3047
21 RCV210 RA3047 CRWC21 RA3047
22 RCV220 RA3047 CRWC22 RA3047
23 RCV230 RA3047 CRWC23 RA3047
24 RCV240 RA3047 CRWC24 RA3047
25 RCV250 RA3047 CRWC25 RA3047
26 RCV260 RA3047 CRWC26 RA3047
27 RCV270 RA3047 CRWC27 RA3047
28 RCV280 RA3047 CRWC28 RA3047
29 RCV290 RA3047 CRWC29 RA3047
30 RCV300 RA3047 CRWC30 RA3047
31 RCV310 RA3047 CRWC31 RA3047
32 RCV320 RA3047 CRWC32 RA3047
33 RCV330 RA3047 CRWC33 RA3047
34 RCV340 RA3047 CRWC34 RA3047
35 RCV350 RA3047 CRWC35 RA3047
36 RCV360 RA3047 CRWC36 RA3047
WHEN ORDERING CUTTERS AND PILOTS ALWAYS QUOTE SERIES TYPE
AND PART NUMBER
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Perforar de Rotabroach
Rotabroach
Rotabroach SMARTPUMA1 Manual de usuario
Rotabroach
Rotabroach CM/500/1 Manual de usuario
Rotabroach
Rotabroach ELEMENT 50 AUTO Manual de usuario
Rotabroach
Rotabroach SMARTPUMA1 Instrucciones de operación
Rotabroach
Rotabroach COMMANDO 40 Manual de usuario
Rotabroach
Rotabroach Cobra CM/200/1 Manual de usuario
Rotabroach
Rotabroach CM/330C Manual de usuario
Rotabroach
Rotabroach Element 100 Series Manual de usuario
Rotabroach
Rotabroach Element 50PM Manual de usuario
Rotabroach
Rotabroach RD140 Manual de usuario
Rotabroach
Rotabroach ELEMENT 50 LOW PROFILE 1 Manual de usuario
Rotabroach
Rotabroach RD130C Manual de usuario
Rotabroach
Rotabroach Element75 Manual de usuario
Rotabroach
Rotabroach Element 40 PERM Manual de usuario
Rotabroach
Rotabroach Element30/3 Manual de usuario
Rotabroach
Rotabroach Element 75 Manual de usuario
Rotabroach
Rotabroach SMARTPANTHER1 Manual de usuario
Rotabroach
Rotabroach COMMANDO40/3 Manual de usuario
Rotabroach
Rotabroach Falcon RP05520/4 Manual de usuario
Rotabroach
Rotabroach CM/705/1A Manual de usuario
