Rosewill RC205 Manual de usuario

SATA-150 1-Int/1-Ext Port PCI Adapter RC205

User Manual

SATA-150 1-Int/1-Ext Port PCI Adapter RC205

This Manual for the Models of 2 Channels SATA HBA:

Model A: Low Proﬁle Serial ATA Internal 2 Ports

Model B: Low Proﬁle External 1 Port + Internal 1 Port

Model C: Low Proﬁle Internal 1 Port + External 1 Port + Bracket Power

Model D: External 2 Ports + Bracket Power

1. Introduction

The Low Proﬁle Serial ATA 2 Channels PCI Host Adapter is a PCI to dual Serial ATA host controller

board which can support Low proﬁle PCI and regular size PCI both. It provides a 32bit, 33/66

MHz PCI interface on the host side and dual, fully compliant Serial ATA ports on the device side

to access SATA storage media such as hard disk drive, ZIP drive, CD-ROM, CD-RW, DVD-ROM.

The board can be used to upgrade your desktop computer to have dual Serial ATA Channels. It

accepts host commands through the PCI bus, processes them and transfers data between the

host and Serial ATA devices. The board should be connected to SATA target device and will take

the data, serialize it and output it for transmission over the SATA interface. The board can control

two independent Serial ATA channels. Each channel has its own Serial ATA bus and will support

one Serial ATA device.

The board supports a 32-bit 33/66 MHz PCI bus revision 2.2 and the Serial ATA Generation 1

transfer rate of 1.5 Gb/s (150 MB/s).

It comes completely with drivers for Windows 98, Windows Millennium, Windows NT 4.0,

Windows 2000 and XP.

1.1. Features

1.1.1. PCI Interface

• Compliant with PCI Speciﬁcation, revision 2.2.

• Integrated PCI DMA engines.

• 32 bit, 33/66MHz fully compliant PCI host interface.

1.1.2. High Speed Serial ATA Interface

• Dual high speed Serial ATA interface Channels, each supporting

User Manual

SATA-150 1-Int/1-Ext Port PCI Adapter RC205

1st generation Serial ATA data rates. (1.5Gb/s)

• Fully compliant with Serial ATA 1.0 speciﬁcations.

• Supports Spread Spectrum in receiver.

• Independent 256-byte FIFOs (32 bit * 64 deep) per Serial

ATA channel for host reads and writes.

1.1.3. The Individual features for different Models

1.1.3.1. Model A: Serial ATA Internal 2 Ports

• Supports Independent two Internal Ports.

1.1.3.2. Model B: External 1 Port + Internal 1 Port

• Supports one External Port and one Internal Port.

• One Special Shell SATA connector on External Port to support Mobile

HDD, Mobile CD-ROM, Mobile DVD and Mobile CD-RW.

1.1.3.3. Model C: Internal 1 Port + External 1 Port + Bracket Power

• Independent one Internal SATA Ports.

• One External Port and one Internal Port sharing one SATA Channel.

• One Special Shell SATA connector on External Port to support Mobile

HDD, Mobile CD-ROM, Mobile DVD and Mobile CD-RW.

• One USB-like Connector on board to provide 2A/5V DC

power output for Mobile Storage Devices using.

1.1.3.4. Model D: External 2 Ports + Bracket Power

• Independent two External SATA Ports.

• Two Special Shell SATA connector on External Port to support Mobile

HDD, Mobile CD-ROM, Mobile DVD and Mobile CD-RW.

• One USB-like Connector on board to provide 2A/5V DC

power output for Mobile Storage Devices using.

1.2. Package Contents

• Low Proﬁle Serial ATA 2 Channel PCI Host Adapter

• This Users Manual

• Driver Diskette

• Low Proﬁle Size PCI Bracket ( Not supported on Model D)

2. Software Installation

This section provides the information on how to install the drivers of Low Proﬁle Serial ATA 2 Port

User Manual

SATA-150 1-Int/1-Ext Port PCI Adapter RC205

PCI Host Adapter for the operating systems:

New & Existing Windows 98/98 SE

New & Existing Windows ME

New & Existing Windows NT 4.0

New & Existing Windows 2000

New & Existing Windows XP

2.1. Windows 98/98SE Driver Installation

For New Windows 98/98 SE Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, follow Microsoft

procedures to install Windows accordingly.

2. Once Windows has been installed, double click My Computer/Control Panel/System, then click

Device Manager.

3. Double click Other Devices then PCI RAID Controller.

4. Click Driver tab, then Update Driver.

5. Insert the Driver diskette and click Next.

6. Select Search for a better driver than the one ...option and click Next.

7. Check Specify a location, uncheck the other boxes, type in A:\ and click Next. Click Next and

then Finish.

8. Remove the Driver diskette and click Yes to restart Windows to complete driver installation.

For Existing Windows 98/98 SE Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, boot up Windows.

2. At the Add New Hardware Wizard, click Next.

3. Select Search for the best driver for your device option and then click Next.

4. Insert the Driver diskette, check Specify a location, uncheck the other boxes, type in A:\, and

click Next.

5. Click Next and then Finish respectively.

6. Remove the Driver diskette and restart Windows to complete driver installation.

2.2. Windows ME Driver Installation

For New Windows ME Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, follow Microsoft

procedures to install Windows accordingly.

2. Once Windows has been installed, click My Computer, then click Properties. Click Device

User Manual

SATA-150 1-Int/1-Ext Port PCI Adapter RC205

Manager tab.

3. Double click Other Devices then PCI RAID Controller.

4. Click Driver tab, then Update Driver.

5. Insert the Driver diskette, check Specify the location of the driver (advanced) and click Next.

6. Select Search for the better driver option, check Specify a location, uncheck Removable

Media, type in A:\, and click Next.

7. Click Next and then Finish.

8. Remove the Driver diskette and click Yes to restart Windows to complete driver installation.

For Existing Windows ME Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, boot up Windows.

2. At the Add New Hardware Wizard, check Specify the location of the driver (advanced), and

click Next.

3. Insert the Driver diskette, check Specify a location, uncheck the other boxes, type in A:\, and

click Next.

4. Click Next and then Finish.

5. Remove the Driver diskette and restart Windows to complete driver installation.

Veriﬁcation of the Proper Installation for Windows 98/98SE/ME

1. Double click My Computer/Control Panel/System. Click Device Manager tab.

2. Double click SCSI Controllers, Silicon Image Sil-3112 Serial ATA Controller should be listed.

3. Highlight Silicon Image Sil-3112 Serial ATA Controller and click Properties. A message This

device is working properly is displayed in the dialog box, the driver has been correctly installed.

If any error message is displayed, remove Silicon Image Sil-3112 Serial ATA Controller and restart

your system.

2.3. Windows NT 4.0 Driver Installation

For New Windows NT 4.0 System

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, follow Microsoft

procedures to install Windows accordingly.

2. At the Windows Set-up screen, press F6 to specify and add the driver.

3. Press S, select Other, then press Enter.

4. Insert the Driver diskette and press Enter.

5. Select Silicon Image Sil-3112 Serial ATA Controller Driver and press Enter.

6. Press Enter to continue and follow on-screen instructions to complete Windows NT 4.0

installation.

For Existing Windows NT 4.0 (in old ATA channel) System

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, boot up Windows.

User Manual

SATA-150 1-Int/1-Ext Port PCI Adapter RC205

Double click My Computer/Control Panel/SCSI Adapters, then click the Drivers tab.

2. Click Add… then Have Disk....

3. Insert the Driver diskette into the ﬂoppy drive and type in A:\, then click OK.

4. Highlight Silicon Image Sil-3112 Serial ATA Controller and click OK.

5. Remove the Driver diskette and restart Windows.

Veriﬁcation of the Proper Installation for Windows NT 4.0

1. Double click My Computer/Control Panel/SCSI Adapters.

2. Highlight Silicon Image Sil-3112 Serial ATA Controller and click Properties. This device is

working properly is displayed in the dialog box, the driver has been correctly installed.

2.4. Windows 2000 Driver Installation

For New Windows 2000 Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, follow Microsoft

procedures to install Windows accordingly.

2. At the Windows Set-up screen, press F6 to specify and add the driver.

3. Insert the Driver diskette. Press S, then press Enter.

4. Select Silicon Image Sil-3112 Serial ATA Controller Driver and press Enter.

5. Press Enter to continue and follow on-screen instructions to complete installation.

For Existing Windows 2000 (in old ATA channel) Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, boot up Windows.

2. At the Found New Hardware Wizard, click Next.

3. Select Search for a suitable driver for my device (recommended) and click Next.

4. Insert the Driver diskette into the ﬂoppy drive, check Specify a location, uncheck the other

boxes, click Next, type in A:\. Click OK and then Next to continue.

5. If the Digital Signature Not Found message appears, click Yes. (Note If prompted for Windows

2000 CD-ROM, insert the CD and click OK. Type in D:\I386, click OK and Finish. (assuming D: is

your CD-ROM drive))

6. Click Finish, remove the Driver diskette and click Yes to restart Windows to complete driver

installation.

2.5. Windows XP Driver Installation

For New Windows XP Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, follow Microsoft

procedures to install Windows accordingly.

2. At the Windows Set-up screen, press F6 in order to specify and add the driver.

3. Insert the Driver diskette. Press S then press Enter.

4. Select Silicon Image Sil-3112 Serial ATA Controller Driver and press Enter.

5. Press Enter to continue and follow on-screen instructions to complete Windows XP installation.

Note: When the Software Installation warning pops up, click Yes. And when the Hardware

User Manual

SATA-150 1-Int/1-Ext Port PCI Adapter RC205

Installation warning pops up, click Yes again.

For Existing Windows XP (in old ATA channel) Systems

1. After the Serial ATA PCI Host Adapter and attached drives are conﬁgured, boot up Windows.

2. At the Found New Hardware Wizard, check Install from a list or speciﬁc location (advanced),

then click Next.

3. Insert the Driver diskette. Check Include this location in the search, uncheck the other box,

type in A:\, and click Next.

4. When a warning message pops up, click Continue Anyway, then click Finish.

5. Remove the Driver diskette and restart Windows.

Veriﬁcation of the Proper Installation for Windows 2000/XP

1. Double click My Computer/Control Panel/System.

2. Click Hardware then click Device Manager.

3. Double click SCSI and RAID Controllers, then double click Silicon Image Sil-3112 Serial ATA

Controller to display driver properties.

4. A message This device is working properly is displayed in the dialog box, the driver has been

correctly installed.

Thank you for purchasing Rosewill Product.

Please register your product at www.rosewill.com for complete warranty information and future

support for your product.

Tabla de contenidos

Otros manuales de Tarjeta PCI de Rosewill

Rosewill

Rosewill RC501 Manual de usuario

Rosewill

Rosewill RC-302E Manual de usuario

Rosewill

Rosewill RC302 Manual de usuario

Rosewill

Rosewill SATA 150 RAID 2 Port PCI Host RC201 Manual de usuario

Rosewill

Rosewill RC304 Manual de usuario

Rosewill

Rosewill RC-302 Manual de usuario

Rosewill

Rosewill RC-213 Manual de usuario

Rosewill

Rosewill RNWD?N9003PCE Manual de usuario

Rosewill

Rosewill RC-301EU Manual de usuario

Rosewill

Rosewill RNWD?N9003PCE Manual de usuario

Rosewill

Rosewill RNX-N250PC2 Manual de usuario

Rosewill

Rosewill RC303 Manual de usuario

Rosewill

Rosewill RC-305 Manual de usuario

Rosewill

Rosewill RC-301 Manual de usuario

Rosewill

Rosewill RC214 Manual de usuario

Rosewill

Rosewill RC-223 Manual de usuario

Rosewill

Rosewill RC-20002 Manual de usuario

Rosewill

Rosewill RC-303 Manual de usuario

Rosewill

Rosewill RC-20003 Manual de usuario

Rosewill

Rosewill RC-305E Manual de usuario

Rosewill

Rosewill RNX-N300X Manual de usuario

Rosewill

Rosewill RNX-N300 Manual de usuario

Rosewill

Rosewill RC-101 Manual de usuario

Rosewill

Rosewill RNX-N150PCe Manual de usuario

Manuales populares de Tarjeta PCI de otras marcas

ERMA

ERMA SSI 1417 Manual de usuario

SIIG

SIIG CyberSerial Dual PCI Instrucciones de montaje

Moxa Technologies

Moxa Technologies CP-102E Manual de usuario

I-Bus

I-Bus IBC2602 Manual de usuario

Exsys

Exsys EX-60102 Manual de usuario

Chelsio Communications

Chelsio Communications T5 Series Manual de usuario

Conrad Electronic

Conrad Electronic 97 46 71 Manual de usuario

Micro Innovations

Micro Innovations USB650A Manual de usuario

KTI Networks

KTI Networks KF-310 Manual de usuario

Asus

Asus SpaceLink WL230 Manual de usuario

SIIG

SIIG SC2475 Manual de usuario

TRENDnet

TRENDnet TEW-703PI Manual de usuario

Belkin

Belkin F5D7000F Manual de usuario

Pericom

Pericom PI7C7100 Manual de usuario

ADLINK Technology

ADLINK Technology cPCI-3548 Manual de usuario

Digium

Digium TE200 Series Manual de usuario

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manual de usuario

Western Digital

Western Digital FireWire PCI Adapter Manual de usuario