Rosen 7002 Manual de usuario
Document Number 100923 Rev D
ELECTRONIC REVISION
CONTROLLED
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 2 of 21
Technical Manual, 7002 Series WideScreen
© 2008 by Rosen Aviation, LLC
All Rights Reserved
The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written authorization from Rosen Aviation, LLC,
except as allowed under copyright laws.
Disclaimer of Liability
The information contained in this document is subject to change without notice. Because we are
continuously improving and adding features to our products, Rosen Aviation, LLC reserves the right
to change specifications without prior notice. Rosen Aviation, LLC shall not be liable for technical or
editorial errors or omissions contained herein.
Rosen Aviation, LLC
1020 Owen Loop South
Eugene, OR 97402
541.342.3802
888.668.4955
Fax: 541.342.4912
www.rosenaviation.com
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 3 of 21
Contents
1. INTRODUCTION.................................................................................................................4
1.1. Unpacking.....................................................................................................................4
2. DISPLAY CONNECTIONS .................................................................................................4
2.1. Connection Diagram.....................................................................................................5
3. INSTALLATION GUIDELINES ...........................................................................................5
3.1. Installing/Removing SlimLine Arm Assemblies.............................................................6
4. FRONT PANEL BUTTONS.................................................................................................6
4.1. Navigational Soft Keys..................................................................................................7
4.1.1. Source Select......................................................................................................................7
4.1.2. Scale ...................................................................................................................................7
4.1.3. Backlight Brightness..........................................................................................................10
4.1.4. Contrast.............................................................................................................................10
4.2. On-Screen Menus.......................................................................................................11
4.2.1. Image Adjustments Menu..................................................................................................11
4.2.2. Advanced Menu ................................................................................................................13
5. MAINTENANCE: TENSION ADJUSTMENTS ..................................................................17
6. TECHNICAL REFERENCES AND SUPPORT .................................................................18
6.1. Troubleshooting..........................................................................................................18
6.2. DO-160E Qualifications ..............................................................................................19
6.3. Technical Support.......................................................................................................20
6.4. Specifications..............................................................................................................20
7. DEFINITIONS....................................................................................................................20
8. REVISION HISTORY ........................................................................................................21
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 4 of 21
1. INTRODUCTION
This manual describes how to install the Rosen 7” WideScreen 7002 series display onto your
aircraft. It contains everything you need to know to wire the display and confirm that it is functioning
correctly.
Note: Only trained and qualified personnel should perform installation and service.
1.1. Unpacking
The parts shipped with the 7” WideScreen 7002 series display
zOutline and Installation Drawing 7002 – specific to each display/arm combination
z7002 display with arm
zDisplay Manuals CD, (P/N 9003678)
z7” WideScreen 7002 User’s Guide – (P/N 101327) – leave in the plane
The Outline & Installation drawings—specific to each
display/arm combination —are also available at
www.rosenaviation.com.
From the Rosen Aviation home page, select SupportÆDrawings and Pinouts, and search for
the drawing by model number or browsing by product category.
2. DISPLAY CONNECTIONS
There are several ways to connect the 7002 series display to an aircraft’s data systems.
Use the following pinout descriptions on page 2 of the Outline and Installation drawing to assist in
the wiring process. Pay close attention to the pinout information while completing wiring
connections.
Note: This display is for entertainment purposes only; connect to the non-critical power bus.
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 5 of 21
2.1. Connection Diagram
The typical installation of the 7” WideScreen monitor is one or more monitors on an arm mount,
sidewall, or bulkhead. The following connection diagram illustrates how to configure the displays
to create a complete cabin entertainment system or integrate a display into an existing system.
Figure 1 Typical arm mount installation
These displays are typically connected to a video distribution unit, which provides a single
composite video signal to each monitor. The video distribution box performs the source
selection.
3. INSTALLATION GUIDELINES
Ensure that when plugging the arm into the base receptacle, the set screw in the base follows the
arm’s keyed slot and the connection is not forced.
Figure 2 Arm mount base receptacle
Slot
Set screw
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 6 of 21
3.1. Installing/Removing SlimLine Arm Assemblies
To install or remove a SlimLine arm assembly, press in the arm button all the way.
Figure 3 SlimLine locking arm feature
To release a SlimLine locking arm so that it rotates, press in the arm button only half way.
4. FRONT PANEL BUTTONS
The 7002 series display has buttons on the front panel as its only control method.
Figure 4 7002 button layout
Table 1 7002 front panel buttons
Button How it Works
Power On/Off Turns the power on and off to the display. The LED indicator is red when the
power is off, and green when the power is on. Previously adjusted settings of
brightness and scaling mode are retained in memory when power is turned off,
or when aircraft power is removed.
Menu Opens a submenu of options to access other settings and fine-tune the
display’s picture quality. For details about the on-screen menus, see section
4.2.
Contrast Adjusts the LCD contrast. See section 4.1.4 for details.
Backlight Brightness Adjusts the backlight brightness. If the button is held down for more than one
second the brightness will continue to step up or down in ¼-second intervals.
See section 4.1.3 for details.
Scale Four scaling modes: Normal, Wide, Full, and Cinema allow adjustment of the
picture expansion that most closely matches the encoding of the source
image. See section 4.1.2 for details.
Source Select Changes between two composite video sources (NTSC, PAL, SECAM), which
are customer configurable. Press this button to switch sources.
Arm button
Power On/Off
Power
LED
Menu
Contrast
Backlight
Brightness
Scale
Source
Select
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 7 of 21
4.1. Navigational Soft Keys
The icons on the display buttons indicate basic functions. In addition to the basic functions, the
buttons act as soft keys that perform secondary navigational functions to adjust picture quality in
dialog boxes and the on-screen menus. When you press a button and see a bar of blue soft
keys, as shown below, press the corresponding display button.
Figure 5 Soft key buttons
Note: Before changing the display settings, try both default color modes first to determine
which set of default colors you like best. See Restore Factory Defaults on page 14 for
more information.
4.1.1. Source Select
Switch input sources by pressing the Source Select button (shown below). You will hear
a relay click, which indicates the source changed.
Figure 6 Source select button
4.1.2. Scale
Change the scaling mode by pressing the Scale button (shown below). Press the ◄or
the ►soft key to switch the display between the different scaling modes (described
below). Highlight the optimal mode for the image source and press Set to set the scaling
mode and exit the dialog box.
Æ
Figure 7 Scale button, settings, and soft keys
The label of the
menu soft key
changes
depending on
the function it is
performing
Basic
function
buttons
Secondary
soft keys
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 8 of 21
Normal Mode
Normal mode displays a standard 4:3 aspect video without alteration. A standard 4:3
source image will appear with vertical black bars on the left and right side of the screen,
as shown in Figure 8. If the image source is letterboxed, then there will be horizontal bars
at the top and bottom of the image as well.
Figure 8 Standard 4:3 aspect test pattern in Normal Mode
Widescreen 16:9 images will appear horizontally compressed with vertical black bars on
the left and right side of the screen, as shown in Figure 9.
Figure 9 Widescreen 16:9 aspect test pattern in Normal Mode
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 9 of 21
Wide Mode
Wide mode displays a standard 4:3 source video in 16:9 aspect ratio by expanding the
image horizontally. The expansion maintains normal aspect in the center region while
stretching the rest of the image to fill the screen, as shown in Figure 10.
Widescreen 16:9 will be displayed full screen with minor central compression, as shown
in Figure 11. If the source image is letterboxed, there will be black bars at the top and
bottom of the image.
Figure 10 Standard 4:3 aspect test pattern in Wide Mode
Figure 11 Widescreen 16:9 aspect test pattern in Wide Mode
Full Mode
Displays standard 4:3 source video in 16:9 aspect ratio by expanding the entire image
horizontally, as shown in Figure 12. If the source image is letterboxed, there will be black
bars at the top and bottom of the image only. Widescreen 16:9 will be displayed full
screen without distortion.
Figure 12 Standard 4:3 aspect test pattern in Full Mode
Rosen Aviation
Document Number: 100923 Revision: D
Date: 6/8/09
Template: 4.2.3-6-FM; Revision A; 16 May, 2005 Page 10 of 21
Cinema Mode
Cinema Mode expands the source video in the vertical and horizontal dimensions to fill
the display screen, as shown in Figure 13. Letterbox format DVD disks will have little or
no bars showing in this mode, while 4:3 & 16:9 aspect video sources will be expanded
beyond the boundaries of the screen, appearing cropped.
Figure 13 4:3 and 16:9 aspect test patterns in Cinema Mode
4.1.3. Backlight Brightness
Adjust the LED backlight brightness by pressing the Backlight Brightness button
(shown below). Press the ◄or the ►soft key to decrease or increase the image on the
LCD. Press the Set soft key to set the brightness and exit the dialog box.
Æ
Figure 14 Backlight brightness button, settings, and soft keys
4.1.4. Contrast
Adjust the contrast by pressing the Contrast button (shown below). Press the ◄or the
►soft key to raise or lower the contrast. Press the Set soft key to set the contrast and
exit the dialog box.
Æ
Figure 15 Contrast button, settings, and soft keys
Tabla de contenidos
Otros manuales de Monitor de Rosen
