Rosemount 700XA Manual de usuario
Quick Start Guide
00825-0100-3770, Rev AA
July 2020
Rosemount™ 700XA
Gas Chromatograph
Notice
EMERSON (“SELLER”) SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS IN THIS MANUAL OR OMISSIONS FROM THIS
MANUAL. SELLER MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THIS MANUAL AND, IN NO EVENT, SHALL
SELLER BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PRODUCTION,
LOSS OF PROFITS, ETC.
PRODUCT NAMES USED HEREIN ARE FOR MANUFACTURER OR SUPPLIER IDENTIFICATION ONLY AND MAY BE TRADEMARKS/
REGISTERED TRADEMARKS OF THESE COMPANIES.
THE CONTENTS OF THIS PUBLICATION ARE PRESENTED FOR INFORMATIONAL PURPOSES ONLY AND, WHILE EVERY EFFORT HAS
BEEN MADE TO ENSURE THEIR ACCURACY, THEY ARE NOT TO BE CONSTRUED AS WARRANTIES OR GUARANTEES, EXPRESSED OR
IMPLIED, REGARDING THE PRODUCTS OR SERVICES DESCRIBED HEREIN OR THEIR USE OR APPLICABILITY. WE RESERVE THE RIGHT
TO MODIFY OR IMPROVE THE DESIGNS OR SPECIFICATIONS OF SUCH PRODUCTS AT ANY TIME.
SELLER DOES NOT ASSUME RESPONSIBILITY FOR THE SELECTION, USE, OR MAINTENANCE OF ANY PRODUCT. RESPONSIBILITY FOR
PROPER SELECTION, USE, AND MAINTENANCE OF ANY SELLER PRODUCT REMAINS SOLELY WITH THE PURCHASER AND END-USER.
Warranty
1. LIMITED WARRANTY: Subject to the limitations contained in Section 2 herein and except as otherwise expressly provided
herein, Emerson (“Seller”) warrants that the firmware will execute the programming instructions provided by Seller and
that the Goods manufactured or Services provided by Seller will be free from defects in materials or workmanship under
normal use and care until the expiration of the applicable warranty period. Goods are warranted for twelve (12) months
from the date of initial installation or eighteen (18) months from the date of shipment by Seller, whichever period expires
first. Consumables and Services are warranted for a period of 90 days from the date of shipment or completion of the
Services. Products purchased by Seller from a third party for resale to Buyer (“Resale Products”) shall carry only the
warranty extended by the original manufacturer. Buyer agrees that Seller has no liability for Resale Products beyond
making a reasonable commercial effort to arrange for procurement and shipping of the Resale Products. If Buyer
discovers any warranty defects and notifies Seller thereof in writing during the applicable warranty period, Seller shall, at
its option, promptly correct any errors that are found by Seller in the firmware or Services, or repair or replace F.O.B. point
of manufacture that portion of the Goods or firmware found by Seller to be defective, or refund the purchase price of the
defective portion of the Goods/Services. All replacements or repairs necessitated by inadequate maintenance, normal
wear and usage, unsuitable power sources, unsuitable environmental conditions, accident, misuse, improper installation,
modification, repair, storage or handling, or any other cause not the fault of Seller are not covered by this limited
warranty, and shall be at Buyer's expense. Seller shall not be obligated to pay any costs or charges incurred by Buyer or any
other party except as may be agreed upon in writing in advance by an authorized Seller representative. All costs of
dismantling, reinstallation and freight, and the time and expenses of Seller's personnel for site travel and diagnosis under
this warranty clause shall be borne by Buyer unless accepted in writing by Seller. Goods repaired and parts replaced during
the warranty period shall be in warranty for the remainder of the original warranty period or ninety (90) days, whichever is
longer. This limited warranty is the only warranty made by Seller and can be amended only in a writing signed by an
authorized representative of Seller. Except as otherwise expressly provided in the Agreement, THERE ARE NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND, EXPRESSED OR IMPLIED, AS TO MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE, OR ANY OTHER MATTER WITH RESPECT TO ANY OF THE GOODS OR SERVICES. It is understood
that corrosion or erosion of materials is not covered by our guarantee.
2. LIMITATION OF REMEDY AND LIABILITY: SELLER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN
PERFORMANCE. THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF WARRANTY HEREUNDER SHALL BE LIMITED TO
REPAIR, CORRECTION, REPLACEMENT, OR REFUND OF PURCHASE PRICE UNDER THE LIMITED WARRANTY CLAUSE IN
SECTION 1 HEREIN. IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN
CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT, OR OTHERWISE), SHALL SELLER'S LIABILITY TO
BUYER AND/OR ITS CUSTOMERS EXCEED THE PRICE TO BUYER OF THE SPECIFIC GOODS MANUFACTURED OR SERVICES
PROVIDED BY SELLER GIVING RISE TO THE CLAIM OR CAUSE OF ACTION. BUYER AGREES THAT IN NO EVENT SHALL
SELLER'S LIABILITY TO BUYER AND/OR ITS CUSTOMERS EXTEND TO INCLUDE INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE
DAMAGES. THE TERM “CONSEQUENTIAL DAMAGES” SHALL INCLUDE, BUT NOT BE LIMITED TO, LOSS OF ANTICIPATED
PROFITS, LOSS OF USE, LOSS OF REVENUE, AND COST OF CAPITAL.
Precautions and warnings
Note
The analyzer electronics and oven assembly, when housed inside a purged enclosure, meet the certifications and classifications
identified in the Specifications section of the this manual (see ) and in the Rosemount 700XA Product Data Sheet, which is located
on the Rosemount website (Emerson.com/Rosemount). Emerson does not, however, accept any responsibility for installations of
these, or any attached equipment, in which the installation or operation thereof has been performed in a manner that is negligent
and/or non-compliant with applicable safety requirements.
2
WARNING
SAFETY COMPLIANCE
Install and operate all equipment as designed and comply with all safety requirements. The seller does not accept any
responsibility for installations of the Rosemount Gas Chromatograph or any attached equipment in which the installation or
operation thereof has been performed in a manner that is negligent and/or non-compliant with applicable safety requirements.
WARNING
SAFETY COMPLIANCE
If the unit is not operated in a manner recommended by the manufacturer, the overall safety could be impaired.
WARNING
SUPPLY MAINS CONNECTION
The unit is intended to be connected to supply mains by qualified personnel in accordance with local and national codes.
WARNING
EXPLOSION HAZARD
Do not open when energized or when an explosive atmosphere is present.
WARNING
EXPLOSION HAZARD
Keep cover tight while circuits are live.
WARNING
EXPLOSION HAZARD
Use cables or wires suitable for the marked "T" ratings.
WARNING
EXPLOSION HAZARD
Cover joints must be cleaned before replacing the cover.
WARNING
EXPLOSION HAZARD
Conduit runs to GC enclosure must have sealing fitting adjacent to enclosure.
WARNING
VENTILATION
The unit is required to be used in a well ventilated area.
3
WARNING
LEAK TESTING
All gas connections must be properly leak tested at installation.
WARNING
PRECAUTIONARY SIGNS
Observe and comply with all precautionary signs posted on the GC. Failure to do so may result in injury or death to personnel or
cause damage to the equipment.
WARNING
VENTILATION
If you plan to place the GC in a sealed shelter, always vent the GC to atmosphere with ¼-in. tubing or larger. This will prevent the
build up of H2 and sample gas
WARNING
TOXIC VAPORS
Exit ports may discharge dangerous levels of toxic vapors.
Use proper protection and a suitable exhaust device.
WARNING
BURN HAZARD
Some parts of the analyzer may be heated to 120 °C (248 °F).
To prevent burns, do not touch any of the hot parts. All parts of an analyzer are always hot unless it has been switched off and
allowed to cool down.
Before fitting, removing, or performing any maintenance on the analyzer, make sure that it ha been switched off and allowed
to cool for at least two hours.
When handling the analyzer, always use suitable protective gloves.
These precautions are particularly important when working at heights.
If burned, seek medical treatment immediately.
Failure to observe this warning could cause an explosion or potentially hazardous situation, which if not avoided, may cause
personal injury or death.
CAUTION
REPLACEABLE PARTS
No user replaceable parts inside except a few parts which are only to be accessed by trained service personnel. All replacement
parts must be authorized by Rosemount to ensure product certification compliance.
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end users’ equipment. This could
be intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting your system. Restrict physical access
by unauthorized personnel to protect end users’ assets. This is true for all systems used within the facility.
4
NOTICE
The Rosemount 700XA is CSA-certified and ATEX-certified. See the certification tag on the GC for specific details about its agency
approvals.
NOTICE
When the vapor regulators and flow switches are fitted, they must be suitably certified with the ratings Ex d IIC Gb T6/T4/T3 and
for a minimum ambient temperature range Ta = -4 °F to +140 °F (-20 °C to +60 °C).
NOTICE
Where right angle bend cable adapters are used, they shall be appropriately certified and shall interface with enclosures via
appropriate certified barrier glands.
5
6
Contents
Chapter 1 Getting started...........................................................................................................9
1.1 Select site.................................................................................................................................... 9
1.2 Unpack the gas chromatograph (GC)...........................................................................................9
1.3 Required tools and components................................................................................................ 11
1.4 Supporting tools and components.............................................................................................12
Chapter 2 Installation and start-up .......................................................................................... 13
2.1 Installation considerations.........................................................................................................13
2.2 Mounting arrangements............................................................................................................13
2.3 Gas chromatograph wiring........................................................................................................ 18
2.4 Electrical installation..................................................................................................................22
2.5 Leak checking and purging for first calibration...........................................................................46
2.6 Start up the system....................................................................................................................50
Appendix A Engineering drawings.............................................................................................. 53
A.1 List of engineering drawings - Rosemount 700XA......................................................................53
Quick Start Guide Contents
00825-0100-3770 July 2020
Rosemount 700XA 7
Contents Quick Start Guide
July 2020 00825-0100-3770
8 Emerson.com/Rosemount
1 Getting started
Emerson started and inspected your gas chromatograph (GC) before it left the factory.
Emerson also installed program parameters and documented them in the GC Config
Report furnished with your GC.
1.1 Select site
The site you select for the gas chromatograph (GC) is important for measurement
accuracy.
Procedure
Install the GC as close as possible to the sample system, but allow for adequate access
space for maintenance tasks and adjustments.
WARNING
HAZARDOUS AREA EXPLOSION HAZARD
Failure to follow this warning may result in injury or death to personnel.
Do not use a personal computer (PC) or printer in a hazardous area.
Emerson provides serial and Ethernet communication links to connect the analyzer to
the PC and to connect to other computers and printers in a safe area.
Allow a minimum of 3 ft. (0.9 m) in front of the GC for operator access. Ensure that
exposure to radio frequency interference (RFI) is minimal.
1.2 Unpack the gas chromatograph (GC)
Unpack and inspect the Rosemount 700XA gas chromatograph upon receipt.
WARNING
LIFTING HAZARD
The Rosemount 700XA is heavy equipment. Failure to observe this warning may cause
serious injury to personnel.
Use two people to move the GC.
Observe all proper lifting methods as defined by your site operating procedures.
Procedure
1. Unpack the equipment.
a) Remove the Rosemount 700XA from the shipping crate.
b) Remove the USB memory stick containing the software, applications, Quick
Start Guide, and manuals.
Quick Start Guide Getting started
00825-0100-3770 July 2020
Rosemount 700XA 9
Note
The MON2020 version number is located on the back of the USB card.
2. Retain the shipping information.
3. Inspect all parts and assemblies for possible shipping damage.
4. If any parts or assemblies appear to have been damaged in shipment, first file a
claim with the carrier.
5. Next, complete a full report describing the nature and extent of the damage and
forward this report immediately to your Emerson Customer Care representative.
6. Include the GC's model number in the report.
Emerson will provide disposition instructions as soon as possible.
If you have any questions regarding the claim process, contact your Emerson
Customer Care representative for assistance.
Only proceed to install and start up the GC if all required materials are on hand and
free from obvious defects.
Getting started Quick Start Guide
July 2020 00825-0100-3770
10 Emerson.com/Rosemount
Tabla de contenidos
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
