ROSE DISPLAYS ANOKIOSK-STACKABLE Manual de usuario

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de ROSE DISPLAYS

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI SQUARE WITH CABLE CLIP AND CABLE AND... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH CABLE AND SAUCER Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ADVANCETRAK WITH CABLE CLIP AND CABLE Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SQ Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH CABLE CLIP AND LOOP AND... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME ASSEMBLED WITH WALL HANGERS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME WITH CABLE CLIP AND LOOP AND... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH MULTICLIPS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA SQUARE WITH CABLE CLIP AND CABLE AND... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT WEIGHTED BASE Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH MULTICLIPS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ECONOSTAND WITH ANOQUICK Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH CABLE CLIP AND CABLE AND... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOSCREEN WITH VARIO BASE Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH 4 WALL MOUNTS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH ROD, CABLE CLIP AND BALL... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS BUTTERFLY CLIPS WITH BALL CHAIN Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK SQUARE NO HANGING Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND ASSEMBLED-SLATWALL Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND NO LOAD WITH WALL HANGERS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ROPOLE-SPIDER Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH LOOP AND SAUCER AND... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ADVANCETRAK WITH METAL CLIP AND V CLIP Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario