Ronix 4647 Manual de usuario
GASOLINE CHAIN SAW
4647
18"
/450mm
GASOLINE CHAIN SAW
USER MANUAL 1
TECHNICAL SPECIFICATION
Model 4647
Power 1.9kw/8500rpm
Engine Displacement 49.3cm3
Idling speed 3000rpm 200
Fuel Tank capacity 550ml
Sound power Level 117dB
Oil tank capacity 260ml
Net weight 7kgs
Frequency 8500rpm
Bar length 18”
Chain Speed 22m/sec
Brake Time 0.015s
Weight, without bar and chain 5.7kg
PART LIST
18"/450mm
GASOLINE CHAIN SAW
Bar
Low Kickback
Saw Chain
Oil Pump
Fuel Tank Cup
Chain Brake Lever/Front
Hand Guard Starter Handle
Throttle Control
Lockout
Mufe
Front
Handle
Rear Handle/Boot Loop
Filter Cover
Choke Lever
Throttle Control Trigger Chain Screw Adjustment
Nut
GASOLINE CHAIN SAW
2
IMPORTANT SAFETY INSTRUCTIONS
SAFETY ALERT SYMBOLS
Safety alert symbols are used to draw your attention to possible dangers.
These symbols, and their explanations, deserve your careful attention
and understanding. The safety warnings do not by themselves eliminate
any danger. The instructions or warnings they give are not substitutes
for proper accident prevention measures. These safety instructions are
not meant to cover every possible condition that may occur.
BASIC SAFETY PRECAUTIONS
DO NOT rely exclusively upon the safety devices built into the unit.
DO NOT allow the unit to be used as a toy.
Please read the entire operator’s manual carefully before attempting to
assemble, operate or maintain the unit.
Follow all safety instructions. Failure to do so can result in property
damage or serious injury to yourself and/or others.
Be thoroughly familiar with the controls and the proper use of the unit.
Know how to stop the unit and disengage the controls quickly.
Stay alert! Do not operate the unit when tired, ill or under the influence
of alcohol, drugs or medication.
Never allow children to operate the unit. Never allow adults to operate
the unit without proper instruction.
Make sure that all guards and safety attachments are properly installed
before operating the unit.
Keep these instructions. Refer to them often and use them to instruct other
users. If loaning someone this unit, also loan them these instructions.
Keep bystanders, especially children and pets, at least 50 feet (15 m)
away. If anyone enters the work area, stop the unit!
Keep the work area clean. Cluttered areas invite injuries. Do not start
USER MANUAL 3
cutting until the work area is clear and free from obstructions, there is
secure footing and a planned retreat path from falling branches.
Always wear appropriate eye and ear/hearing protection when operating
this unit. Wear safety goggles, or safety glasses with side shields failure
to do so could result in serious eye injury caused by thrown or falling
objects. If the operation is dusty, wear a facemask or dust mask. Use a
hard hat or other type of safety helmet.
Dress appropriately, wear heavy, snug-fitting clothes (long panst and
a long sleeve shirt), non-slip protective gloves and steel-toed safety
boots. Do not wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair above shoulder level to prevent entanglement in
moving parts.
Only use the unit in daylight or good artificial light.
Only use the unit for its intended purpose: to cut wood. Only use the unit
as described in this manual. Only use the manufacturer’s recommended
attachments with this unit.
Rotational Kickback can happen when the upper tip of the guide bar
contacts an object while the chain is moving (Fig. 1&2). This can cause
the chain to dig into the object and momentarily stop moving. The guide
bar is then kicked up and back toward the operator in a lightning-fast
reverse reaction.
- Pinch Kickback can happen when the wood on either side ofa cut
closes in and pinches the moving saw chain along the top of the guide
bar. This can cause the chain to instantly stop. The chain force is then
reversed, causing the saw to move in the opposite direction, sending the
saw straight back toward the operator.
- Pull-ln can happen when the moving chain on the bottom of the guide
bar hits a foreign object inside the wood. This can cause the chain
to suddenly stop. The saw is then pulled forward and away from the
operator, which could potentially result in the loss of control of the saw.
GASOLINE CHAIN SAW
4
18"
/450mm
GASOLINE CHAIN SAW
Fig. 1
Fig. 2
Fig. 3
KICKBACK SAFETY PRECAUTIONS
- DO NOT over reach.
- DO NOT cut above shoulder height.
- DO NOT make cuts with the tip of the guide bar (Fig.1).
- DO NOT let the tip of the guide bar contact any abject, such as a log,
USER MANUAL 5
branch, ground or other obstruction. Remove or avoid any obstructions
that might impact the tip of the guide bar while cutting (Fig.3).
- DO NOT cut more than one log or branch at a time.
- DO NOT twist the saw when removing the guide bar from an undercut
while bucking.
- DO NOT operate the unit with one hand! Serious injury to the operator,
helpers or bystanders may result from one-handed operation. this unit is
intended for two-handed use. Always grip the unit firmly with both hands
when the engine is running. Keep the left hand on the front handle and
the right hand on the rear handle. Use a firm grip with ghumbs and
fingers encircling the handles. A firm grip will help maintain control of the
unit and reduce kickback.
- DO NOT install a bow guide on this unit. Bow guides havea larger
kickback zone, which increases the chance of kickback and serious
injury. This increased risk is not significantly reduced by using a low
kickback saw chain.
Using a bow guide on this unit is extremely dangerous. Never start the
saw when the guide bar is inside an existing cut. Be extremely careful
when re-entering a cut.
Keep proper footing and balance at all times.
- Always begin a cut with the engine running a full speed. Fully squeeze
the throttle control trigger and maintain a steady cutting speed. Slower
speeds increase the chance of kickback. Keep the saw housing pressed
firmly against the wood.
- Watch for shifting logs, branches, or other objects that might pinch, or
fall onto the chain while cutting.
- If using wedges, Only use wedges made of plastic or wood. Do not use
metal to hold a cut open.
- Follow the manufacturer’s sharpening and maintenance instructions
for the saw chain.
- Only use replacement guide bars and chains specified by the
manufacturer or the equivalent.
These are available from authorized service dealers. Use of any
GASOLINE CHAIN SAW
6
unauthorized parts or accessories could lead to serious injury to the
operator or damage to the unit and will void the warranty.
- Use devices, such as low-kickback chains, guide bar nose guards,
chain brakes and special guide bars, which reduce the risks associated
with kickback.
GENERAL SAFETY PRECUATIONS
- DO NOT handle the unit with wet hands.
DO NOT operate a chain saw in a tree or on a ladder unless specifically
trained to do so.
DO NOT use the unit in the presence of flammable liquids or gases.
DO NOT operate a unit that is damaged, improperly adjusted or not
completely and securely assembled. Be sure that the saw chain stops
moving when the throttle control trigger is released. Do not use the unit
if the stop switch does not turn the unit on and off properly or if the
lockout switch does not work. Have defective switches replaced by an
authorized service center.
DO NOT attempt operations beyond the operator’s capacity or
experience.
DO NOT cut near electrical cables or power lines.
- DO NOT force the chain saw, especially near the end of a cut. It will do
a better, safer job when used at the intended rate.
DO NOT touch the engine or muffler. These parts can become extremely
hot during operation and remain hot for a short time after the unit is
turned off.
- To reduce the risk of fire, keep the engine and muffler free from debris,
excessive grease and carbon build up.
- Before cutting, always inspect wood for foreign objects that could
cause injury to the operator or damage to the unit. Never cut through
nails, metal rods, railroad ties or pallets. If a foreign object is struck, stop
the unit and inspect it for damage.
- Keep all body parts away from the saw chain when the engine is
USER MANUAL 7
running. Before starting the saw, make sure the saw chain is not
contacting anything.
- Always stop the engine when operation is delayed, before setting down
the unit or when walking from one location to another. Make sure the
chain comes to a complete stop. Do not leave the unit unattended while
the engine is running. Always stop the engine when not in use.
- To avoid accidental starting, never carry the unit with fingers on the
throttle control trigger. Only pull the starter rope when in the starting
position. The operator and unit must be in a stable position while starting
the engine. Refer to Starting and stopping instructinos.
- Always carry the chain saw by the front handle with the engine off,
finger off the throttle control trigger, the muffler positioned away from the
body and the guide bar and saw chain sheathed in the scabbard and
positioned to the rear.
- Always make sure the stop switch is in the proper position before
starting or stopping the engine.
- When cutting a limb that is under tension, be alert for spring back,
which may cause the operator to be struck when the tension of the wood
fibers is cause the operator to be struck when the tension of the wood
fibers is released.
- Use extreme caution when cutting small-sized brush and saplings, as
slender material may catch the saw chain and be whipped toward the
operator or pull the operator off balance.
MAINTENANCE AND STORAGE SAFETY
If the unit is not working as it should, has been dropped, damaged,
left outdoors or dropped into water, do not use the unit. Have the unit
serviced by an authorized service center.
All service, other than the maintenance procedures described in this
manual, should be performed by an authorized service center.
Follow all maintenance instructions in this manual.
Before inspecting, servicing, cleaning, storing, transporting or replacing any
GASOLINE CHAIN SAW
8
parts on the unit:
1. Stop the engine. Make sure the stop switch is in the STOP position
and the throttle control trigger is released.
2. Make sure all moving parts have stopped.
3. Allow the unit to cool.
4. Make sure the chain brake is disengaged.
Never remove, modify or make inoperative any safety device furnished
with the unit.
For safer, more effective performance, make sure the guide bar and
chain are properly cleaned, lubricated, tightened and sharpened. Check
the guide bar and chain at frequent intervals for proper adjustment.
Frequently inspect the unit for damage. Before further use, any damaged
part should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, fuel leaks and any other
conditions that may affect its operation. damaged parts should be
properly repaired or replaced by an authorized service center, unless
otherwise indicated in this manual.
Use only original manufacturer replacement parts and accessories,
which are designed specifically to enhance the performance and
maximize the safe operation of the product… failure to do so may cause
poor performance and possible injury. Use only the chain and guide bar
supplied with this product be sure to secure the unit while transporting.
Always use the scabbard on the guide bar and saw chain during
transportation and storage.
When not in use, store the unit in a locked-up and dry, or high and dry,
place to prevent unauthorized use or damage. Keep out of the reach of children.
Keep the handles dry, clean and free from debris, oil, fuel and grease.
Clean the unit after each use. Never douse or spray the unit with water
or any other liquid. Do not use solvents or strong detergents.
USER MANUAL 9
KNOW YOUR PRODUCT
This unit may be used for the purposes listed below:
Basic limbing, felling and woodcutting
Removing buttress roots
ACCESSORIES
1. GASOLINE CHAIN SAW-4635
2. BAR
3. CHAIN
4. GUIDE BAR
5. RASPER
6. SCREW DRIVER
7. MEASURING OIL BOTTLE
ORERATION INSTRUCTION
.ADDING BAR AND CHAIN LUBRICANT
The guide bar and saw chain require lubrication to minimize friction.
Never starve the guide bar and chain of lubricating oil. Running the unit
without enough oil will cecrease cutting efficiency, shorten the life of the
saw chain, cause rapid dulling of the saw chain and excessive wear to
the guide bar from overheating. An insufficient amount of lubricating oil
is evidenced by smoke, guide bar discoloration or pitch build-up.
Fill the bar lube reservoir each time the fuel tank is filled. Only use
bar and chain oil that is formulated to perform over a wide range of
temperatures with no diluting required in the bar lube reservoir. Do not
use motor oil or any other petroleum-based oil.
1. Remove the bar lube reservoir cap (Fig. 4)
2. Carefully pour the bar and chain oil into the bar lube reservoir.
3. Replace the bar lube reservoir cap and tighten securely.
4. Wipe off excess oil.
Tabla de contenidos
Otros manuales de Motosierra de Ronix
