Rolls ROTORHORN RP147 Manual de usuario

RP147

ROTORHORN

Rotating Speaker Simulator

RFX

Salt Lake City, UT

LIMITED WARRANTY

This product is warranted to the original consumer purchaser to be

free from defects in materials and workmanship under normal installation,

use and service for a period of one (1) year from the date of purchase as

shown on the purchaser’s receipt.

The obligation of Rolls Corporation under this warranty shall be

limited to repair or replacement (at our option), during the warranty period

of any part which proves defective in material or workmanship under

normal installation, use and service, provided the product is returned to

Rolls Corporation, TRANSPORTATION CHARGES PREPAID. Products

returned to us or to an authorized Service Center must be accompanied by

a copy of the purchase receipt. In the absence of such purchase receipt, the

warranty period shall be one (1) year from the date of manufacture.

This warranty shall be invalid if the product is damaged as a result

of defacement, misuse, abuse, neglect, accident, destruction or alteration

of the serial number, improper electrical voltages or currents, repair,

alteration or maintenance by any person or party other than our own

service facility or an authorized Service Center, or any use violative of

instructions furnished by us.

This one-year warranty is in lieu of all expressed warranties,

obligations or liabilities. ANY IMPLIED WARRANTIES, OBLIGA-

TIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION

TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED

WARRANTY. Some states do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply to you.

IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF

THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,

WHATSOEVER. Some states do not allow the exclusion or limitation of

special, incidental or consequential damages so the above limitation or

exclusion may not apply to you. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state.

OWNERS MANUAL

SPECIFICATIONS

Input Dual 1/4" phone

Output Dual 1/4" phone

Output level +5 dB max

Delay time 6 Ms

Crossover freq 800 Hz

MIDI IN Program change w/omni, ch 1, 9 or 16

Pedal in Momentary contact on tip or ring to ground

Phantom pwr out 12VDC on pins 1 and 3 of the MIDI DIN jack

Size 19 X 1.75 X 6 inches

Power 120 VAC 50/60 Hz 12 VA

INTRODUCTION

Thank you for your purchase of the Rolls RP147 Rotorhorn.The RP147 is a line

level rack mount signal processor for duplicating the sound of a rotating horn

speaker cabinet electronically. It has two-way crossover network as well as

simulated bass and treble “rotors”.It may be controlled by the front panel, remote

foot switch or MIDI program changes and is housed in a single space 19" painted

steel chassis.the RP147 is intended for live performance or studio work, it is

simple to use and is ready to work upon power up.

Features

> Accurate simulation of“Leslie” fast, slow, and brake

> Front panel and footswitch control of all functions

> MIDI control of all functions

> Single space 19" rack chassis

> Both chorus and vibrato modes

> Will phantom power all ROLLS MIDI foot controllers

> Speed may be controlled by controller #4

Using the ROLLS RP147

Connect the signal source to the input jacks on the rear. If a mono source is used use only

“RIGHT IN”and “RIGHT OUT”.The effect will come out both jacks but in“BYPASS”only the

inputs connected will pass through.The “INPUT LEVEL” may be used to match the bypass

signal or make the process signal greater or less. If too much signal is input the special

overdrive circuits offer a “tube” like distortion. The unit may be controlled three ways, front

panel buttons, remote foot switch, and MIDI controller.

If MIDI control is being used connect the controller to the MIDI IN jack on the rear

panel. If a ROLLS MIDI controller is used a power adapter will not be necessary as the

power will be through the cable (as long as the cable has all 5 wires connected). The

RP147 recognizes program change numbers 1 through 5 as follows.

Program change # (numbers starting at 1)

1 > Bypass

2 > Active (nothing changed)

3 > Active slow

4 > Active fast

5 > Active stop

The speed may be controlled by controller #4 on the same channel as the pro-

gram changes.The speed will vary with data #127 being equivalent to the fast speed and

data #0 as stop. If your controller doesn’t have that much range you can still achieve full

speed range by adjusting P2 on the circuit board to full CCW, this will give the maximum

range the controller can give but when it is being used with the other controls the fast speed

will be too fast.Also touching any button or sending a program change will take it out of the

“controller” mode and the RP147 will assume the new parameter, a new controller data #

will have to be sent to resume operation. Adjusting P2 is cause for deep meditation and

soul searching.

On the rear panel is a 3 pin header connector that is used for selecting the MIDI

channel, only channel 1, 9 or 16 may be selected.The unit must be off when changing the

channel, looking at the rear the pins are numbered 3 2 1.With no shorting clip the RP147 is

in “omni” mode, or all channels are recognized.

No pins shorted = all channels recognized

Pins 1 and 2 shorted = channel 9

Pins 3 and 2 shorted = channel 1

Pins 1, 2 and 3 shorted = channel 16

The ROLLS RP8 dual foot switch may be used to control the RP147 by connecting a stereo

cord between the two. This will allow fast/slow and active/bypass control.And it is theoreti-

cally possible to enter “BRAKE” if both are pressed exactly together.

The speeds are controlled internally by trim pots located on the motherboard. P2 controls

the fast speed and P3 the slow.

ROLLS CORPORATION

5968 S 350 W

MURRAY UT 84107

RP147.SCH ?

1992

Titl

Siz : Docum nt Numb r:

Dat :

R v:

Sh t of

RP147 ROTORHORN

+5V

MIDI IN

+5V

AD1

AD2

AD3

AD4

AD5

AD6

AD7

A10

A11

A12

A10

A11

A12

AD0 AD0

AD1

AD2

AD3

AD4

AD5

AD6

AD7

F / S

BRAKE

BPASS

+5V +5V

R IN

L IN

L OUT

R OUT

POWER

+12V

-12V

AC IN

PEDAL

BPASS

BYPASS

+12V

VCC

+12V

-12V

+12V

-12V

+12V

-12V +12V

-12V

+12V

+5V

-12V

+12V

+5V +5V

+12V

-12V

VFAST

VSLOW

VSLOW VFAST

-12V

+12V

-12V

+12V

10K

R11

R30

100K

R31

10K

R34

10K

R46

100K

R49

100K

R68

R69

R70

47K

R73

R74

10K

R75

10K

R77

R78

R80

10K

R81

10K

C22

1UF

C26

25PF

U14

7805

Q0 2

Q1 5

Q2 6

Q3 9

Q4 12

Q5 15

Q6 16

Q7 19

VCC 20

GND

U16

74HC373

A10

A11

A12

PGM

VPP

O0 11

O1 12

O2 13

O3 15

O4 16

O5 17

O6 18

O7 19

VCC 28

GND

U17

27C64

1N4001

LDSG

1N4148

R86

150

PC 1/4

10U

VGG

GND

VDD

O1 7

O2 8

CLK1 2

CLK2 6

U18

MN3007

47U

1K TP

PC 1/4

C24

1N4148

C19

.047

D25

LDRR

D14

1N4148 D15

1N4148

J113

C27

10U

P100K

R72

PC 1/4

1N4001

C23

1UF

C25

25PF

SW2 SW3 SW4

D N 5

R84

D22

1N4148

J113

4.7K

D11

1N751A

R25

100K R26

220K

R27

470K

R28

100K

R29

10K

D18

1N4148

D20

1N4148

1K TP

R35

4.7K

R36

47K

R51

10K

33K

.01

C5 .039

820PF

R56

22K

R57

22K

R58

22K

C16

.001

C18

120PF

C17

.0039

C31

10U

R79

4.7K

R63

10K

R13

10K

R43

22K

R24

22K

CA3080

C34

120PF

H1A

H1B

H1C

C13

C11

25PF

U7A

1458

U4B

1458

U4A

1458

U2A

4558

U8B

4558

U6A

1458

U11A

4558

U2B

4558

U1A

4558

U1B

4558

EA/VP

RESET

INT0

INT1

P1.0

P1.1

P1.2

P1.3

P1.4

P1.5

P1.6

P1.7

P0.0 39

P0.1 38

P0.2 37

P0.3 36

P0.4 35

P0.5 34

P0.6 33

P0.7 32

P2.0 21

P2.1 22

P2.2 23

P2.3 24

P2.4 25

P2.5 26

P2.6 27

P2.7 28

RD 17

WR 16

PSEN 29

ALE/P 30

TXD 11

RXD 10

VCC 40

VSS

U15

80C31

U7B

1458

10K

R71

47K

100K

U19A

4558

U19B

4558

U11B

4558

Q3 2N3906

CLK 11

10 S8

VDD

VSS

U5B

4013

CLK 3

4S6

VDD

VSS

U5A

4013

U10B

4558

R67

10K

R48

100K

R64

10K

R22

10K

C33 120PF

D21 LDRR

C15

47UF

R1 100K

100K

Q10

2N5088

R61

10K

.01

1UF

1U R18

22K

R53

10K

C10 .01

R83

R82 1K

R21

100K

C35

C37

120PF

R55

100K

R60 4.7K R23 47K

C38

120PF C42

1U R21

100K

D17

1N4148

C36

R53

100

2N4124 C31

10U

C41

R19

22K

R45

220K

C14

.047

R47

100K

R41

D23

1N4148

R44 47K

R42 47K

R62

470K

R17

100K

C32

1UF

2N4124

R37

R38 10K

U6B

1458

R39 10K

R40

3.3K

C28

.0047

C30

.01

R12

47K

R87

10K

50K

2N3906

2N4124

R10

47K

R65

10K

R66

10K

C29

.01

R15

18K

.047

R14

47K

THD 8

DG 3

RIN 2

RC 1

GND 4

INV

OUT

V+

0U9A

NE570

THD 9

DG 14

RIN 15

RC 16

GND 0

INV

OUT

V+

13 U9B

NE570

R16

4.7K

C44

.047

C45

.27

C40

.047

R85

470

Q11

2N3904

R50

470

R33

470

12MHz

C76

SW5 SW SPST

PL1

PLUG AC MALE

MC 407 5024

U12

7812

U13

7912

3 4

SO1

4N35

S v ral v rsions of this unit w r mad

S v ral diff r nt opto isolators w r us d

and this sch matic may not apply 100% to all units

(ROLLS RP8)

SCHEMATIC

Otros manuales de Procesador de señales de Rolls

Rolls

Rolls RFX147 Manual de usuario

Manuales populares de Procesador de señales de otras marcas

2Y-LINK Technology

2Y-LINK Technology CI-12-ASP-DAASS Manual de usuario

Crane Song

Crane Song Falcon Manual de usuario

Steg

Steg DSP 6 Manual de usuario

Rocktron

Rocktron INTELLIFEX LTD Manual de usuario

RF-Lambda

RF-Lambda RF1457 Manual de usuario

TC Electronic

TC Electronic DB8 MKII Manual

Acqiris

Acqiris U5309A Manual de usuario

PCI

PCI MicroTrans EQ Manual

Crestron

Crestron Avia DSP-1282 Manual de usuario

turck

turck MS96-11EX0-R/24VDC Manual de usuario

ESX

ESX QUANTUM QL810SP Manual de usuario

Oberheim

Oberheim GM-1000 Manual de usuario

AMC

AMC DSP8X8 Manual de usuario

Planet Audio

Planet Audio PC3.5B Manual de usuario

Behringer

Behringer Super-X Pro CX3400 Manual de usuario

Euphonix

Euphonix DF64 Digital Frame Manual de usuario

Lem Elettronica

Lem Elettronica DSP30-4G Manual de usuario

Radial Engineering

Radial Engineering JX44 V2 Manual de usuario