Rollease acmeda Zipscreen Extreme Manual de usuario

ZIPSCREEN EXTREME

INSTALLATION MANUAL

CONTENTS

DISCLAIMER

INTRODUCTION

This Installation manual for Zipscreen Extreme has been produced by Rollease Acmeda to supply the necessary information for the safe and correct installation of

Zipscreen Extreme.

DISCLAIMER

Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the

completeness or accuracy of the information. Information is supplied upon the condition that the persons receiving the information will make their own

determination as to its suitability for their purposes prior to use. Rollease Acmeda assumes no liability whatsoever for any damages incurred by you resulting from

errors in or omissions from the information included herein. Rollease Acmeda reserves the right to make changes without further notice to any products to improve

reliability, function or design.

All rights are reserved. No part of this document may be reproduced or utilised in any means, by any means, electronic or mechanical including photocopying,

recordings, or by any information storage or retrieval system, without the express permission from Rollease Acmeda.

SECTION 1  INSTALLATION PREPARATION

TOOLS & ADDITIONAL ITEMS REQUIRED ...........................................................................................................3

PREASSEMBLED SHADE COMPONENTS ...........................................................................................................3

PREPARING INSTALLATION SPACE ...........................................................................................................4

SECTION 2  INSTALLATION

BRACKET INSTALLATION | BOX 190 ...........................................................................................................7

BRACKET INSTALLATION | OPEN ........................................................................................................................8

SHADE INSTALLATION FOR BOTH BOX 190 & OPEN BRACKET ...................................................................9

SIDE GUIDE INSTALLATION FOR BOTH BOX 190 & OPEN BRACKET ...................................................10

BOX 190 ONLY  FRONT COVER ......................................................................................................................14

SECTION 3  TROUBLESHOOTING

Page. 3

ZIPSCREEN EXTREME Installation Manual | SEP 2020

PRE-ASSEMBLED SHADE COMPONENTS

TOOLS & ADDITIONAL ITEMS REQUIRED

BOX 190 OPEN BRACKETS

SECTION 1  INSTALLATION PREPARATION

TOOLS REQUIRED

• Drill

• Drill Bits – 3.2mm

• Screw Driver – Philips Head / Flat Head

• Measuring Tape

• Pencil

• Allen Key Set

• Spirit level

ADDITIONAL ITEMS REQUIRED  NOT SUPPLIED

To assemble a ZIPSCREEN EXTREME, the following non-stocked items may be required:

• Screw (For Bracket): M10 – Type and length indicative of mounting surface

• Screw: Self Tapping – Type AB Phillips, Pan Head #6 x ⁄”, Stainless Steel

• Screw: Self Tapping – Type AB Phillips, Pan Head #6 x ⁄”, Stainless Steel

• Rivet: Dome Head, Body Diameter 4mm, Grip Range 4.8 - 6.4, Stainless Steel

• Drill Diameter for 4mm rivets

CHECK SHADE ITEMS:

• Shade Tube Assembly

• Box 190 Bracket Assembly

• Box 190 Front Cover

• Inner Rail Assembly x2

• U Mounting Rail x2

• Fixing Rail (Face Fix ONLY) x2

• Rivets & Screws (as required)

CHECK SHADE ITEMS:

• Shade Tube Assembly

• Bracket Assemblies

• Inner Rail Assembly x2

• U Mounting Rail x2

• Fixing Rail (Face Fix ONLY) x2

• Rivets & Screws (as required)

D1 D2

Page. 4 ZIPSCREEN EXTREME Installation Manual | SEP 2020

PREPARING INSTALLATION SPACE

STEP 2  CHECK TOP OF INSTALLATION IS LEVEL

STEP 3  PACK & LEVEL TOP OF INSTALLATION TO SMALLEST DROP DIMENSION

STEP 4  CHECK HORIZONTAL INSTALLATION DIMENSION AT TOP, CENTRE & BOTTOM

SECTION 1  INSTALLATION PREPARATION

If un-even, go to STEP 3

If level, go to STEP 4

D = Drop of Shade

NOTE: In some instances, when the drop is level, D1 & D2 will not be equal as there is uneven ground.

Ensure the smallest value of D1 & D2 = Shade Drop ID specified in initial measurement

W = Width of blind

If W1, W2 & W3 are equal or within 7mm of each other, proceed to STEP 6 for Side Fix

applications or STEP 7 for Face Fix applications.

If W1, W2 & W3 are not equal or within 7mm of each other, review the scenarios

outlined in STEP 5 and determine if and where packing is required.

STEP 1  CHECK FOR OBSTRUCTIONS

Check for any obstructions that may interfere in installation.

e.g. If there is an architrave at the bottom of a post that the Zipscreen Extreme is to be installed into, ensure you prepare the

space for the installation.

This may mean that the installer needs to cut into the architrave to make room for the side rails.

NOTE: AVOID INSTALLING ZIPSCREEN EXTREME IN WINDY CONDITIONS

Page. 5

ZIPSCREEN EXTREME Installation Manual | SEP 2020

PREPARING INSTALLATION SPACE

SECTION 1  INSTALLATION PREPARATION

STEP 5  PACK INSTALLATION WIDTH TO SHADE WIDTH MEASUREMENT

SCENARIO:

PACKING DETAILS:

W3 is greater than W1 & W2

If X1 or X2 is less than 7, no packing is necessary (however, a square space will

provide greater flexibility with the rest of the installation).

If x is equal to or greater than 7, packing is required. Pack out the largest dimensions

(W3) to be within 7mm of the smallest dimension (W1).

Ensure W1 = Blind Width

(Blind width is specified in initial check and measure).

Proceed to STEP 6 for Side Fix applications or STEP 7 for Face Fix applications.

W1 is greater than W2 & W3

Pack space so that the top is equal to or within 7mm of the smallest dimension (W3).

Ensure W3 = Blind Width

(Blind width is specified in initial check and measure).

Proceed to STEP 6 for Side Fix applications or STEP 7 for Face Fix applications.

W2 is greater than W1 & W3

Pack space so that the largest dimension (W2) to be equal to or within 7mm of

smallest dimension (W1 or W3).

Ensure smallest dimension = Blind Width

(Blind width is specified in initial check and measure).

If W1 and W3 sizes are different, minor packing may also be required at these

locations.

Proceed to STEP 6 for Side Fix applications or STEP 7 for Face Fix applications.

D1 D2

Page. 6 ZIPSCREEN EXTREME Installation Manual | SEP 2020

PREPARING INSTALLATION SPACE

SECTION 1  INSTALLATION PREPARATION

STEP 6  CHECK SIDES OF INSTALLATION ARE LEVEL (FOR SIDE FIX APPLICATIONS ONLY)

STEP 7  CHECK & ENSURE THE INSTALLATION IS LEVEL & SQUARE

If X1 or X2 is less than 7mm, no packing necessary (however, a square space will

provide greater flexibility with the rest of the installation).

If X1 or X2 is equal to or greater than 7mm, packing is required.

Pack out the sides so they are level or within 7mm of W1.

Ensure the finished W1 width = Blind Width.

(Blind Width is specified in initial check and measure).

CEILING

157mm (6.18")

123mm (4.84")

BACK

27mm (1.06")

156mm (6.14")

12mm (0.47")

34mm (1.34")

95.50mm (3.76")

62mm (2.44")

102mm (4.02")

47mm (1.85")

13mm (0.51")

47mm (1.85")

102mm (4.02")

62mm (2.44")

13mm (0.51")

CEILING

WALL

FRONT

CEILING

157mm (6.18")

123mm (4.84")

BACK

27mm (1.06")

156mm (6.14")

12mm (0.47")

34mm (1.34")

95.50mm (3.76")

62mm (2.44")

102mm (4.02")

47mm (1.85")

13mm (0.51")

47mm (1.85")

102mm (4.02")

62mm (2.44")

13mm (0.51")

CEILING

WALL

FRONT

CEILING

157mm (6.18")

123mm (4.84")

BACK

27mm (1.06")

156mm (6.14")

12mm (0.47")

34mm (1.34")

95.50mm (3.76")

62mm (2.44")

102mm (4.02")

47mm (1.85")

13mm (0.51")

47mm (1.85")

102mm (4.02")

62mm (2.44")

13mm (0.51")

CEILING

WALL

FRONT

BOX 190

[Refer to deductions for bracket positioning]

Ensure brackets are installed aligned and level.

Holes for M10 Std size fastener - images indicative only.

SIDE FIX

TOP FIX

FACE FIX

Page. 7

ZIPSCREEN EXTREME Installation Manual | SEP 2020

BRACKET INSTALLATION | BOX 190

SECTION 2  INSTALLATION

Page. 8 ZIPSCREEN EXTREME Installation Manual | SEP 2020

OPEN BRACKETS:

BRACKET INSTALLATION | OPEN

SECTION 2  INSTALLATION

Face Fix Side Fix Top Fix

GENERAL MOUNTING NOTES:

• Install brackets to wall/ceiling using appropriate fixings to suit application.

• Use existing holes in brackets as a guide.

• Ensure brackets are aligned & level.

• Measure brackets end to end to confirm measurement is correct.

Page. 9

ZIPSCREEN EXTREME Installation Manual | SEP 2020

SECTION 2  INSTALLATION

STEP 4  RUN SHADE DOWN STEP 5  ADJUST FABRIC SO THAT IT IS

CENTRED WITH SYSTEM

SHADE INSTALLATION FOR BOTH BOX 190 & OPEN BRACKET

STEP 1  REMOVE SCREW FROM ZAMAK ADAPTOR & BOLT FROM IDLER ADAPTOR

STEP 2  MOUNT SHADE TO BRACKETS MOTOR END FIRST

STEP 3  FASTEN SHADE IN PLACE WITH FASTENERS REMOVED IN STEP 1

STEP 6  TEST SHADE OPERATION

Ensure wiring is correct and motor is operating correctly.

Zamak Adaptor Idler Adaptor

Motor End Idler End

Page. 10 ZIPSCREEN EXTREME Installation Manual | SEP 2020

SIDE GUIDE INSTALLATION FOR BOTH BOX 190 & OPEN BRACKET

SECTION 2  INSTALLATION

STEP 1  MOUNT FIXING RAIL TO WALL ON BOTH SIDES (FOR FACE APPLICATIONS ONLY)

TOP VIEW

IMPORTANT:

• FASTENERS MUST BE SUITABLE FOR FIXING TO SUBSTRATE.

NOTES:

• Fixing Rail protudes from the profile of bracket.

• Ensure the top of Fixing Rail is located against the bracket.

SIDE VIEW

Otros manuales para Zipscreen Extreme

Tabla de contenidos

Otros manuales de Persiana de ventana de rollease acmeda

rollease acmeda

rollease acmeda Automate FT Manual de usuario

rollease acmeda

rollease acmeda Automate MT01-1325-069001 Manual de instalación

rollease acmeda

rollease acmeda Easy Spring Wand Manual de usuario

rollease acmeda

rollease acmeda CU40 Manual de usuario

rollease acmeda

rollease acmeda MULTI-LINK Manual de usuario

rollease acmeda

rollease acmeda Easy Spring Air Manual de usuario

rollease acmeda

rollease acmeda SKYLINE BOTTOM UP Manual de usuario

rollease acmeda

rollease acmeda Zipscreen Extreme Manual de usuario

rollease acmeda

rollease acmeda Easy Spring Wand Manual de usuario

rollease acmeda

rollease acmeda KUMO Manual de usuario

rollease acmeda

rollease acmeda Zipscreen Extreme Manual de usuario

rollease acmeda

rollease acmeda AUTOMATE MT01-1320-069001 Manual de instalación

rollease acmeda

rollease acmeda WireGuide Skylight Manual de usuario

rollease acmeda

rollease acmeda Easy Link Manual de usuario

rollease acmeda

rollease acmeda ZIPSCREEN Manual de usuario

rollease acmeda

rollease acmeda Zipscreen-Skylight Manual de usuario

rollease acmeda

rollease acmeda Easy Spring Air Guía de configuración

rollease acmeda

rollease acmeda SS38 Manual de usuario

rollease acmeda

rollease acmeda S100 EXTREME SYSTEM Manual de usuario

rollease acmeda

rollease acmeda RB12 AERO-DUAL Manual de usuario

rollease acmeda

rollease acmeda Easy Spring Air Guía de configuración

Manuales populares de Persiana de ventana de otras marcas

Jysk

Jysk ROGEN Manual de usuario

SOMFY

SOMFY 1241752 Manual de usuario

Rollos

Rollos S-Nanorollo V2 Guía de planificación

Teptron

Teptron Move Manual de usuario

Renson

Renson Outdoor Loggia Guía de seguridad

Project Source

Project Source CDLF2342W Manual de usuario

Domondo

Domondo PureNight Manual de instrucciones de instalación

IKEA

IKEA KADRILJ Manual de usuario

Hallis Hudson

Hallis Hudson Rolls Super glide Manual de usuario

Benthin

Benthin P1614 Manual de usuario

MV LINE

MV LINE CLARA 015 Manual de instrucciones

Current

Current E-WAND Guía

weinor

weinor VertiTex ZipR Manual

Roto

Roto ZAR M R4/R7 Manual de usuario

SOMFY

SOMFY Movelite WT Series Manual de usuario

Acmeda

Acmeda RF400 Series Manual de usuario

Motura

Motura Pli_353/3 Manual de usuario

Cosiflor

Cosiflor VS 2 Manual de usuario