Roland RS-09 Manual de usuario

Tubbutec OrganDonor

Installation manual for Roland RS-09

Tools you will need:

•Soldering iron

•Wire stripper

•Metal drill 3.5mm or similar)

•Metal drill for a 15mm hole stepping drill for example)

•Center punch

•Screw driver

•Stranded wire to extend the power and MIDI connectors

Included in the kit:

•OrganDonor Main Board

•3x organ Donor Switch Board, 2x 16pin connector, 1x 20pin

connector

•Analog switch connection: 2x16 – 38cm + 40cm 1x20 - 32cm

•Interconnect cables: 1x 6cm, 1x 19cm, 1x 20cm

•Midi connector assembly

•Power connector

•Learn button

•Midi socket drill guide

•2x M3 bolt, 2xM3 nut for midi socket

Principle of operation

OrganDonor uses analog switches to simulate keyboard presses directly.

Normally this would require to solder two wires for each key. Luckily this

can often be avoided by grouping common signals. OrganDonor features

solder jumpers to connect common signals on the back of each analog

switch board. We already connect these jumpers for you.

In the case of the Roland RS-09 there is 1 common signal.

Installation

Before you place the boards please stick insulation tape on the bottom

side of the boards to prevent short circuits with the case. Then stick

double-sided tape on top of the insulation tape and place the boards on

the bottom of the case under the keyboard like shown in the picture.

Plug in the interconnection cables and the switch board cables.

Now solder the switch board wires to the key contacts:

Take care that you don’t accidentally desolder the internal wires.

Switch board 1:

Wires 1 – 16 get soldered to key contacts 1 – 16.

Switch board 2:

Wires 1 – 16 get soldered to key contacts 17 – 32.

Switch board 3:

Wire 1 gets cut.

Wire 2 gets soldered to the common connection bus bar).

Wires 3 – 14 get soldered to key contacts 33 – 44.

Wires 15 – 18 are not used.

Wires 19 and 20 get cut.

Power connection

You need to extend the wires of the power connector by about 20cm.

To do so take some stranded wire with different colors, strip and solder

to the power connector wires. Use shrinking tube to cover the joints.

Then guide the wires under the keyboard to the power supply board.

Then solder the wires to the power supply board.

The yellow wire gets soldered to the -14V terminal, the black wire to the

ground GND) terminal and the red wire to the +14V terminal.

Installing the midi socket

The midi socket can be installed on the back of the machine, we

recommend the space right next to the external input. As the space is

very tight you could also use a 3,5mm stereo jack instead of the

standard MIDI socket.

Use the provided drill guide to center punch the locations of the 3 holes.

The two small holes need to be about 3.5mm in diameter, the large hole

15mm. Here we typically use a stepping drill.

Installing the learn button

The optional learn button can be used to set midi channel. It needs to be

connected to the IO “2” and “G” pin on the main board. The back of the

main board has labels on it). Wires are not included in the kit.

Press the learn button and while it is pressed send a midi note on any

midi channel. OrganDonor will use this midi channel from now on. These

settings are saved.

Configuration

We already flashed the corresponding configuration file to Organ Donor.

There is, however, a software configuration tool available, in case you

want to play around with settings and key assignments.

You`ll find the configurator here:

https://tubbutec.de/files/organDonor/

tubbutecOrganDonorConfigurator.html

This is a browser application, it works with Chrome and Safari right

away, Firefox needs to be configured for web MIDI.

The configurator allows you to upload your settings directly from your

browser to OrganDonor, safe and load settings and export settings as

SysEx files for uploading to Organ Donor via another SysEx tool.

Otros manuales para RS-09

Tabla de contenidos

Otros manuales de Sintetizador de Roland

Roland

Roland JX-305 Manual de usuario

Roland

Roland JUNO-60 Manual de usuario

Roland

Roland JX-305 Manual de operación y mantenimiento

Roland

Roland SH-32 Manual de usuario

Roland

Roland VP-770 Manual de instalación y funcionamiento

Roland

Roland JP-4 Manual de operación y mantenimiento

Roland

Roland EM-305 Manual de usuario

Roland

Roland V-Synth Manual de usuario

Roland

Roland JUNO-60 Manual de operación y mantenimiento

Roland

Roland Fantom XR Manual de operación y mantenimiento

Roland

Roland System-8 Manual de usuario

Roland

Roland GW-7 Manual de usuario

Roland

Roland TB-303 Manual de operación y mantenimiento

Roland

Roland GR-55 Manual de usuario

Roland

Roland Edirol StudioCanvas SD-80 Manual de operación y mantenimiento

Roland

Roland GR-500 Manual de usuario

Roland

Roland RS-50 Manual de usuario

Roland

Roland MKS-30 Manual de operación y mantenimiento

Roland

Roland VIMA RK-300 Manual de usuario

Roland

Roland DisCover 5 Manual de usuario

Roland

Roland JX-10 Manual de usuario

Roland

Roland SonicCell Manual de instrucciones

Roland

Roland GR-30 Manual de usuario

Roland

Roland Boutique JX-03 Guía de instalación

Manuales populares de Sintetizador de otras marcas

Kawai

Kawai MP7 Manual técnico

Joranalogue

Joranalogue Contour 1 Manual de usuario

Full Bucket Music

Full Bucket Music Mono/Fury Manual de usuario

Kawai

Kawai PH50 Manual de usuario

IK Multimedia

IK Multimedia UNO Synth PRO X Manual de usuario

Behringer

Behringer DEEPMIND 12 Manual de usuario

Gotharman

Gotharman Gotharman's anAmoNo-box Manual de usuario

Yamaha

Yamaha DX21 Manual de usuario

QuStream

QuStream HDFS-550 Manual de usuario

Modal Electronics

Modal Electronics ARGON8 Manual de usuario

Octave

Octave Cat SRM Manual de usuario

Dreadbox

Dreadbox Murmux Initiate Manual de usuario

neutral labs

neutral labs ELMYRA 2 Manual de usuario

Waldorf

Waldorf KYRA Manual de usuario

Tubbutec

Tubbutec Juno-66 Manual de usuario

EFM

EFM VCADSR - 3510 Manual de usuario

Yamaha

Yamaha MOTIF XF Manual de usuario

Korg

Korg Poly-800 Manual de usuario