Roger IOS-1 Manual de usuario

Roger Access Control System

IOS-1

Input-output simulator

User Manual

Product version v1.0

Document version: Rev. A

IOS-1 input-output simulator Rev.A.doc 2/21/2011

Strona 2z 4

General

IOS-1 module enables simulation of NO/NC input lines as well as visualization of status at output

lines (both relay and transistor types). The module can be used for education, testing or

demonstration in regard of alarm and access control devices. IOS-1 does not require power supply.

Circuit for input simulation and circuit for visualization of output status are independent of each

other.

Operation

General diagram of operation and exemplary application of IOS-1 are shown in figure below.

Z and COM terminals are used for simulation of input line. Input line can be configured by means of

jumpers as NO (Normally Open) or as NC (Normally Close). In case of NO setting, pressing TRIG.

button results in activation of Q1 output transistor and consequently shorting of Z terminal with

GND. In case of NC setting, output transistor is normally activated, Z and COM terminals are shorted

and pressing of TRIG. button results in deactivation of output transistor and consequently

disconnection between Z and GND terminals.

Note: COM terminal must be connected to lower potential than Z terminal. Typically COM terminal at

IOS-1 module is connected to GND or COM terminal of the tested device.

+12V and GND terminals enable visualization of status at output line. Voltage feeding in range of

5..15V between mentioned terminals results in LED lighting up on board. LED activation can be

caused by negative voltage at GND terminal or positive voltage at +12V terminal. Typically, such

solution enables signaling of status for any relay or transistor output line with negative or positive

output voltage.

IOS-1 input-output simulator Rev.A.doc 2/21/2011

Strona 3z 4

Technical Specification

Parameter Characteristics

Environmental class

(according to EN

50131-1)

Class I, indoor conditions, temperature range: +5°C to +40°C, relative

humidity: 0 to 95% (non condensing)

Module dimensions 35 X 43 mm

Module weight ~ 10g

Certificates CE

Product History

Hardware Firmware Date Description

v1.0 - Initial version of the product

IOS-1 input-output simulator Rev.A.doc 2/21/2011

Strona 4z 4

Ordering information

IOS-1 I/O Simulator module (electronic module only)

This symbol placed on a product or packaging indicates that the product should

not be disposed of with other wastes as this may have a negative impact on the

environment and health. The user is obliged to deliver equipment to the

designated collection points of electric and electronic waste. For detailed

information on recycling, contact your local authorities, waste disposal company

or point of purchase. Separate collection and recycling of this type of waste

contributes to the protection of the natural resources and is safe to health and

the environment. Weight of the equipment is specified in the document.

Contact

Roger sp.j.

82-400 Sztum

Gościszewo 59

Tel.: +48 55 272 0132

Fax: +48 55 272 0133

Tech. support: +48 55 267 0126

E-mail: biuro@roger.pl

Web: www.roger.pl

Tabla de contenidos

Otros manuales de Sistema de control de Roger

Roger

Roger H70/104AC Manual del producto

Roger

Roger PSD4D Manual de usuario

Roger

Roger MCT12E Manual de usuario

Roger

Roger MCT82M-IO-HR Manual de usuario

Roger

Roger B70/2DC Manual del producto

Roger

Roger MCT88M-IO Manual de usuario

Roger

Roger H85/TDR Manual del producto

Roger

Roger MCT12M Manual de usuario

Roger

Roger PRT22 Manual de usuario

Roger

Roger PRT12MF-DES Manual de usuario

Roger

Roger MCT80M Manual de usuario

Roger

Roger MCX16-UZ Manual de usuario

Roger

Roger MC16-RAW-KIT Manual de usuario

Roger

Roger PRT32 Guía de instalación

Roger

Roger ASCD-1 Manual de usuario

Roger

Roger MCT80M Manual de usuario

Roger

Roger MC16-PAC-2-KIT Manual de usuario

Roger

Roger MC16-PAC-2-KIT Manual de usuario

Roger

Roger MCT82-FK Manual de usuario

Roger

Roger B73/LTM Manual del producto

Roger

Roger MCT64E-IO Manual de usuario

Roger

Roger OSR88M-IO Manual de usuario

Roger

Roger CPR32-SE v2.0 Manual de usuario

Roger

Roger B71/BCHP HW02 Manual del producto

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario