Robe ROBIN UV Strobe Manual de usuario

Version 1.3

Table of contents

1. Safety instructions ......................................................................................................... 3

2. Fixture exterior view ...................................................................................................... 5

3. Installation....................................................................................................................... 6

3.1 Connection to the mains ............................................................................................ 6

3.2 Installing the gel frame and barndoors....................................................................... 7

3.3 Rigging the xture and oor installation of the xture ................................................ 8

3.4 DMX-512 connection................................................................................................ 13

3.5 Ethernet connection ................................................................................................. 14

4. Control menu map........................................................................................................ 16

5. DMX chart...................................................................................................................... 18

6. Strobe and Special e󰀨ects running ........................................................................... 20

6.1 Strobe ...................................................................................................................... 20

6.2 Special e󰀨ects ......................................................................................................... 20

7. Control menu ............................................................................................................... 22

7.1 Tab " Address" .......................................................................................................... 23

7.2 Tab "Information" ...................................................................................................... 24

7.3 Tab "Personality" ...................................................................................................... 25

7.4 Tab "Manual Control"................................................................................................ 26

7.5 Tab "Stand-alone" .................................................................................................... 26

7.6 Tab "Service" ............................................................................................................ 27

8. RDM ............................................................................................................................... 28

9. Wireless DMX operation .............................................................................................. 28

10. Error and information messages .............................................................................. 29

11. Technical Specications............................................................................................ 30

12. Maintenance and cleaning......................................................................................... 32

12.1 Replacing fuse ....................................................................................................... 32

12.2 Disposing of the product ........................................................................................ 32

13.Extract from a test report of Brno University Of Technology - Light Laboratory..33

14. Appendix ..................................................................................................................... 34

14.1 Strobe and Special e󰀨ects timing .......................................................................... 34

Robin UV Strobe

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE POWERING OR INSTALLING YOUR ROBIN UV Strobe !

Save it for future reference.

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en-

sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes

written in this manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this ma-

nual or any unauthorized modication to the device.

Please consider that damages caused by manual modications to the device are not subject to warranty.

The Robin UV Strobe was designed mainly for indoor use and it is intended for

professional applications only. It is not for household use.

1. Safety instructions

THIS LUMINAIRE IS DESIGNED WITH UV LEDS AND MUST BE INSTALLED IN COMPLIANCE WITH COM-

POTENT TECHNICAL DIRECTIONS TO PREVENT THE USER’S EYE AND BARE SKIN FROM EXPOSURE

TO HARMFUL UV RADIATION.

CE LUMINAIRE EST CONCU POUR ETRE UTILISE AVEC DES LED UV ET DOIT ETRE INSTALLE EN

STRICTE CONFORMITE AVEC LES INSTRUCTIONS AFIN D’EVITER QUE LES YEUX OU LA PEAU L’UTI-

LISATEUR NE SOIENT EXPOSES AUX EFFETS NEFASTES DES RAYONS UV.

CAUTION: Radiation exposure may cause blindness and cancer of skin!

Maximum exposure: 22 minutes at 7m(23ft) distance

29 minutes at 8m(26ft) distance

46 minutes at 10m(32.8ft) distance

103 minutes at 15m(49ft) distance

184 minutes at 20m(65.5ft) distance

Please read an extract from a test report at the end of the user manual.

Risk Group 3 LED product according to ČSN EN 62471.

Make sure that materials which are exposed to the UV radiation will not be damaged!

Make sure that the available voltage is not higher than stated on the rear panel of the xture.

This xture should be operated only from the type of power source indicated on the marking label. If you are

not sure of the type of power supplied, consult your authorized distributor or local power company.

WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable to completely

remove power from unit when not in use or before cleaning or servicing the xture.

The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords

as this can result in re or electric shock.

Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by

persons walking on it.

Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power

cord from time to time.

Refer servicing to qualied service personnel.

Do not look at the xture´s LEDs during operation. The light beam may damage your eyes.

This xture falls under protection class I. Therefore this xture has to be connected to

a mains socket outlet with a protective earthing connection.

Do not connect this xture to a dimmer pack.

To guard against epileptic seizure:

Do not operate the xture near stairways. Provide advance notice that strobe lighting

is in use. Avoid extended periods of continuous ashing, particularly at frequencies of

10 to 20 ashes per second

If the xture has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on

immediately. The arising condensation water might damage your device. Leave the device switched o󰀨 until

it has reached room temperature.

When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, moisture

or dust.

Air vents and slots in the xture are provided for ventilation, to ensure reliable operation of the device and to

protect it from overheating.The openings should never be covered with cloth or other materials, and never

must be blocked.

This xture should not be placed in a built-in installation unless proper ventilation is provided.

Never place lters or other materials over the front glass cover.

Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.

To avoid damage of the internal optical system of the xture, never let the sunlight (or other

light source) lights directly to the lens array, even when the xture is not working !

Keep ammable materials well away from the xture.

Provide a minimum clearance of 0.3 meters around air vents

Always use a secondary safety cable when rigging this xture.

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.

The xture becomes very hot during operation. Allow the xture to cool approximately 20 minutes prior to ma-

nipulate with it.

Operate the xture only after having familiarized with its functions. Do not permit operation by persons not

qualied for operating the xture. Most damages are the result of unprofessional operation!

Please use the original packaging if the xture is to be transported.

Please consider that unauthorized modications on the xture are forbidden due to safety reasons!

If this device will be operated in any way di󰀨erent to the one described in this manual, the product may su󰀨er

damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short-circuit, burns, electric shock, crash etc.

2. Fixture exterior view

4- Antenna

5- DMX IN

6 - DMX OUT

7 - Control buttons

8 - QVGA touch screen

9 - Fuse holder

10 - RJ 45 Input

11 - Power In

12 - Safety screw

13 - Locking mechanism

14 - Safety lock

15 - Screen cover

1- Glass cover and lens array

2 - U-holder

3- Tilt lock

The ENTER/DISPLAY ON button also serves for switching the display on when the xture is disconnected

from mains.

3. Installation

Fixtures must be installed by a qualied electrician in accordance with all

national and local electrical and construction codes and regulations.

3.1 Connection to the mains

For protection from electric shock, the xture must be earthed!

The Robin UV Strobe is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz

AC power source from 100-240 Volts.

Connect the xture to the mains by means of the enclosed power cord

If you need to install other plug on the power cord, note that the cores in the power cord are coloured according

to the following table. The earth has to be connected!

If you have any doubts about proper installation, consult a qualied electrician.

Core (EU) Core (US) Connection Plug Terminal Marking

Brown Black Live L

Light blue White Neutral N

Yellow/Green Green Earth

Do not overload the supply line and the connecting leads.

Wiring and connection work must be carried out by qualied sta󰀨!

3.2 Installing the gel frame and barndoors

Disconnect the xture from mains before the accessory installation.

Never operate the xture with barndoors closed.

1. Put the frame adaptor (1) on the xture and

secure it with four screws (2).

2. Insert the gel frame (4) into slots (3) of

the frame adaptor (1). Use the slots closer to

the glass cover of the xture.

3. Insert the barndoors (5) into second slots (3) of

the frame adaptor (1).

4. Secure inserted barndoors and (or) the gel

frame by means of the two locks (6).

Lift up a little the lock (6) to release it from

the projection (7) and move it to the position

as shown on the picture B until the projection (8)

snaps into lock (6).

Do not operate the xture with unsecured gel

frame or barndoors!

3.3 Rigging the xture and oor installation of the xture

A structure intended for installation of the xture (s) must safely hold weight of the xture(s) placed on it. The

structure has to be certicated to the purpose.

The xture (xtures) must be installed in accordance with national and local electrical and construction codes

and regulation..

For overhead installation, the xture(s) must be always secured with a safety wire

that can bear at least 10 times the weight of the xture(s).

When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,

under high working places and other endangered areas is forbidden.

The operator has to make sure that safety-relating and machine-technical installations are approved by an

expert before taking into operation for the rst time and after changes before taking into operation another time.

The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled

person once a year.

Allow the xture to cool for ten minutes before handling.

The xture should be installed outside areas where persons may walk by or be seated.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working

load limits, installation material being used, and periodic safety inspection of all installation material and the

projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional

companies.

CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety

of a possible installation, do not install the xture!

The xture has to be installed out of the reach of public.

The xture must never be xed swinging freely in the room.

When installing the device, make sure there is no highly inammable

material (decoration articles, etc.) in a distance of min. 0.5 m.

CAUTION!

Use an appropriate clamp to rig the xture on the truss.

Follow the instructions mentioned at the bottom of the xture base.

Make sure that the device is xed properly! Ensure that the

structure (truss) to which you are attaching the xture is secure.

The xture can be placed directly on the stage oor or rigged to the truss. The xture can be rigged to the truss

via Omega holder and one clamp (two holes with 140mm spacing serve for this method of mounting) or using

stacker which allows 2-6 xtures connected in the top-to-bottom method.

For oor installation use a oor stand if two or more xtures are to be stacked

Single xture installation via the omega holder

1. Bolt the clamp (1) to the omega holder (2) with M12 bolt and lock nut through the hole in the holder.

2. Fasten the omega holder to the U-holder (4) of the xture by inserting both quick-lock fasteners (3) into

holes in the U-holder and tighten fully clockwise.

3. Clamp the xture on a truss (12) and tighten the rigging clamp (1).

4. For securing the xture to the truss, install a safety wire that can hold at least 10 times the weight

of the xture. Use only a safety wire with a snap hook with screw lock gate. Pull the safety

wire (11) through the U-holder (4) and around the truss (12) as shown on the picture below.

5. The tilt lock (7) allows to adjust the xture to desired position. In case, that the tilt lock cannot

be loosened (tightened) due to the housing of the xture, pull this tilt lock in a direction from the xture,

turn it to desired position, release it and continue in loosening (tightening) this tilt lock (principle of

a "ratcheting socket wrench").

If two and more xtures are to be connected in a top-to-bottom method, a stacker with two safety wires

has to be used - see article below.

Multiply xtures rigging

Maximum 6 xtures can be connected in the top-to-bottom method

Always use a stacker for a hanging multiply xtures installation . The position of the U-holder allows to tilt the

whole "stack" of xtures.

To change the position of the U-holder

1. In order to release the U-holder (4), press and hold the front part (1) of the pin (2) and pull it out from

the stacker. Use the same way to remove the pin (2) on the opposite side of the U-holder.

2. Move the U-holder to desired position.

3. Press and hold the top part (1) of the pin (2) and push it throw the U-holder into the hole in the stacker.

Secure the second side of the U-holder (4) by inserting the pin (2) into the stacker.

Check, that both sides of the U-holder are securely fastened.

Table of tilt angles for di󰀨erent loads of the stacker

Hole position 1 2 3 4 5 6 7 8 9

2 xtures -22 -10° 0° 10° 20° 30° 37° 45° -

4 xtures -10° -5° 0° 8° 15° 20° 25° 30° 35°

6 xtures -7.5° -3° 0° 5° 10° 15° 20° 22° 26°

To install multiple xtures in a top-to-bottom method

1. Rig the stacker to the truss (4) by means of two omega holders (2) on the U-holder (5) and two clamps (1)

and secure it with two safety wires (15). Use only safety wires with snap hook with screw lock gate.

The snap hooks have to go throw holes in the stacker.

2. Check if the locking mechanism of the rst xture is in an "unlock position" - the lever (18) is in the bottom

position and the red mark (16) is visible.

3. Connect the rst xture with the stacker in a way that feet (8) of the stacker will be

inserted into top openings (14) of the rst xture and move the rst xture in a direction as show

red arrows on the picture below until you feel a stop.

4. Secure the rst xture with the stacker by means of its locking mechanism: move both levers (18)

to the top position until the green mark (17) is visible and move the plastic levers (19) into position under

locking levers (18) until they snap. Now levers (18) cannot be moved to unlock position.

5. Make the secondary securing of the installed xture. Loosen both tilt locks (9) and move the U-holder (13)

to the horizontal position. Loosen the nuts (12) and move the segments (11) towards the stacker nuts (7).

Loosen the nuts (7) and fasten the segments (11) under them. Tighten the nuts (7) and the tilt locks (9).

Always check that locking mechanisms are locked before connecting next xture!

6. Check if the locking mechanism of the second xture is in the "unlock position" - the lever (18) is in

the bottom position and the red mark (16) is visible.

7. Connect the second xture with the rst one in a way that feet (8) of the rst xture will be

inserted into top openings (14) of the second xture and move the second xture in a direction as show

red arrows on the picture above until you feel a stop.

8. Secure the second xture with the rst one by means of its locking mechanism: move both levers (18)

to the top position until the green mark (17) is visible and move the plastic levers (19) into position under

locking levers (18) until they snap. Now levers (18) cannot be moved to unlock position.

9. Make the secondary securing of this xture. Loosen both tilt locks (9) and move the U-holder (13)

to the horizontal position. Loosen the nuts (12) and move the segments (11) towards the nuts (10).

Loosen the nuts (10) and fasten the parts (11) under them. Tighten the nuts (10) and the tilt locks (9).

10. Repeat steps 6-9 for the next xture. In this way, up to six xtures can be connected each other.

11. Check, that all nuts (7), (10) and tilt locks (9) are fully tightened.

Tabla de contenidos

Otros manuales de Equipo de DJ de Robe

Robe

Robe Robin Tarrantula TW Manual de usuario

Robe

Robe CityLine 48 Manual de usuario

Robe

Robe Anolis Calumma S MC Manual de usuario

Robe

Robe pixelPATT Manual de usuario

Robe

Robe ANOLiS Eminere Remote UV 2 Manual de usuario

Robe

Robe Robin MMX Blade Manual de usuario

Robe

Robe Divine 60 UV Manual de usuario

Robe

Robe Robin CycBar 12 Manual de usuario

Robe

Robe iSpiider Manual de usuario

Robe

Robe ROBIN SPIKIE Manual de usuario

Robe

Robe ROBIN MegaPointe Wireless DMX Manual de usuario

Robe

Robe ColorSpot 2500E AT Manual de usuario

Robe

Robe ROBIN ParFect 100 SmartWhite Manual de usuario

Robe

Robe StageQube 324 Manual de usuario

Robe

Robe ANOLIS Side Eminere 2 Wireles DMX Manual de usuario

Robe

Robe Anolis Eminere 2 Wireless DMX Manual de usuario

Robe

Robe Robin CycBar 15 Manual de usuario

Robe

Robe DMX Control 512 Manual de usuario

Robe

Robe Robin LedBeam 150 Manual de usuario

Robe

Robe ROBIN T11 MFS Manual de usuario

Robe

Robe DigitalSpot 3000 DT Manual de usuario

Robe

Robe Robin 1200 Manual de usuario

Robe

Robe redwash 3-192 Manual de usuario

Robe

Robe ColorStrobe IP Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario