Robam Vigour Series Manual de usuario

User Manual

Edition: A/0

Publication Date: July, 16, 2021

If the manual is lost, you can send e-mail to [email protected],

request for an electronic manual.

Gas Hob

JZ(Y/T)-B272

Contents

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

-------------------------------

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

---------------------------------------

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

-----------------------------------

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Notice Items

Important Safety Information

Product Overview

Product Structure

Product Features

Product Parameter

Installation Instruction

Use Instruction

Clean and Maintenance

General Troubleshooting

Attachment

Problem

Ignition

Failure

The burner is

not work

when loosen

the knob

Gas leakage

(gas smell)

Possible Reason

Gas Volve is not open

Air exists in gas pipe

The rubber tube is

twisted or blocked

Electrode needle is dirty

lgnitor malfunction or the electrode

needle in wrong position

Without battery,put battery

oppositely or power insufficiency.

The copper core,copper cover,

burner is in wrong position

Time to press On/Off switch

is too short.

Switch is not closed completely.

The rubber tube is not

connected or cracked.

Burner is blocked

The gas used here is not consonant

with the required in the nameplate.

Gas pressure is unstable,

water in the rubber tube.

Measurement

Turn off the control switch

Then turn on the gas valve

Exhaust the air by igniting repeatedly

Straighten,clean or replaced

the rubber tube

Clean clear

Adjust the electrode needle to burner,

keep the distance3.5-4mm

Install the battery collectly

or replace the battery

Install the copper core,copper

cover,burner in right position

Keep the switch down 3-5

seconds then loosen

Turn off the switch

Connect rubber tube or replace it

Choose the cooktop properly

Get rid of water in the rubber tube

Burning

abnormal

or sounding

noise

Clear away the block

General Troubleshooting

Attachment

1. One copy of the Operation Manual

2. Two pieces of anchor ear (except for metal soft pipe)

3. One copy of Installation templet

4. One piece of battery in the packing foam

Gas Hob

Notice Items

1. Please make sure the source of gas is in line with that noted

on nameplate before your installation of the product, otherwise

it is strictly prohibited to use.

2. The minimum distance between the gas stove and gas

resource should be no less than 1 meter and connecting tube

should be the matched special gas tube, which should be

replaced once a year at a regular limitation. The regular length

of the tube should be 1-1.5 meter as preferred. It is highly

required that the tube should be avoided from pressing, heavy

bending or aging. The joining point should be carefully checked

to avoid any possibility of leaking and any potential damage

from the leaking.

4. The fixing metal joint should be installed strictly according to

the operation manual, which lays in the “package of the fixing

metal joint” or installed by the professional staff, if the tube is

connected by the fixing metal joint. The test of leaking should

be done before use. (The way of leaking test above is for your

reference ).

5. The gas stove should be installed on the place of well-

ventilated, but should be avoided from the strong wind.

6. Do not try to cover the flame on the gas stove, or put

anything tinder around. Besides the gas stove cannot be used

to for drying towel or clothes, etc.

7. Do not have the immediate touch on the flame-around area,

such as work stand, burner or cooktop after the use of the gas

stove.

8. Do not try to beat the cooktop, and the special attention

should be paid to keeping the gas stove in good condition

during the transport and installation.

9. Once any leaking tested, the valve should be turned off

immediately and the window should be open to keep ventilated.

The electric fan or range hood or any other electric appliances

are prohibited to use, and keep the fire away. Meanwhile,

please contact professional staff.

10. If there were any abnormal sound such as whir heard, or the

color of flame turned from dark to light or turned muddy, the

backfire from the burner might be happened. Please turn off the

switch, and check whether the burner and copper core are well-

positioned. Turn on the switch in half a minute after the check.

Gas Hob Gas Hob

3. Leave the valve of the gas inflow tube under normal situation.

The leaking test should be done after any abnormal change of

the valve. (Put the low-concentrated cleaning solution to the

joint point and then turn on the valve to check whether any air

bubble appears, if there were any air bubble, the valve should

be turned off immediately and fix the problem. It cannot be used

until the problem is completely solved).

WARNING: THE GAS STOVE SHOULD BE ONLY

CONNECTED BY THE QUALIFIED SPECIAL TUBE(e.g. the

tube made of UV-PSA, Buna-N rubber ). IT IS HIGHLY

PROHIBITED FROM USING NORMAL RUBBER TUBE, FOR

THE POSSIBLE CHEMICAL REACTION MAY HAPPEN WHEN

THE NORMAL RUBBER TUBE MEET OZONE/LIQUID OIL,

WHICH WILL POSSIBLY CAUSE THE DAMAGE OF THE

TUBE AND THE RELATED POTENTIAL ACCIDENTS.

Important Safety Information

General

Information

THIS PRODUCT BELONGS TO THE EMBEDDED HOUSEHOLD GAS

STOVE, YOUR SAFETY IS OF THE UTMOST IMPORTANCE TO

ROBAM APPLIANCES CO.,LTD.PLEASE MAKE SURE THAT YOU

READ THIS INSTRUCTION BOOKLET BEFORE ATTEMPTING TO

INSTALL OR USE THE APPLIANCE. IF YOU ARE UNSURE OF ANY

OF THE INFORMATION CONTAINED IN THIS BOOKLET, PLEASE

CONTACT THE ROBAM APPLIANCES CO.,LTD.

Gas Hob Gas Hob

11. Each time of turn-on the switch should be no more than 20

seconds to avoid from deflagrating. If the switch cannot be

turned on within five times, please contact the service

immediately.

12. The children are prohibited to use the gas stove in the case

of safety concern.

13. The installation and any maintenance should be taken only

by the professionals.

14. Be sure to keep your head away from the burner while the

operation of turn-on gas stove. Please turn off the valve of gas

and switch of gas stove after the use to avoid from any possible

accident.

15. Be sure to keep any heat conductor such as metal knife,

fork or cover away from the heat.

◆This appliance is designed for domestic household use and for the cooking and

frying of domestic foodstuffs.

◆IMPORTANT: The adjacent furniture and all materials used in the installation must

be able to withstand a minimum temperature of 85°C above the ambient

temperature of the room it is located in, whilst in use.

◆Certain types of vinyl or laminate kitchen furniture are particularly prone to heat

damage or discolouration at temperatures below the guidelines given above.

◆Any damage caused by theappliance being installed in contravention of this

temperature limit, will be the liability of the owner.

◆Your new appliance is guaranteed against electrical or mechanical defects, subject

to certain exclusio that are noted in ROBAM APPLIANCES CO.,LTD.conditions of

guarantee. The foregoing does not affect your statutory rights.

◆The use of this appliance for any other purpose or in any other environment

without the express agreement of ROBAM APPLIANCES CO.,LTD.will invalidate any

warranty or liability claim.

◆You should not use this appliance to store items on or as a work surface.

◆Do Not Modify This appliance.

◆You should not store or place flammable or highly flammable liquids/materials on

top of or near the appliance. Items made from aluminium, plastic or plastic film should

also be kept away from the appliance, as they may fuse to the surface.

◆Repairs may only be carried out by ROBAM APPLIANCES CO.,LTD.service

engineers or their authorized service agent.

General Safety

◆Installation must be carried out by an AUTHORISED PERSON in accordance with

the regulation in force.

◆Care should be taken to ensure that the units and work surfaces that you build the

appliance into, meet with The relevant standards.

◆This appliance is not intended for use by persons(including children)with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

◆DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE APPLIANCE

STORAGE DRAWER OR NEAR THIS APPLIANCE.

◆DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT

IS IN OPERATION.

◆DO NOT MODIFY THIS APPLIANCE.

◆DO NOT USE THIS APPLIANCE AS A SPACE HEATER.

Child Safety

◆ROBAM APPLIANCES CO.,LTD.strongly recommend that babies and young

children are prevented from being near to the appliance and not allowed to touch the

appliance at any time. During and after use, all surfaces will be hot.

◆If it is necessary for younger family members to be in the kitchen, please ensure

that they are kept under. close supervision at all times.

◆Older children should only be allowed to utilise the appliance when supervised.

◆Children should be supervised to ensure that they do not play with the appliance.

During Use

◆Any film or stickers that are present on the hob surface when it is delivered should

be removed before use.

◆These instructions are only valid if the country symbol appears on the appliance.If

the symbol does not appear on the appliance, it is necessary to refer to the technical

instructions, which will provide the necessary instructions concerning modification of

the appliance to the conditions of use of the country.

Gas Hob Gas Hob

Product Overview

Dear Users:

Thank for your buying our gas hob. This gas hob adopt advanced technology, fashion

design and optimistic structure. This gas hob has high heat efficiency and safe

operation, too.

Please read this operation manual carefully before installation or operation of this

product. Meanwhile, please keep it properly for future reference.

◆Prior to installation, ensure that the local distribution conditions (nature of the gas

and gas pressure) and the adjustment of the appliance are compatible.

◆The adjustment conditions fro this appliance are stated on the label (or data plate).

◆This appliance is not connected to a combustion product evacuation device.It shall

be installed and connected in accordance with current installation regulations.

Particular attention shall be given to the relevant requirements regarding ventilation.

◆CAUTION: The use of a gas cooking appliance results in the production of heat

and moisture in the room in which it is installed. Ensure the kitchen is well ventilated,

keep natural ventilation holes open or install a mechanical ventilation

device(mechanical extractor hood).

◆CAUTION: This appliance is for cooking purposes only. It must not be used for

other purposes, for example room heating.

◆Prolonged intensive use of the appliance may call for additional ventilation, for

example opening of a window or more effective ventilation, for example increasing

the level of mechanical ventilation where present.

◆Care should be used when utilising the appliance, otherwise there is a risk of burns

being caused.

◆You should not allow the electrical connection cables to come into contact with the

hob surface when it is hot or any hot cookware.

◆If fat and oil overheats, then it can ignite extremely quickly. For this reason, when

cooking with fat and oil the appliance should not be left unattended.

◆Make sure that all of the cooking zones are switched off after use.

CAUTION: “In case of hotplate glass breakage:

- shut immediately off all burners and any electrical heating element and

isolate the appliance from the power supply

- do not touch the appliance surface

- do not use the appliance.”

Product Features

1. Fashionable design: The design of model and structure comply with fashion and

adapt to modern kitchen.

2. Excellent quality: Top quality of accessories with trustable quality, long life

expectancy.

3. Electronic pulse with flame failure safety device on each burner and high thermal

efficiency.

4. Full air in flow: Built-in structure with full air in flow , cooktop supplyment air, air

valve adjust flexibly, burn completely and easy to install.

5. Anti-explosive enamel glass, use safely and easy to clean.

6. Pan Diameter limits

Wok burner (5.0kW): 220mm ~ 300mm

Remark: It's prehibited to use a vessel that overlap its edges.

Using inappropriate hob guards can cause accidents.

Product Structure

(This picture is only for your reference. There are series of models, we don’t list all

of them one by one .)

Gas Hob Gas Hob

Product Parameter

Note:

1. Parameters indicate for reference only. The exact datas should be confirmed on

the nameplate on the gas hob.

2. The installation size of built-in gas hob should be confirmed by the specification on

the templet in the carton.

3. We keep right to alter design or specification.

Installation Instruction

1. When the Gas Hob is installed, the distance from the combustibles is not less than

15cm, and the distance between the Gas Hob and noncombustible should be not

less than 7 cm; The Gas Hob and the above object should have a height of more

than 100cm, If you want to install a Rang Hood, the height of 65-75cm from the Gas

Hob is suitable. (This space is set up according to the installation requirements of the

Range Hood).

2. The kitchen cabinet for built-in gas stove should be specially designed for the

safety concern. The ventilated borehole should be suitable for the safety requirement

and the size should be no less than 100 cm .

3. When the special gas tube is used, one side of the tube should be connected with

the gas valve while the other side connected with the inflow side of gas stove. Please

take off the cover on the connection point and put the tube to cover the red-mark

point, and tighten it with the anchor ear. Be sure that the leaking test should be taken

before use.

4. The size of the borehole should be taken according to the requirement, and put the

built-in gas stove to match the borehole.

5. If the G1/2”inch connector is used, please make sure to put the rubber gasket

inside the connector and the leaking test should be taken before use.

6. The qualified reduction valve should be used when the LPG is used as the source

of the gas.

Requirement for hole size

Item Name

Model

Gas Category, type

Gas inlet connection

Product Size(mm)

Hob Element Number

Air in flow

Panel

Ignition Method

Flame failure safety

device

Gas Hob

780×450×130

12.4

Full

Tempered Glass

650×350×R10

Electronic Pulse

Yes

28-30 mbar

Net Weight(kg)

Size Of Opennings(mm)

Total: 10.0kW (728g/h)

Left burner: 5.0kW (364g/h)

Right burner: 5.0 kW (364g/h)

I3B/P(30), G30, G31 or their mixtures

Injector Dia. (mm) 0.95 & 0.45

JZY-B272

φ9.5mm special gas rubber gasket

(G1/2 inch special metal gasket)

”

Rated gas pressure

Nominal heat input

Hoop

Red thread

Hose connector

Rubber hose

Gas inlet of stove

Rubber washer

Metal corrugated pipe

Rubber washer

Front valve

Rubber hose diagram A schematic diagram of a metal bellows

Gas Hob Gas Hob

910

Bottom functional location diagram

Use Instruction

1. Be sure the copper core, copper cover, copper base and pan stand in right

position. Check the switch first before turn on the valve of the gas. (Pic1)

2. IGNITION METHOD: Push the switch and turn to 90 degrees anti-clockwise for the

strongest flame, (Pic2) meanwhile the poop sound of pulse firing can be heard. The

full push should be taken for 3-5 seconds till the flame comes out. Otherwise, the

same operation above should be retaken. In addition, push the switch and turn to 90

degrees anti-clockwise again is the small flame. (Pic3)

Remark: The device shall not be operated for more than 15 s. If after 15 s the burner

has not lit, stop operating the device and open the compartment, door and/or wait at

least 1 min before attempting a further ignition of the burner.

Battery installation position

The position of the air inlet of the stove

360

370

380

390

400

710

700

690

680

670

660

400

390

380

370

360

710

700

690

680

670

660

7. The range of openings that this cooker can adapt to is:

Length 650mm-710mm, width 350mm-400mm;

For replacement installation, the installation method is as follows:

①First, the installer measures the actual size of the user's home opening;

②Wipe the chassis scale area with a clean cloth, and then paste the limit bars (four)

to the corresponding ones as shown in the figure below

Position, the outer edge is aligned with the corresponding tick line. After pasting,

press the limit bar hard to make it tightly fit (by company professionals

Installation).

③Put the product with good limit strips into the opening, pay attention to the need

for leveling the cooker after placing, and ensure that each limit strip is embedded in

the opening.

It is recommended to use the product after 24 hours to ensure that the adhesive is

cured.

Cooker opening adjustment scale (length) Cooker opening adjustment scale (width)

Take the measured opening size 700 × 400 as an example

The outer edge of the

limit bar is aligned with

the scale line 700

Limit bar outer

edge alignment

scale line 400

Note: Both sides are pasted

in the same way

1. Maintain gas hob surface: Please clean the surface with wet and neutral detergent

cloth, and then clean with dry cloth, Don’t use steel brush or other rigidity objects.

2. Check if the copper cover, copper core and ornamental ring are shift or biasing,

and correct them at the right position in time.

3. Please deal with used battery properly avoiding pollution.

4. This product use environmental and recyclable package, please deal with those

packages properly in order to protect environment and reduce waste.

5. If maintenance confirms this product can’t be used again, please deal with

recyclable materials properly.

6. In order to keep ordinary usage and good combustion regime, operator must clean

and dredge the fire hole with brush and steel needle regularly to prevent fire from

turning back and damage gas hob. Don’t bath this product.

Flame port on internal cap

Inner-ring flame port of external cap

Flame port on external cap

Clean and Maintenance

Gas Hob Gas Hob

11 12

Normal

(Full Combustion)

Yellow Flame

(Air deficiency)

Floating Flame

(Air superabundant)

Combustion well: the flame takes on cyanine, no yellow flame or red fire, the

interior and exterior flame is clear.

Air deficiency: the flame is stretched and takes on yellow or red, the interior and

exterior flame is faintly.

Air superabundance: the flame is unstable, about to leave the fire cover or flame

becomes short obviously (sometimes will occur backfire when using manufactured

gas), and color of flame appear cyan.

REMARKS: The first ignition or that of the first reuse of the gas stove may not work

immediately, because there is air in the tube, it needs to be operated repeatedly.

3. SWITCH-OFF: Turn the switch to the position clockwise (Pic1) and the fire will be

switched off.

4. FIREPOWER CONTROL: Operate according to the instruction mark.

swtich off position strongest

flame position weakest flame position

Pic1 Pic2 Pic3

5. Airflow control: Please adjust the inlet airflow, to make the gas fully fired.

Adjust the inlet spot nail or plate (at the bottom of hobs), by clockwise or anti

clockwise, till the flame become stable and blued colored (as following picture). Here

is the way to differ the combustion states:

(The figure is provided for reference

only and subject to the actual product.)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Quemador de Robam

Robam

Robam B396 Series Manual de usuario

Robam

Robam JZY-B394 Manual de usuario

Robam

Robam JZY-B928 Manual de usuario

Robam

Robam JZT B110 Manual de usuario

Robam

Robam JZ-B312 Manual de usuario

Robam

Robam JZ(Y/T)-G413 Manual de usuario

Robam

Robam JZ-B594 Manual de usuario

Robam

Robam JZY-ZB61H70 Manual de usuario

Robam

Robam CS46-W270 Manual de usuario

Robam

Robam HS44-W211 Manual de usuario

Robam

Robam JZY-B594 Manual de usuario

Robam

Robam JZY-B398 Manual de usuario

Robam

Robam cd28-w985 Manual de usuario

Robam

Robam JZ-B715 Manual de usuario

Robam

Robam JZY-B920 Manual de usuario

Robam

Robam JZY-G370 Manual de usuario

Robam

Robam JZT-B291 Instrucciones de montaje

Manuales populares de Quemador de otras marcas

Siemens

Siemens EX875KYV1E Hoja de especificaciones

AEG

AEG CERAMIC HOB 6010 K Manual de usuario

VALERA

VALERA CT 70A Manual de usuario

Zanussi

Zanussi ZGF 6420 Manual de usuario

Gaggenau

Gaggenau CI 273 Manual de usuario

G3 Ferrari

G3 Ferrari Energy Manual de usuario

Pkm

Pkm IN4B Manual de usuario

Award

Award H903BG Manual de usuario

Zanussi

Zanussi VCH 5005 RZ Manual de usuario

Miele

Miele KM 523 Manual de usuario

Hotpoint

Hotpoint IS67V8CCXT/E Manual de usuario

AEG

AEG HK854870XB Manual de usuario

Cookology

Cookology SEP600BK Manual de usuario

Bauknecht

Bauknecht Hob Manual de usuario

Zanussi

Zanussi ZGM 782 Manual de usuario

dipo INDUCTION

dipo INDUCTION DIBK218S Manual de usuario

Miele

Miele KM 5987 Manual de usuario

Miele

Miele KM 360 G Manual de usuario