Roadstar DVD-2010H Manual de usuario

SERVICE MANUAL

Roadstar

DVD-2010H

1. GENERAL DESCRIPTION

Major functional blocks are discussed briefly in this section. A more detailed description is contained later in the

document.

1.1 STi5519

The STi5519 provides a highly integrated back end solution for DVD applications. A host CPU handles

both the general application (the user interface, and the DVD, CD DA, VCD, SVCD navigation) and the

drivers of the different embedded peripheral (audio/video, sub picture decoders, OSD,

PAL/NTSC encoder...)

These functions include:

Integrated 32 bit host CPU @ 60MHz

2 Kbytes of instruction cache, 2 Kbytes of data cache, and 4Kbytes of SRAM configurable as

data cache.

Audio decoder

5.1 channel Dolby Digital® /MPEG 2 multi channel decoding, 3 X 2 channel PCM outputs

IEC60958 IEC61937 digital output

DTS® digital out 5.1 channel

SRS®/TruSurround®

MP3 decoding

Video decoder

Supports MPEG 2 MP@ML

Fully programmable zoom in and zoom out

PAL to NTSC and NTSC to PAL conversion

DVD and SVCD subpicture decoder

High performance on screen display

to 8 bits per pixel OSD options

Anti flicker, anti flutter and anti aliasing filters

PAL/NTSC/SECAM encoder

RGB, CVBS, Y/C and YUV outputs with 10 bit DACs

Macrovision® 7.01/6.1 compatible

Shared SDRAM memory interface

Supports one or two 16Mbit, or one 64Mbit 125 MHZ SDRAMs

Programmable CPU memory interface for SDRAM, ROM, peripherals...

Front end interface

DVD, VCD, SVCD and CD DA compatible

Serial, parallel and ATAPI interfaces

Hardware sector filtering

Integrated CSS decryption and track buffer

Integrated peripherals

UARTS, 2 SmartCards, I2C controller, 3 PWM outputs, 3 capture timers

Modem support

38 bits of programmable I/O

Please refer to the STi5519 Data Sheets: STi5519 DVD HOST PROCESSOR WITH ENHANCED

AUDIO FEATURES and STi5519 REGISTER MANUAL for more detailed information.

1. MEMORY

The STi5519 includes all of the interface signals to connect to industry standard SDRAM, DRAM, ROM, and I2C

memory devices. The system includes one or two SDRAM components. The MPEG decoder unit interfaces to a single

4M x 16bit SDRAM over the SMI bus. The general purpose processor can share the decoder SDRAM or can access

an optional SDRAM installed on the EMI bus. This EMI SDRAM can be either a 1Mx16 or 4Mx16 chip. The optional

EMI SDRAM can be installed if the system requires higher performance of requires more RAM than is standard

system (due to complex trick modes, advanced GUI, etc). The standard production executes without EMI SDRAM

installed, A single 1Mx16 FLASH ROM device is support on the EMI bus. There is also a 2kb I2C serial EEPROM

for storage of user player settings, software configuration information, title specific information, or other purposes.

1.3 DRIVE INTERFACES

The system supports a standard ATAPI drive interface.

The interface to the ATAPI drive is included within the STi5519. The ATAPI data bus is buffered so that the ATAPI

cable does not interfere with signal quality. An ATAPI drive is connected via the standard 34 pin dual row PC style IDE

header

1.4 FRONT PANEL

The front panel is based around an Futaba VFD and a common NEC front panel controller chip, (uPD16311). The

STi5519 controls the uPD16311 using several control signals, (clock, data, chip select). The infra red remote control

signal is passed directly to the STi5519 for decoding.

1.5 OUTPUTS

There is no separate rear panel for outputs. They are embedded into the mainboard. Supported outputs are:

Six channel or two channel audio outputs

Optical and coax S/PDIF outputs are supported

Composite, S Video, and SCART outputs

The six video signals used to provide CVBS, S Video, and RGB are generated by the STi5519's internal video DAC.

The video signals are be buffered by external circuitry.

Six channel audio output by the STi5519 in the form of three I2S (or similar) data streams. The S/PDIF serial stream is

also generated by the STi5519. Three pieces two channel audio DACs (CS4335) are used for six channel audio

output, and similarly only one CS4335 DAC is used for two channel audio output.

GPIO, IRQ, AND CHIP SELECT ASSIGNMENTS

PIO Port Bit Pin # STi5519 Alternate Function Software Function

P in data

208

207

206

205

204

203

202

201

200

199

198

197

196

195

194

193

192

191

190

189

188

187

186

185

184

183

182

181

180

179

178

177

176

175

174

173

172

171

170

169

168

167

166

165

164

163

162

161

160

159

158

157

P IO 2[4]

P IO 2[3]

P IO 2[2]

P IO 2[1]

P IO 2[0]

T R IG G E R _ OUT

T R IG G E R _ IN

P IO 1[5]

P IO 1[4]

V S S

VDD2_ 5

P IO 1[3]

P IO 1[2]

P IO 1[1]

P IO 1[0]

P IO 0[7]

P IO 0[6]

P IO 0[5]

P IO 0[4]

P IO 0[3]

P IO 0[2]

P IO 0[1]

P IO 0[0]

V S S

VDD3_ 3

C P U _A DR [21]

C P U _A DR [20]

C P U _A DR [19]

C P U _A DR [18]

C P U _A DR [17]

C P U _A DR [16]

C P U _A DR [15]

C P U _A DR [14]

C P U _A DR [13]

C P U _A DR [12]

C P U _A DR [11]

V S S

VDD2_ 5

C P U _A DR [10]

C P U _A DR [9]

C P U _A DR [8]

C P U _A DR [7]

C P U _A DR [6]

C P U _A DR [5]

C P U _A DR [4]

C P U _A DR [3]

C P U _A DR [2]

C P U _A DR [1]

V S S

VDD3_ 3

C P U _DATA [15]

C P U _DATA [14]

P IO 2[5]

P IO 2[6]

P IO 2[7]

V DD3_3

V S S

P IO 3[0]

P IO 3[1]

P IO 3[2]

P IO 3[3]

P IO 3[4]

P IO 3[5]

P IO 3[6]

P IO 3[7]

V DD2_5

V S S

B _DATA

B _B C L K

B _F L AG

B _S Y N C

P IO 5[0]

P IO 5[1]

P IO 5[2]

V DD_ R G B

V S S _ R G B

B _O UT

G _O UT

R _OUT

V_R E F _R G

I_R E F _R G

V DD_Y C C

V S S _Y C C

Y _O UT

C _OUT

C V _OU T

V _ R E F _Y C

I_R E F _Y C

V DD2_5

V S S

P IO 4[0]

P IO 4[1]

P IO 4[2]

P IO 4[3]

P IO 4[4]

P IO 4[5]

P IO 4[6]

P IO 4[7]

V DD3_3

V DD _P C M

V S S _ P C M

V S S

DAC _S C LK

DAC _P C MOUT 0

156

155

154

153

152

151

150

149

148

147

146

145

144

143

142

141

140

139

138

137

136

135

134

133

132

131

130

129

128

127

126

125

124

123

122

121

120

11 9

11 8

11 7

11 6

11 5

11 4

11 3

11 2

111

11 0

109

108

107

106

105

C P U_DATA[13]

C P U_DATA[12]

C P U_DATA[11]

C P U_DATA[10]

C P U_DATA[9]

C P U_DATA[8]

V S S

V DD2_5

C P U_DATA[7]

C P U_DATA[6]

C P U_DATA[5]

C P U_DATA[4]

C P U_DATA[3]

C P U_DATA[2]

C P U_DATA[1]

C P U_DATA[0]

C P U_C AS 1

C P U_C AS 0

C P U_R AS 1

V S S

V DD3_3

C P U_C E [0]

C P U_C E [1]

C P U_C E [2]

C P U_C E [3]

C P U_WAIT

C P U_R W

C P U _B E [1]

C P U _B E [0]

IR Q [0]

IR Q [1 ]

IR Q [2 ]

R E S E T

V S S _ P L L

V DD_P L L

V S S

P IX _C L K

V DD2_5

C P U_P R O C LK

C P U_OE

P WM0

P WM1

P WM2

T C K

T DI

T DO

T MS

T R S T

V S S

V DD3_3

res erved

P IO5[5]

DAC _P C MOUT 1

DAC _P C MOUT 2

DAC _ PC MC L K

DAC _LR C L K

S P D IF _O U T

S MI_ADR [4]

S MI_ADR [5]

S MI_ADR [6]

S MI_ADR [7]

S MI_ADR [8]

S MI_ADR [9]

VDD2_5

V S S

S MI_ADR [3]

S MI_ADR [2]

S MI_ADR [1]

S MI_ADR [0]

S MI_ADR [10]

S MI_ADR [11]

S MI_ADR [12]

S MI_ADR [13]

S MI_C S [0]

S MI_C S [1]

S MI_R AS

S MI_C AS

S MI_WE

S MI_D Q ML

S MI_D Q MU

VDD3_3

S MI_C LK IN

V S S

S MI_DATA[0]

S MI_DATA[1]

S MI_DATA[2]

S MI_DATA[3]

S MI_DATA[4]

S MI_DATA[5]

S MI_DATA[6]

S MI_DATA[7]

S MI_DATA[8]

S MI_DATA[9]

VDD2_5

S MI_C L K O U T

V S S

S MI_DATA[1 0]

S MI_DATA[11]

S MI_DATA[1 2]

S MI_DATA[1 3]

S MI_DATA[1 4]

S MI_DATA[1 5]

P IO5[3]

P IO5[4]

100

101

102

103

104

P QF P 208

(rev F )

S Ti5519

PIO Port Bit Pin # STi5519 Alternate Function CineMaster CE Function

Port 0 Bit 0

Port 0 Bit 1

Port 0 Bit 2

Port 0 Bit 3

Port 0 Bit 4

Port 0 Bit 5

Port 0 Bit 6

Port 0 Bit 7

186

187

188

189

190

191

192

193

SC0_DATA

#ATAPI_RD

#ATAPI_WR

SC0_CLK

SC0_RST

SC0_CMD_VCC

SC0_DATA_DIR

SC0_DETECT

#SOFT_RESET

#ATAPI_RD

#ATAPI_WR

DAC_CCLK (Audio DAC control)

DAC_CDTI (Audio DAC control)

#DAC_CS0 (Audio DAC control)

#DAC_CS1 (Audio DAC control)

Unused (Test Point 39)

Port 1 Bit 0

Port 1 Bit 1

Port 1 Bit 2

Port 1 Bit 3

Port 1 Bit 4

Port 1 Bit 5

Port 1 Bit 6

Port 1 Bit 7

194

195

196

197

200

201

202

203

SSC0_DATA

SSC0_CLK

PARA_DVALID/SC_EXT_CLK

TXD2

RXD2

PARA_SYNC/TXD1

TRIGIN

TRIGOUT

SDA (I2C)

SCL (I2C)

Unused (Test Point 35)

TXD (Serial Port)

RXD (Serial Port)

SR0 (for PLL1700)

TRIGIN (JTAG)

TRIGOUT (JTAG)

Port 2 Bit 0

Port 2 Bit 1

Port 2 Bit 2

Port 2 Bit 3

Port 2 Bit 4

Port 2 Bit 5

Port 2 Bit 6

Port 2 Bit 7

204

205

206

207

208

SC1_DATA

PARA_REQ/RXD1

PARA_STR

SC1_CLK

SC1_RST

SC1_CMD_VCC

DAC_DATA/SC1_DATA_DIR

SC1_DETECT

FPCLK (Front Panel)

FS0 (for PLL1700)

FS1 (for PLL1700)

RTS (Serial Port)

CTS (Serial Port)

FPDATA (Front Panel)

DAC_DATA (Stereo Audio)

FPSTRB (Front Panel)

Port 3 Bit 0

Port 3 Bit 1

Port 3 Bit 2

Port 3 Bit 3

Port 3 Bit 4

Port 3 Bit 5

Port 3 Bit 6

Port 3 Bit 7

PARA_DATA0

PARA_DATA1

PARA_DATA2

PARA_DATA3

PARA_DATA4

PARA_DATA5

PARA_DATA6/COMP1

PARA_DATA7/COMP2

OPEN (TMM Tray Control)

CLOSE (TMM Tray Control)

Unused (Test Point 36)

Front Panel IR

Unused (Test Point 37)

Unused (Test Point 38)

#SENSE (TMM Tray Control)

#PUSH (TMM Tray Control)

Port 4 Bit 0

Port 4 Bit 1

Port 4 Bit 2

Port 4 Bit 3

Port 4 Bit 4

Port 4 Bit 5

Port 4 Bit 6

Port 4 Bit 7

YUV0

YUV1

YUV2

YUV3

YUV4

YUV5

YUV6

YUV7

YUV0 (External Video DENC)

YUV1

YUV2

YUV3

YUV4

YUV5

YUV6

YUV7

* Front Panel uses the 16311 controller. In the CineMaster design, FPDIN and FPDOUT are connected

together as FPDATA.

3. AUDIO OUTPUT

The STi5519 supports a six channel analog output. In a system configuration with six analog outputs, the front left and

right channels can be configured to provide the stereo 2 channel) outputs and Dolby Surround, or the left and right front

channels for a 5.1 channel surround system.

The Sti5519 also provides digital output in S/PDIF format. The board supports both optical and coaxial S/PDIF outputs.

3.1 AUDIO DACS

The STi5519 supports several variations of an I2S type bus, varying the order of the data bits leading or no leading zero

bit, left or right alignment within frame, and MSB or LSB first) is possible using the Sti5519 internal configuration regis-

ters. The I2S format uses four stereo data lines and three clock lines. The I2S data and clock lines can be connected

directly to one or more audio DAC to generate analog audio output.

The two-channel DAC is an Cirrus Logic CS4335. The DACs support up to 96kHz sampling rate.

The outputs of the DACs are differential, not single ended so a buffering circuit is required. The buffer circuits use National

LM833 op-amps to perform the low-pass filtering and the buffering.

4 VIDEO INTERFACE

The STi5519 integrates a PAL/NTSC encoder. It converts the digital MPEG/Sub Picture/OSD

stream into a standard analog baseband PAL/NTSC signals. Six analog video outputs provide CVBS, Svideo Y/C), and

RGB formats. The three RGB signals can be configured via an internal STi5519 register setting.

The encoder handles interlaced and non-interlaced mode. It can perform Closed Captions, CGMS or Teletext encoding

and allows Macrovision 7.01/6.1 copy protection. The encoder supports both master and slave modes for synchroniza-

tion.

The buffered CVBS video is available on a RCA cinch) style jack, S-Video on a mini-DIN and all six signals and stereo

audio) are available on a SCART connector.

5 MPEG DECODER SDRAM MEMORY

The STi5519 includes glueless interfaces to SDRAM memory for the MPEG decoder. The STi5519 supports one or two

1Mx16bit chips or a 4Mx16bit SDRAM chip. However, the board

supports only a 64Mbit chip. The device used is a 4M x 16 bit, 125MHz, 3.3V, 54 pin TSOP II, Micron Technology

MCT48LC4M16A2TG-7 or equivalent.

6 FLASH MEMORY

The decoder board supports a single 1Mx16bit FLASH memory device. The device is a 1M x 16, 90ns, bottom boot

block, 3.3V, 48 pin TSOP II, 29F800 or equivalent.

7 SERIAL EEPROM MEMORY

An I2C serial EEPROM is used to store user configuration i.e. language preferences, speaker setup, etc.) and software

configuration information i.e. remote control type). Industry standard EEPROM range in size from 1kbit to 256kbit and

share the same IC footprint and pinout. The default device is 2kbit, 256kx 8, SOIC8 SGS Thomson ST24C02M1 or

equivalent.

8 ATAPI DRIVE INTERFACE

The STi5519 includes a glueless ATAPI interface on-chip. While this interface limits performance of the system, it is a

lower cost solution than providing external logic to interface the drive to the STi5519 frontend interface.

Note: The decoder board supports the standard ATAPI electrical connections, but the software protocol within the drive is

not always supported according to ATAPI specifications. Custom software may need to be developed and tested to

support ATAPI drives from different manufacturers.

9 AUDIO SAMPLING RATE AND EXTERNAL PLL COMPONENT CONFIGURATION

The decoder board has optional PLLs, which can be installed to provide the audio clock for the system. The initial version

of the STi5505 was not able to provide an audio clock for 96kHz support and an external PLL was used to support this.

This was fixed in the STi5505 later chip revisions and therefore no problems are expected in the STi5519. However, in

case a problem arises, the PLL circuit can be installed to provide a high quality clock  particularly important in S/PDIF

applications.

In the default configuration, a small buffer chip is installed to buffer the audio clock between the STi5519 and the audio

DACs.

10 FRONT PANEL

10.1 VFD CONTROLLER

The VFD controller is a NEC uPD16311. This controller is not a processor, but does include a simple state machine

which scans the VFD and reads the front panel button matrix. The 16311 also includes RAM so it can store the current

state of all the VFD icons and segments. Therefore, the 16311 need only be accessed when the VFD status changes and

when the button status is read. The STI5519 can control this chip directly using PIO pins or can allow the front panel PIC

to control the VFD.

11 MISCELLANEOUS FUNCTIONS

11.1 RESET CIRCUITRY

Two different chips are supported to provide the power-on-reset and pushbutton reset function:

Telcom Semiconductor TC1270, or Dallas DS1811.

11.2 VOLTAGE REGULATORS

There are two +5V linear regulators to generate +5V for the analog circuitry from +12V. A smaller DPAK surface mount

device can be used in most circumstances, but in applications were more than 150mA are required, a TO-220 through-

hole package can be used.

The STi5519 requires 2.5V to operate. This voltage is generated from +5V.

12 CONNECTORS

12.1 ATAPI DRIVE STANDARD CONNECTOR

12.2 STI5519 JTAG INTERFACE

12.3 SCART CONNECTORS

12.4 POWER CONNECTOR

13. VESTEL DVD DECODER CIRCUIT DESCRIPTION

13.1 POWER SUPPLY

·Socket PL1 is the 220VAC input.

·Socket PL4 is used for the power button on the front panel.

·2.5A fuse 1 is used to protect the device against short circuit.

·Line filters and capacitors TR2, C2, TR4 and C3 are used to block the parasitic coming from the

mains. They also prevent the noise, produced in the circuit, from being injected to the line.

·Voltage is rectified by using diodes D1, D5, D6 and D4. Using capacitor C1 (100mf) a DC voltage

is produced. (310- 320VDC).

· The current in the primary side of the transformer TR3 comes to the SMPS IC (IC3 TOP223Y). The

SMPS IC has a three-pin TO-220 case and a cooler is mounted on it. It has a built-in oscillator,

overcurrent and overvoltage protection circuitry and runs at 100kHz. It starts with the current from

the primary side of the transformer and follows the current from the feedback winding.

·eedback current is rectified with diode D7 and filtered with capacitor C4 and enters the

optocoupler IC2 (CQY80NG). Depending on the control current coming from the secondary side,

SMPS IC keeps the output voltage constant by controlling the duty cycle of the 100kHz signal

(PWM) at the primary side of the transformer.

· Voltages on the secondary side are as follows: -12 Volts at D8, 5 Volts at D9, 15 Volts at D10, -

22 Volts at D13.

·Using resistors R5, R4 and R27, 5V output is divided properly for D14 operation.

·D14 TL431 is a constant current regulator. TL431 watches the 5 volts and supplies the required

current to IC2. There are a LED and a photo transistor in IC2. The LED inside the IC2 transmits the

value of the current from D14 to phototransistor. Depending on the current gain of the

phototransistor IC3 keeps the voltage on the 5-volt-winding constant.

·Adjustable voltage regulator IC5 (LM317) supplies 12 Volts. 12 Volts is obtained by using resis-

tors R19, R20 and R21.

·When the device enters stand-by mode, transistor Q2 starts to conduct and pulls the adjust pin of

IC5 to ground, where this cuts 12Volts off.

·IC6 is also an LM317 that produces 3.3 Volts output from its 5 volts input.

·22 Volts is used to feed the V D (Vacuum luorescent Display) driver IC on the front panel.

Using diode D17 22V is decreased about 5.6V and connected to the filament winding to pro-

duce the DC offset for the filaments.

·Transistor Q3 and zener diode D18 are used to regulate +12 Volts. This voltage is used to feed

op-amps on the back panel.

TOP

221

227

TOPS

witch

lin

Figure 1. Typical Flyback Application.

easier. The standard 8L PDIP package option reduces cost in

lower power, high efficiency applications. The internal lead

frame of this package uses six of its pins to transfer heat from

thechipdirectlytotheboard,eliminatingthecostofaheatsink.

TOPSwitch incorporates all functions necessary for a switched

modecontrolsystemintoathreeterminalmonolithicIC:power

MOSFET, PWM controller, high voltage start up circuit, loop

compensation and fault protection circuitry.

odu

ighligh

Lowest cost, lowest component count switcher solution

Cost competitive with linears above 5W

Very low AC/DC losses Ðup to 90% efficiency

Built-in Auto-restart and Current limiting

Latching Thermal shutdown for system level protection

Implements Flyback, Forward, Boost or Buck topology

Works with primary or opto feedback

Stable in discontinuous or continuous conduction mode

Source connected tab for low EMI

Circuit simplicity and Design Tools reduce time to market

e c

ion

The second generation TOPSwitch-II family is more cost

effective and provides several enhancements over the first

generationTOPSwitchfamily. TheTOPSwitch-IIfamilyextends

the power range from 100W to 150W for 100/115/230 VAC

input and from 50W to 90W for 85-265 VAC universal input.

This brings TOPSwitch technology advantages to many new

applications, i.e. TV, Monitor, Audio amplifiers, etc. Many

significant circuit enhancements that reduce the sensitivity to

board layout and line transients now make the design even

PI-1951-091996

TOPS

witch

13.2 FRONT PANEL

·All the functions on the front panel are controlled by U1 (Sti5519) on the mainboard.

·U1 sends the commands to IC2 uPD16311 via socket PL1 (pins 3,4 and 5).

·There are 16 keys scanning function, 2 LED outputs, 1 Stand-by output and V D drivers on IC2.

·Pin 52 is the oscillator pin and is connected via R5 56K.

·LED D6 is red in stand-by mode and green when the device is on. When entering stand-by mode,

pin 48 goes HIGH (+5V) and controls the transistor Q2 on the power board.

·Vacuum fluorescent display MD2 is specially designed for DVD.

·The scanned keys are transmitted via IC2 pin 5 and 6 to U1 on the mainboard.

·IR remote control receiver module IC3 (TSOP1836) sends the commands from the remote control

directly to U1.

·Socket PL2 carries the V D filament voltage and 22 Volts.

13.3 Outputs

·There are 1 SCART connector (PL5), 6 pieces RCA audio jacks JK1, for audio output, 1 coaxial

digital audio output JK3 and 1 laser digital audio output MD1 on the back panel.

·TOTX178 is used for laser output.

·SPDI enters the pins 1,3,5,9, and 11 of IC25. Connecting gates in parallel a buffer is constructed.

C166 is used for DC coupling. Resistors R181 and R182 divide the signal, which is transmitted

out via JK3 (RCA jack)

· Audio outputs are on JK1.

·Q145 through Q148 are used to suppress the noises during turn on and turn off.

· There are two op-amps in each IC18, IC19 and IC20 and they are used for six audio channels.

IC18 is used for front channels, Resistors R137,R190 and R158 are used to adjust the gain and

using R156 and C116 a filter circuit is created for the left channel. or front right channel, these

components are R140, R191 and R149 for gain, R151 and C113 for filter. or the remaining four

channels IC19 and IC20 are used with the corresponding resistors and capacitors connected in

similar way.

·Op-amp outputs the front left audio via C124 and R162 to RCA jack and via C123 and R161 to

SCART. ront right audio is sent to RCA its jack via C127, R164 and sent to SCART via C126

and R163.

·SCART pin 8 is controlled using transistors Q21 and Q22 to switch between modes 4:3 and 16:9 .

·When the BPPIO0 becomes 5 Volts, 4:3 mode is selected and 16:9 mode is selected when this

output becomes 0. The circuit is adjusted to output 12 Volts for 4:3 mode and 6 Volts for 16:9

mode.

·Transistors Q26 and Q24 transmits these voltages when the device is turned on and cuts them off

when the unit is turned off.

·LUMA and CHROMA signals of S-Video are transmitted to JK4 (S-Video socket) via transistors

Q12 and Q13 respectively.

COMPONENT

CODE MATERIAL UNIT QTY

20071874 MAINBOARD CHS. DVD-3000 (MAN) DVS-2CH PC 1.000 .....

20071876 POWER BOARD CHS.DVD-3000 (MAN)(5508-DVS) PC 1.000 .....

20092998 SCART ASSY DVD-3000 (MAN) (FERRITE') PC 1.000 .....

20100796 FRONT PANEL DVD3000 (MAN) (SC FERRITE') PC 1.000 .....

30000158 CAP MKP 4.7NF 630V J PC 1.000 C28 . . . .

30000423 CAP EL 47UF 400V M PC 1.000 C1 ....

30001155 RES MO 2W 33K J PC 1.000 R18 . . . .

30001284 DIODE 1N4148 0.15A/100V 0.5A PC 1.000 D7 ....

. . PC 4.000 D1 D2 D3 D4 .

30001302 DIODE BYW29-200 8A/200V 80A PC 1.000 D9 ....

30001318 DIODE BA159 1A/800V 20A PC 3.000 D8 D13 D16 . .

30001329 DIODE 1N4007 1A/1000V 30A PC 4.000 D1 D4 D5 D6 .

30001343 DIODE ZENER 5.6V PC 1.000 D17 . . . .

30001350 DIODE ZENER 12V PC 1.000 D18 . . . .

30001453 TR BC337 PC 1.000 Q3 ....

30001454 TR BC548B PC 1.000 Q2 ....

30001503 IC CQY80NG (OPT.COUPLER) PC 1.000 IC2 ....

30001506 IC TL431 PC 1.000 D14 . . . .

30001731 FUSE 2.5A 250V 5*20MM PC 1.000 F1 ....

30010501 R/C DVD (BLACK) PC 1.000 .....

30010700 DIODE BYV28-200 3.5A/200V 90A PC 1.000 .....

30010798 IC TOP223Y PC 1.000 IC3 ....

30011787 POWER CORD ASSY.(2.4MT W/FTZ)-SATELLITE- PC 1.000 .....

30012923 DVD LOADER (ATAPI INTERFACE) PC 1.000 .....

30012968 CONN ASSY 4/20 POWER (5.00 mm) PC 1.000 .....

30014124 IC 74LVX245 PC 2.000 .....

30015742 CONN ASSY 5P 15cm FLAT PC 1.000 .....

30016022 SWITCH TACT VERTICAL T&R PC 15.000 SW1 SW10 SW11 SW12 SW13

. . . . SW14 SW15 SW16 SW2 SW3

. . . . SW5 SW6 SW7 SW8 SW9

30016833 IC LM317T-2 PC 1.000 IC6 ....

. . PC 1.000 .....

30016836 CONN ASSY 6P 23cm W/FERRITE PC 1.000 .....

30017144 CONN ASSY 8P 30CM W/FERRRITE (TMM) PC 1.000 .....

30017992 CONN ASSY 40P 22CM (IDE CABLE) PC 1.000 .....

30018125 CONN ASSY 10P 12CM W/FERRITE CORE W/B PC 1.000 .....

40009968 PLASTIK AYAK DVD2200+DVB (SÝYAH) PC 4.000 .....

40009969 PLASTIK AYAK PÝMÝ (SÝYAH) PC 4.000 .....

POSITION NUMBER

2CHMP3-3000

SPARE PART LIST

NOTE: YOU CAN FIND SPARE PART CODES FOR MODEL- DEPENDENT PARTS IN OUR SERVICE WEB SITE : www.vestelservice.com

Tabla de contenidos

Otros manuales de Reproductor de DVD de Roadstar

Roadstar

Roadstar DVD-5111 Manual de usuario

Roadstar

Roadstar DVD-2020H Manual de usuario

Roadstar

Roadstar DVD-3205P Manual de usuario

Roadstar

Roadstar DVD-2017H Manual de usuario

Roadstar

Roadstar DVD-2000H Manual de usuario

Roadstar

Roadstar DVD-2000H Manual de usuario

Roadstar

Roadstar DVD-5102PSPK Manual de usuario

Roadstar

Roadstar DVD-7000 Manual de usuario

Roadstar

Roadstar DVD-2020H Manual de usuario

Roadstar

Roadstar DVD-3650H/N Manual de usuario

Roadstar

Roadstar VCD-4510 Manual de usuario

Manuales populares de Reproductor de DVD de otras marcas

Sony

Sony DVP-F11 Manual de usuario

Philips

Philips DVP3560K/F8 Manual de usuario

LENCO

LENCO DVP-740 X2 Manual de usuario

JVC

JVC XV-N650BEU Manual de usuario

Aiwa

Aiwa XD-DV370 Manual de usuario

MedeaWiz

MedeaWiz Sprite 4K DV-S4 Manual de usuario

Denon

Denon DVM-1805 - DVD Changer Manual de usuario

Toshiba

Toshiba SD-3815 Manual de usuario

Tevion

Tevion 44330 Manual de usuario

Samsung

Samsung DVD-HD860 Manual de usuario

Sylvania

Sylvania DP170SL8 Manual de usuario

Toshiba

Toshiba SD-P1200 Manual de usuario

JVC

JVC XV-D9000E Manual de usuario

Dolby Laboratories

Dolby Laboratories CP650 Manual de usuario

Philips

Philips DVD737K/931 Manual de usuario

Denon

Denon DVD-5900 Manual de usuario

Philips

Philips DVD 951 Manual de usuario

Philips

Philips DVDR3460 Manual de usuario