Ro-Man R6100 Manual de usuario
1/ 15
R6100
User Manual
Welcome
Thank you for choosing the Roman headset. The Roman headset has a fashionable design, powerful functions, and is
highly compatible. It provides you with handsfree convenience in calling and listening music. The Roman headset is
your best choice in office and during traveling and driving.
Bluetooth Wireless Technology
With the Bluetooth wireless technology, you can connect the headset to its compatible communication devices
without using cables. The Bluetooth wireless connection allows you to use functions of a cell phone without holding
the cell phone against the headset, but the maximum distance between the two cannot exceed 10 meters (or 30
inches). The Bluetooth wireless connection may be interfered by obstacles (such as walls) or other electronic devices.
2/ 15
In some areas, use of the Bluetooth wireless technology may be subject to some constraints. Please consult your local
authority or service provider for details.
3/ 15
Quick Start
Thank you for purchasing the R6100 Bluetooth headset. Authoritative data indicates that distraction, making calls, or
leaving both hands off the wheel during driving are the major factors that bring potential safety hazards on the highways.
R6100 is a Bluetooth headset tailored for safe driving. With this headset, you can answer a call within 3 seconds after you
pick up the headset, and hangs up after you place back the headset. No any other operation is needed. This prevents drivers
from being distracted and leaving both hands off the wheel. The R6100 is a high-quality Bluetooth device equipped with the
high-end chip. The connection and signals are stable and reliable It delivers the following functions:
Pick up to answer and place back to release a call
Two power supply modes for uninterrupted power supply
Bluetooth base ensuring automatically attachment or reset
Compatible with 99% of the Bluetooth smart devices
DSP automatic noise reduction for free and smooth communication
Fast switching between the Active and Sleep modes
4/ 15
Intelligent 1-to-2 multipoint connection
Automatic re-connection
Four languages
Last call redialing
Point-to-point communication
The headset consists of the following components:
1. Red and blue indictors
2. Multi-function button (MFB)
3. Volume up/down button
4. Charging port
5. Earpiece and earhook
6. Microphone
7. Earphone
8. Vehicle-mounted base
9. Support
10. Silicon pad
11. Toggle switch
5/ 15
Fully charge the headset before using. For details about how to charge the headset, see "Charger and Battery" in this manual.
Meanwhile, choose the cell phone that is compatible with the headset or other Bluetooth devices to pair with the headset.
For details about pairing, see "Basic Operations".
Tip: Keep the headset away from your credit card or other magnetic storage media; otherwise, the stored information may
be lost due to demagnetization.
Basic Operations
○Powering on and Pairing: Turn down the toggle switch. The red and blue indicators blink at the same time for
three times. The voice prompt "The headset is powered on" is played on the earphone. Then, the voice prompt
"enter the pairing status" is played. If the Bluetooth version of the headset is earlier than V2.1, you need to enter the
pairing password "0000". The headset is automatically powered off if pairing is not completed within 150 seconds.
○Connecting: After successful paring with the cell phone, the headset is connected to the cell phone. The voice
prompt "Paring is completed and the headset is connected" is played. If you cancel pairing, the voice prompt
"Bluetooth disconnected" is played, and the headset enters the standby state.
6/ 15
○Automatic Re-Connecting: When powered on, the headset is automatically connected with the cell phone that the
headset has previously paired with.
○Releasing a Call: During a call, you can press the MFB button to release the call, and a buzz sound can be heard.
○Rejecting a Call: When there is an incoming call, you can press the MFB button for about 1 second. Then, a buzz
sound is heard, accompanied with the voice prompt "Call rejected".
○Call & Audio Switching: During a call, you can press the MFB button twice to switch between the call and the
audio service.
○Receiving a Call: When there is an incoming call, you can hear a voice prompt "You have an incoming call",
followed by the calling number. You can press the MFB button to answer the call.
○Last Number Redialing: In the standby state, you can press the MFB button for about 1 second. Then, a buzz
sound is heard, accompanied with the voice prompt "Last number redialed". You can press the MFB button again
to cancel the redialing.
○Anti-Lost Warning: The voice prompt "The headset is disconnected" is played, and the blue indicator blinks
quickly. About 5 minutes later, the headset enters the pairing state. (If the headset is held close to the cell phone
7/ 15
within 5 minutes, the headset is automatically reconnected to the cell phone.) The pairing lasts about 150 seconds. If
pairing fails within 150 seconds, the headset is automatically powered off. (Tests indicate that the displayed status of
the headset may vary with the brand and model of the cell phone when this function is used.)
○ Music On/Pause: Press the MFB button once to play music, and press again to pause the music.
○ Volume Up: Press the volume up button once to increase the volume by one grade. If the volume reaches the
maximum, the voice prompt "Maximum volume" is played.
○ Volume Down: Press the volume down button once to decrease the volume by one grade. If the volume reaches the
minimum, the voice prompt "Minimum volume" is played.
○ Previous: Press and hold the volume up button to go to the previous piece of music.
○ Next: Press and hold the volume down button to go to the next piece of music.
○ Three-Wall Calling: If a call is coming in during an on-going call, you can press the MFB button to hold the
current call and answer the new call, and press the MFB button again to continue the original call.
8/ 15
Press and hold the MFB button for about 1 second, the current call (A) is held, and the incoming call (B) is answered.
Press and hold the MFB button for about 1 second again, and A is recovered. You can repeat the same operation to
switch between A and
During a call, you can press the MFB button to end the current call and recover the other call.
○ Powering Off: In any state, you can turn up the toggle switch to power off the handset. The voice prompt "The
headset is powered off" is played.
○ Enable/Disable Voice Control: If you double-press the MFB button in the standby state, a buzz sound is heard,
and the voice prompt "Voice dialing" is played. Press the MFB button again, and the voice control function is
disabled. (It is assumed that your cell phone supports the voice control function.)
○ 1-to-2 Multipoint Connection: First, pair the headset with cell phone A, and disable the Bluetooth function of A.
Then, pair the headset with cell phone B, and enable the Bluetooth function of B. If your cell phone supports the
automatic re-connection function, the Bluetooth headset will be automatically connected to A. Alternatively, you can
press the headset to re-connect to A. At this time, the Bluetooth headset can be concurrently connected to A and B.
○ Intelligent Call Releasing: You only need to put the headset back to the charging base to release a call.
9/ 15
○ Intelligent Sleep Mode: If the headset battery is low or the headset is not in use, you can put the headset back to
the charging base, and the headset will enter the Sleep mode. Next time when you take the headset out of the
charging base, the headset is automatically powered on, and paired and connected to the cell phone.
○ Intelligent Call Answering: If there is an incoming call when the headset is mounted on the charging base, you only
need to take the headset out of the base to answer the call.
○ Switching Between Four Languages: In standby state, you can press and hold the MFB button and the volume up
button"+" at the same time for about 1 second to switch between four languages.
Charger and Battery
Before using any charger to charge this headset, check whether the specifications of the charger meet requirements.
The recommended output voltage of the charger is 5±0.25 V DC, and the recommended output current is 100 mA to
500 mA. An over-high charging voltage may damage the headset.
10 / 15
○ Warning: Use the recommended charger whenever possible. Use of other types of chargers may violate the
warranty terms of the equipment and results in danger. If the charging cable is delivered with the headset, connect
the cable to a CCC-certified charger or computer to charge the headset.
○ Charging the Battery
The headset use embedded charging battery that cannot be removed. Do not attempt to remove the battery from the
headset; otherwise, the headset may be damaged.
If the headset is not used in a long time, keep it in a cool and well-ventilated place, and charge the headset once every
two months.
1. If the red indicator on the headset blinks, and the low-voltage tone is heard, the headset battery is low. If the
headset continues to work, it may be automatically powered off. At this time, you need to charge the headset by
connecting the cable of the charger to the charging port on the headset.
2. You can connect the charger to an AC power socket or a vehicle-mounted charger for charging.
3. The red indicator is on when the headset is being charged. If the charging is not started yet, disconnect the headset
from the power socket, and reconnect the headset again. It takes about 2 hours to fully charge the headset. After
Tabla de contenidos
