Ritron XT Series Manual de usuario

SERIES

USER MANUAL

MODELS COVERED:

RQX-127-XT RQX-127-XT-KP RQX-127M-XT RQX-127M-XT-KP

RQX-127M-XT-CC RQX-127M-XT-GG RQX-127M-XT-GG-KP RQX-427-XT

RQX-427-XT-CC RQX-427-XT-GG RQX-427-XT-GG-KP RQX-427-XT-KP

RQX-127-XT-CANADA RQX-427-XT-CANADA

Ritron Pub. 14500099 Rev. B

07/23

GateGuard, Quiet Call and Quick Assist are registered trademarks of Ritron, Inc.

Quick Talk, Liberty and RadioNexus are trademarks of Ritron, Inc.

Call 800-USA-1-USA

For the right Wireless Solutions for your communication needs.

P.O. Box 1998 ·Carmel, Indiana 46082-1998 · Ph: 317-846-1201 · Fax: 317-846-4978

Email: ritron@ritron.com · www.ritron.com

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 0

ABLE OF

ONTENTS

...........................................................................

Basic Operation

XT-SERIES CALLBOX MODELS..................................................1

ABOUT THE XT-SERIES CALLBOX..............................................2

EXPOSURE TO RADIO FREQUENCY ENERGY...............................3

OPERATING THE XT-SERIES CALLBOX WITH

FACTORY DEFAULT SETTINGS ..................................................3

Installation Instructions

APPLYING POWER TO THE XT-SERIES CALLBOX.........................4

Using Internal Batteries.........................................................4

Using External +12 VDC Power with Battery Back-up .................5

Using External +12 VDC Power without Battery Back-up.............5

POWER MANAGEMENT OPTIONS ...............................................6

FIG-1

: Sensor Turn-On Jumper Shown in Turn-On Position

..............6

RELAY POLARITY JUMPER SETTING...........................................6

ANTENNA JUMPER SETTING.........................................................7

CALLBOX CONTROLS AND CONNECTORS ...................................8

FIG-2: Callbox Controls and Connectors .................................8

FIG-3: XT Callbox Assembly .......................................................9

CONNECTING TO THE XT ACCESSORY CABLE...........................10

XT-SERIES CALLBOX INSTALLATION INSTRUCTIONS ..................12

Field Programming

XT-SERIES FIELD PROGRAMMING OVERVIEW ..........................13

HOW TO FIELD PROGRAM FREQUENCY &TONE CODES.............14

TABLE 1:PROGRAMMABLE FREQUENCY CODES .......................15

CANADIAN FREQUENCY CODES...........................................16

TABLE 2:PROGRAMMABLE QC TONE CODES...........................16

TABLE 3:PROGRAMMABLE DQC TONE CODES ........................16

HOW TO FIELD PROGRAM 2-TONE,DTMF OR SELCALL DECODE

(RECEIVE)OPERATION ..........................................................17

TABLE 4:PAGING,GATEGUARD®AND LISTEN IN DECODE

CODES.................................................................................19

HOW TO FIELD PROGRAM DTMF OR SELCALL ENCODE ANI

(TRANSMIT)CODES ...............................................................21

HOW TO FIELD PROGRAM FEATURE CODES .............................22

TABLE 5: ADVANCED FEATURE CODES ....................................23

Programmable Features

PC PROGRAMMABLE XT-SERIES CALLBOX FEATURES..............25

Glossary of Terms..............................................................25

TABLE 6:PC PROGRAMMABLE FEATURES................................25

INTERCOM (ALWAYS-ON)PROGRAMMING ................................27

FEATURES TO USE WITH INTERCOM (ALWAYS-ON)

PROGRAMMING .....................................................................27

RELAY SWITCH OUTPUT OPTIONS (ALLOWS CONTROL OF AN

EXTERNAL DEVICE) ...............................................................28

2-TONE,DTMF OR SELCALL DECODE (RECEIVE)SETTINGS......29

Voice Messages

AUTOMATIC VOICE MESSAGES................................................30

AUTOMATIC IDRE-SEND........................................................31

HOW TO RECORD A VOICE MESSAGE ......................................32

HOW TO RECORD A VOICE MESSAGE USING .WAV AUDIO FILES .33

HOW TO PLAY A VOICE MESSAGE ...........................................34

HOW TO ERASE A VOICE MESSAGE.........................................34

GateGuard®Application

Configuration for the Remote Control of a Gate Controller

CONFIGURING THE CALLBOX FOR A GATEGUARD®APPLICATION 35

TABLE 7: XTACCESSORY CABLE............................................35

HOW TO FIELD PROGRAM THE XT-SERIES CALLBOX FOR

GATEGUARD®OPERATION.....................................................36

OPTIONAL GATEGUARD®SETTING/FEATURES..........................36

Licensing

FCC Licensing.......................................................................38

How to Obtain an FCC Radio License.......................................38

INDUSTRY CANADA Regulations............................................38

Safety Standards...................................................................38

Service.................................................................................38

Warranty

RITRON, INC. LIMITED WARRANTY .......................................39

THANK YOU FOR CHOOSING RITRON

Congratulations on your purchase of the RQX XT-Series Callbox. Your new radio is the culmination of RITRON’s 40 years of

designing, manufacturing, and supplying reliable, professional wireless communication products. Ritron wireless products will

improve the operation, safety, and profitability of any organization by providing instant voice communications between

employees throughout the workplace.

RQX XT-Series Wireless Callbox Basic Operation

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 1

XT-S

ERIES

ALLBOX

ODELS

..............................................................

XT-Series USA Models

RQX-127-XT .........................VHF Vandal-Resistant XT Callbox

RQX-127-XT-KP ....................VHF Vandal-Resistant XT Callbox with Keypad

RQX-127M-XT ......................MURS Vandal-Resistant XT Callbox

RQX-127M-XT-CC.................MURS Vandal-Resistant XT Callbox – Club Call

RQX-127M-XT-GG.................MURS Vandal-Resistant XT Callbox - GateGuard

RQX-127M-XT-GG-KP...........MURS Vandal-Resistant XT Callbox – GateGuard with Keypad

RQX-127M-XT-KP .................MURS Vandal-Resistant XT Callbox with Keypad

RQX-427-XT .........................UHF Vandal-Resistant XT Callbox

RQX-427-XT-CC....................UHF Vandal-Resistant XT Callbox – Club Call

RQX-427-XT-GG....................UHF Vandal-Resistant XT Callbox – GateGuard

RQX-427-XT-GG-KP..............UHF Vandal-Resistant XT Callbox – GateGuard with Keypad

RQX-427-XT-KP ....................UHF Vandal-Resistant XT Callbox with Keypad

XT-Series Canada Models

RQX-127-XT-CANADA..........VHF Canadian model Vandal-Resistant XT Callbox

RQX-427-XT-CANADA .........UHF Canadian model Vandal-Resistant XT Callbox

The XT-Series callbox is available in a Vandal-Resistant, High-Visibility Green.

The model number appears on the serial label located on the front of the interior plastic enclosure, behind the

removable faceplate.

VHF radios are designed to operate within the 15 MHz band between factory standard 150 and 165 MHz at

2W transmit power.

UHF radios are designed to operate within the 20 MHz band between factory standard 450 and 470 MHz at

1.5W transmit power.

MURS radios can only operate on the 5 MURS frequencies (151.820, 151.880, 151.940, 154.570, or 154.600

MHz) at 2W transmit power.

Advanced Features available with the XT-Series models include 2-Tone, DTMF and Selcall Decode, Voice

Messages, Companding, Sensor Input, and a Relay Switch Closure.

OPTIONAL ACCESSORY EQUIPMENT

Several options are available for the Ritron XT-Series Callbox. These options, individually, or in combination with one another can greatly enhance

the functionality of the callbox as well as the overall communication system. Available options include:

•Entry Keypad – RQX-127-XT-KP and RQX-427-XT-KP “keypad versions” of the XT-Series callbox are available to allow local access with up

to 500 unique codes. This version hosts a 2x6 DTMF keypad mechanically mounted to the stainless steel faceplate.

•RPS-EXPO – 12VDC power supply used to externally power the XT-Series callbox.

•RSS-100 - The RSS-100 is a complete solar power supply system consisting of a 10-watt solar panel, charge controller and 8 AH

rechargeable battery all housed in a rugged, ready-to-mount enclosure.

•R-STROBE - The R-STROBE is a powerful strobe light, giving a visual indication of a callbox in use. The R-STROBE is available in both AC

(R-STROBE) and DC versions (R-STROBE-DC).

•RCIM-1200 - The RCIM-1200 MDC-1200 encoder board allows each callbox to be assigned a unique unit ID number.

•RQX-XTMK – The RQX-XTMK is a mounting plate used to mount the XT callbox to most flat surfaces.

•RQX-XTMK-GN – The RQX-XTMK-GN is a mounting bracket used to mount the XT callbox to an industry standard gooseneck post.

For additional information and pictures of these items go to https://www.ritron.com/xt-series-heavy-duty-model-7-callbox-analog

and download pdf of the product brochure.

RQX-XTMK-GN

RSS-100

R-STROBE

RPS-EXPO

XT-Series Callbox

with Keypad

RQX XT-Series Wireless Callbox Basic Operation

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 2

BOUT THE

XT-S

ERIES

ALLBOX

...........................................................

The XT-Series Callbox is a 2-way radio transceiver used to communicate directly with portable, mobile and stationary radios; or

through radio repeaters with Ritron PC Programming software. Each callbox is equipped with the following features or capabilities.

•

Field Programming. Field programming allows you to quickly program your radio in the field without the need for a PC

programmer. Each radio can be field programmed to one of 27 VHF, 114 UHF, or 7 MURS channel table frequencies, and one

of 50 QC or 104 DQC interference eliminator codes.

•

MURS “License Free” Frequencies. MURS models can be programmed from a list of 7 MURS frequencies that do not

require FCC licensing.

•

154 Interference Eliminator Codes. Quiet Call (QC) and Digital Quiet Call (DQC) codes can be programmed to eliminate

other radio users not in your workgroup. For compatibility, new radios should be programmed with the same codes.

•

Volume Level. Field programmable or PC programmable to 5 – 100% volume level.

•

Normal or High Microphone Gain. Field and PC programmable to normal or high microphone gain.

•

Battery Powered. The XT-Series Callbox can be powered by 6 Alkaline D-cell batteries for 2 Watts transmit power at VHF, or

1.5 Watts at UHF. D-cell batteries can operate the radio for up to 7,000 transmissions. Go to https://www.ritron.com/tools and

download the RQX CALLBOX BATTERY LIFE CALCULATOR to compute the expected battery life of your callbox application.

When the callbox is used in a battery only application, the Auto Turn-Off feature should be enabled – this is the Factory Default

setting.

•

Low Battery Alert. The callbox will transmit an Alert Tone or pre-recorded Low Battery voice message at the end of each

transmission when the batteries approach end-of-life. This allows sufficient time for you to replace the batteries and assure

uninterrupted service.

•

External Power +12 VDC Capable. The XT-Series Callbox can be powered by an external +12 VDC source. This method of

powering the callbox allows the radio to remain ON at all times, like an intercom. Automatic Turn Off must be DISABLED via

Field or PC programming for Intercom operation.

•

+12 VDC Power Fail Alert. This feature can be enabled via Field or PC programming. The callbox will transmit an Alert Tone

or pre-recorded Power Fail voice message if it detects loss of +12 VDC power. The radio automatically continues to transmit an

Alert Tone once every hour (unless programmed for Automatic Turn Off) until +12 VDC is restored or the batteries are

depleted.

•

High/Low Power Output. When powered by External +12VDC the XT-Series callboxes can be Field programmed for High or

Low transmitter power output.

•

“Automatic Turn-Off” or “Intercom” Operation. The XT-Series Callbox can operate in the standard “Automatic Turn-Off”

mode (Factory Default), where the radio is normally OFF until the Call Button is pressed, or can be Field or PC programmed for

“Intercom” operation where the radio is always ON. See “External Power +12 VDC Capable” feature above.

•

DTMF or Selcall ANI. Field or PC Programmable for 3-7 digit DTMF or Selcall ANI codes which are transmitted at the

beginning of each message for radio identification.

•

Companded Audio. The radio can be Field or PC programmed to ENABLE or DISABLE audio companding. Companding will

compress transmit audio before sending it, and expand receive audio before it is heard on the speaker to reduce the

background noise common in analog radio communications.

•

Listen In. Allows remote activation of the transmitter when a unique 2-Tone, DTMF or Selcall code is received. Field or PC

programmable to 2-Tone, DTMF or Selcall codes and 4 different Listen In transmit times.

•

2-Tone, Selcall or DTMF Decoding. The Callbox can be programmed to decode unique 2-Tone, Selcall or DTMF codes for

selective signaling of the Callbox, “Listen In” remote activation of the transmitter.

•

Voice Messages. You can record custom voice messages that are played back during normal Callbox operation. Messages

include Greeting, Voice Alert, Sensor status, Battery status, and +12VDC Power Fail.

•

Sensor Turn-On. When operating the Callbox with Automatic Turn-Off enabled, the unit can be configured to turn itself ON

any time the Sensor Input is pulled LOW (ground). This allows an external switch closure to activate the Callbox.

•

2-Tone, Selcall or DTMF Decoding for Switch Operation.The Callbox can be programmed to decode unique 2-Tone,

Selcall or DTMF codes for switch output activation in GateGuard®applications.

•

Relay Switch Output. The switch output is a simple 3-Amp relay contact closure that can be used to OPEN and CLOSE a

gate, switch on a light, sound an alarm or any other application where remote control of an ON/OFF switch is required. The XT-

Series Callbox can be programmed to OPEN and CLOSE the switch output with a 2-Tone, Selcall, or DTMF code.

•

Sensor Input. The Callbox will send a warning tone or a pre-recorded voice message when a change in the Sensor Input is

detected. The Sensor Input will respond to an OPEN or CLOSED switch.

RQX XT-Series Wireless Callbox Basic Operation

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 3

XPOSURE TO

ADIO

REQUENCY

NERGY

.............................................

RQX-127-XT, RQX-127-XT-KP, RQX-127M-XT, RQX-127M-XT-CC, RQX-127M-XT-GG, RQX-127M-XT-GG-KP, RQX-127M-XT-KP

RQX-427-XT, RQX-427-XT-CC, RQX-427-XT-GG, RQX-427-XT-GG-KP, RQX-427-XT-KP

These products generate radio frequency (RF) energy when the PTT button on the front of the unit is depressed. These products

have been evaluated for compliance with the maximum permissible exposure limits for RF energy at the maximum power rating of

the unit when using antennas available from RITRON.

For antennas available from RITRON at the 20 cm (7.9 inches) minimum expected separation distance and greater, the maximum

RF exposure is well below the General Population / Uncontrolled limits. Antennas other than those available from RITRON have

not been tested for compliance and may or may not meet the exposure limits at the distances given. Higher gain antennas are

capable of generating higher fields in the strongest part of their field and would, therefore, require a greater separation from the

antenna. This product is not to be used by the general public in an uncontrolled environment unless compliance with the

Uncontrolled/General Population limits for RF exposure can be assured.

To limit exposure to RF energy to levels below the limit, please observe the following:

• Use only the antenna(s) available from RITRON for these models. DO NOT operate the radio without an antenna.

• DO NOT activate the transmitter when not actually wishing to transmit. These radios transmit recorded messages of a pre-

determined length to prevent continuous transmit times.

• When transmitting, make certain that the distance limits for the particular model in use are observed.

• DO NOT allow children to operate the radio.

When used as directed, this series of radios is designed to comply with the FCC’s RF exposure limits for “Uncontrolled/General

Population”. In addition, they are designed to comply with the following Standards and Guidelines:

• United States Federal Communications Commission, Code of Federal Regulations; 47 CFR §§ 2 sub-part J.

• American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992.

• Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition.

PERATING THE

XT-S

ERIES

ALLBOX WITH

ACTORY

EFAULT

ETTINGS

......

The XT-Series Callbox Factory Default setting is with Automatic Turn-Off ENABLED. This means the callbox is OFF and will not

receive a call until the callbox first initiates a call. When the callbox is used in a battery only application, the Auto Turn-Off feature

should be Enabled.

In Automatic Turn Off mode the callbox automatically shuts off after ten (10) seconds of no activity (i.e. transmitting or

receiving) on the channel.

To Initiate a Call

Press and hold the ON/PTT Button. The callbox will send a unique CALL TONE to alert radio equipped personnel. This CALL

TONE will also be heard at the callbox. Listen for the “beep”, then, begin speaking into the MIC. For best communication, the caller

should be 3 feet or less from the microphone.

To Receive a Call

1. When you have finished speaking, release the ON/PTT Button.

2. Any reply will be heard through the callbox speaker. If a call is not received within 10 seconds of releasing the ON/PTT Button

and there is no activity on the channel, the callbox will sound a low double tone and turn-off automatically. This automatic turn-

off feature is designed to conserve battery life.

Operation Notes

The XT-Series Callbox must be powered with Alkaline batteries ONLY, or alternatively, with an external 12 VDC power supply,

order Ritron model RPS-EXPO 110 VAC to 12 VDC cube power supply. When using an external 12 VDC supply, the Alkaline

batteries can be used as back-up. See page 5.

If there has been no activity for 10 seconds, i.e. either the ON/PTT Button has not been pressed or a call has not been received, the

unit automatically shuts OFF.

Low Battery Alert

The callbox will transmit an Alert Tone at the end of each transmission when the batteries approach end-of-life. This allows sufficient

time for you to replace the batteries and assure uninterrupted service. On XT-Series Callboxes the LOW battery alert tone can be

replaced by a LOW battery voice message.

RQX XT-Series Wireless Callbox Installation Instructions

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 4

PPLYING

OWER TO THE

XT-S

ERIES

ALLBOX

.......................................

The XT-Series Callbox may be powered by:

1. 6 D-cell batteries for 2W operation at VHF, 1.5W at UHF.

•Powering the callbox from internal alkaline batteries will allow for an installation that

does not require wiring to an external source of power.

•When the callbox is used in a battery only application, the Auto Turn-Off feature

should be Enabled – this is the Factory Default setting, battery only operation is not

suitable for Always-On mode.

2. An external +12 VDC source (Use Ritron pn RPS-EXPO) for 2W operation at VHF,

1.5W at UHF.

•Powering the callbox by an external source will allow the unit to remain in Always-

ON mode, like an intercom*. Be advised that battery only operation is not suitable

for Always-On mode.

To extend battery life, one of two battery saver options may also be used. See “POWER

MANAGEMENT OPTIONS” on page 6.

* Automatic Turn Off must be DISABLED via Field or PC Programming.

Using Internal Batteries

Batteries may be installed in the internal battery holder for a no trenching, no wires

required installation. If internal batteries are used, a LOW battery alert tone will be

transmitted when the battery voltage drops below a programmed value. The LOW battery

tone notifies personnel that the batteries should be replaced. On XT-Series Callboxes the

LOW battery alert tone can be replaced by a LOW battery voice message.

IMPORTANT! When installing D-cell batteries be sure all are the same, and are all new

cells. DO NOT mix new and used batteries.

XT-Series Battery Installation

1. Using the T-25 Torx bit included with the radio, remove the four corner

screws securing the metal faceplate to the green XT case. Lift the

faceplate from the XT case and place below the XT as shown to

prevent strain on the cable between the faceplate and the radio.

2. Using the T-25 Torx bit included with the radio, loosen the four corner

screws on the plastic interior case and separate the case halves.

3. Place the case front containing the radio PCB assembly off to the right

side as shown to prevent strain on the internal cables. The case front

assembly will fit between the internal black plastic case back and the

green XT case.

4. Disconnect the power cable connecting the battery holder to the radio.

5. Install 6 new D-cell batteries into the battery holder. Be sure to observe

polarity as indicated. Warning! Do not mix old and new batteries.

6. Re-connect the power cable.

7. Secure the plastic case halves with the corner screws. Be sure the

power cable is in the area below the battery holder and is not pinched

between the case halves.

8. Place the metal faceplate onto the green XT case and secure with the

four T-25 Torx screws. Be sure the cable between the metal faceplate

and the internal black plastic case is routed to the right side of the

plastic case and not over the top of it.

XT-Series battery cable disconnected

during battery installation

XT-Series case with metal

faceplate removed

RQX XT-Series Wireless Callbox Installation Instructions

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 5

Using External +12 VDC Power with Battery Back-up

Note: An additional hole, strain relief, or conduit will need to be installed into the callbox. See

“Connecting to the Callbox 6-Conductor Accessory Cable” section for details.

The unit may be powered by an external source of +12 VDC. This source should be filtered,

with minimum noise and hum, and capable of supplying at least 1 Ampere.

Factory Default programming of the callbox is optimized for battery power operation. The

External +12 VDC Power Fail Alert option is NOT ENABLED.

It is recommended that if an external source of power is used, that the internal batteries be

installed as a back-up against loss of power. If this option is chosen, we recommend that the

“External +12 VDC Power Fail Alert” feature be ENABLED via Field or PC programming.

How the Callbox will Operate:

If External +12 VDC Power Fail Alert Feature is NOT ENABLED:

•LOW battery detection can only occur when the +12 VDC is removed or failed.

•Radio will only check for LOW battery or DEAD battery condition when the radio is ON.

•If LOW battery is detected, a single Alert Tone will be transmitted at the end of the transmission.

•Radio does NOT automatically transmit a LOW battery tone. The callbox must be ON and Alert Tone is only sent at the end of a

transmission.

•If DEAD battery is detected, the radio ceases all operation. A DEAD battery tone is heard on the callbox speaker and the radio

will turn OFF.

•On XT-Series Callboxes the LOW battery alert tone can be replaced by a LOW battery voice message.

If External +12 VDC Power Fail Alert Feature is ENABLED:

•Radio always checks for External +12 VDC when the radio is ON. If loss of External +12 VDC is detected while the radio is in

standby: a single Alert Tone will be transmitted immediately.

•If loss of External +12 VDC is detected while the radio is in receive: a single Alert Tone will be transmitted after the received

message is complete.

•If loss of External +12 VDC is detected while the radio is in transmit: a single Alert Tone will be transmitted at the end of the

transmission.

•Once loss of External +12 VDC is detected and the Alert Tone is transmitted, the radio will automatically send the Alert Tone once

every hour until External +12 VDC is restored or the batteries are exhausted. If radio is set for Automatic Turn-Off (default setting)

this hourly alert will NOT occur.

•If Dead battery is detected the radio ceases all operation, a DEAD battery tone is heard on the callbox speaker and the radio will

turn OFF.

•On XT-Series Callboxes the loss of External +12 VDC alert tone can be replaced by a Power Fail voice message.

Using External +12 VDC Power without Battery Back-up

The Ritron RQX callbox can be programmed for always-on operation by disabling the Automatic Turn-Off option. This is

accomplished using the RQX PC Programmer, or through Field Programming. Once Automatic Turn-Off is disabled, the user

simply turns on the RQX by pressing the front panel PTT button and it will remain on as long as power is applied. If power to the

callbox is lost, the user must press the front panel PTT to restart the radio. For externally powered callboxes, battery backup is one

method of keeping the radio on if the primary external power is lost.

For users that do not want to rely on battery backup, and do not want to “restart” the callbox after a power loss, the follow-

ing modifications can be made to automatically restart/Turn ON the radio after a power loss.

For details or questions about this modification contact Ritron at 1-800-872-1872 and reference Ritron publication 14670034C, RQX

Q-Series Modification for Auto-Restart/Turn ON When Power Is Restored.

Important considerations before applying this modification:

•The Automatic Turn-Off option must be disabled.

•When Automatic Turn-Off is disabled the unit will consume the largest amount of current, but is always ready to instantly receive

messages. This mode should only be considered if an external source of +12 VDC is available.

•The callbox receiver will always be on. All radio communication on the programmed frequency and tone will be heard over the

RQX callbox.

For External +12VDC power,

order Ritron model RPS-EXPO.

RQX XT-Series Wireless Callbox Installation Instructions

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 6

OWER

ANAGEMENT

PTIONS

..........................................................

There are four power management options available to the XT-Series Callbox:

Automatic Turn-Off (In battery only application Auto Turn-Off must be Enabled).........................(Field or PC Programmable)

If Enabled (factory default), the callbox will automatically turn itself off after a programmed period of no activity (no transmissions

made and no calls received) has elapsed. Once the unit has turned itself off, it can only be turned back on by depressing the

ON/PTT Button. The programmed period of no activity necessary before the unit turns itself off is called the RQX Reset Time. RQX

Reset Time and Automatic Turn-Off can both be Field programmed, or PC programmed by the factory or your Ritron dealer via the

Ritron RQX Series PC Programmer. Automatic Turn-Off mode is the factory default mode for power management with an RQX

Reset Time of 10 seconds. Battery only operation not suitable for Always-On mode.

Battery Saver .............................................................................................................................................(PC Programmable Only)

This mode is similar to the Automatic Turn-Off mode except that the unit does NOT turn itself off after the RQX Reset Time has

elapsed. Instead it reverts to a mode where the unit goes to sleep and periodically wakes up to test for receive activity on the

channel. The Sleep Period (called Battery Saver Sleep Time) can be set using the Ritron RQX Series PC Programmer to between

0.5 and 8 seconds. Longer sleep times result in better battery life, but increase the chances that activity on the channel may be

missed. The unit will come out of this mode when activity is detected during the wake-up period or if the ON/PTT button is pressed.

The Automatic Turn-Off and Battery Saver modes cannot be used together. Battery only operation not suitable for Always-On mode.

Neither “Automatic Turn-Off” nor “Battery Saver” Used..................................................................(Field or PC Programmable)

If neither Automatic Turn-Off nor Battery Saver are used the unit will consume the largest amount of current, but is always ready to

instantly receive messages. This mode should only be considered if an external source of +12 VDC is available (see “Using

External +12 VDC Power with Battery Back-up” on page 5).

Sensor Turn-On...................................................................................................................................................................................

When operating an XT-Series Callbox

with Automatic Turn-Off enabled, the

unit can be configured to turn itself ON

any time the Sensor Input is pulled

LOW (ground). This allows an external

switch closure to activate the Callbox.

When the switch closure is detected

the Callbox will turn on and

automatically transmit the Sensor On

alert or Sensor ON voice message.

The Callbox is then in normal operating

mode and will automatically turn itself

off after a programmed period of no

activity as described in the Automatic

Turn-Off topic in this section.

For Sensor Turn-On operation the

Sensor Turn-On jumper must be placed

into the “Turn-On” position. Refer to

FIG-1 for correct placement of the

jumper. If the Sensor Input is not used

the jumper placement has no effect on

Callbox operation.

ELAY

OLARITY

UMPER

ETTING

.........................................................

The XT-Series Relay Switch Output is a simple 3-Amp relay contact closure that can be used to OPEN and CLOSE a gate, switch

on a light, sound an alarm or any other application where remote control of an ON/OFF switch is required. The XT-Series Callbox

can be programmed to OPEN and CLOSE the switch output when a specific condition is met. Refer to the “Relay Switch Output

Options (Allows Control of an External Device)” section of this manual for details.

The Relay Switch Output can be set for “normally-open” or “normally-closed” operation by setting the position of the Relay Jumper

as shown in FIG-1. If the Relay Switch Output is not used the jumper placement has no effect on Callbox operation.

FIG-1: Sensor Turn-On Jumper Shown in Turn-On Position

Sensor Turn-On

Jumper in Turn-On

position

Relay Jumper

in Normally-

Open position

RQX XT-Series Wireless Callbox Installation Instructions

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 7

NTENNA

UMPER

ETTING

..................................................................

The XT-Series Callbox is equipped with an Antenna Selector Jumper that will route all incoming and outgoing radio signals

to either a built-in internal antenna, or to the SMB RF Test / External Antenna connector. XT-Series Callboxes do not have an

internal antenna, therefore the Antenna Selector Jumper must always be placed in the RF Test / External Antenna position!

The XT-Series Callbox comes from the factory with the Antenna Selector Jumper in the “SMB RF Test / External Antenna” position

for operation with the AFB-1545 antenna installed in the green XT callbox case.

Important - For testing through the SMB RF connector, the AFB-1545 antenna must be disconnected and the Antenna Selector

Jumper must remain in the “SMB RF Test / External Antenna” position. Extreme care must be taken when disconnecting the AFB-

1545 from the SMB connector. Do not attempt to pull it loose with the cable, it is best to carefully pry it off.

SMB Connector with

AFB-1545 Antenna

connected

Antenna Selector

Jumper Setting

The position of the

Selection Jumper shown

is for connection to the

AFB-1545 Antenna

SMB Connector with

AFB-1545 Antenna

disconnected for testing

through SMB RF Test

connector

Antenna Selector

Jumper Setting

The position of the

Selection Jumper shown

is for connection to the

SMB RF Test connector

RQX XT-Series Wireless Callbox Installation Instructions

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 8

ALLBOX

ONTROLS AND

ONNECTORS

..............................................

Case Screws

A T-25 Torx screw is located in each corner of the case front.

These 4 screws are used to secure the case front containing

the radio, to the case back that contains the batteries.

Speaker Connector

The internal speaker is connected to the radio printed circuit

board with a polarized connector.

Record Audio Input

Allows .wav audio files from your computer to be used when

recording Voice Messages.

Program Display

A single digit LED display is used during field programming of

the radio.

Program Button

A small, momentary pushbutton is used for field programming

the XT-Series Callbox.

On/PTT Connector

The On/PTT switch is connected to the radio printed circuit

board with a polarized connector.

Accessory Connector

The 6-pin, polarized connector is used to connect external

input/output devices. This allows connection of an external +12

VDC input, an external DC level sensor input, and a 3A contact

switch closure output.

Relay Polarity Jumper

The Relay Polarity jumper can set the relay output to normally

open or normally closed. (See FIG-1)

Sensor Turn-On Jumper

The Sensor Turn-On jumper can be set to turn-on the radio

whenever the Sensor Input is pulled low. (See FIG-1)

BNC Antenna Connector

BNC style connector for the AFB-1545 antenna included with

the XT-Series Callbox.

USB Programming Connector

A Mini-USB style connector is used to connect the cable from

the PC programmer to the radio.

SMB RF Connector

SMB style RF connector for RF testing and connection to the

AFB-1545 antenna.

Antenna Jumper

The antenna jumper must be in the “SMB RF Test / External

Antenna” position when using the XT-Series Callbox.

Microphone

The microphone is installed on the PCB back side.

D-Cell Battery Holder

The battery holder inside the case back is used for the

installation of six D-cell alkaline batteries. Refer to the labels

beneath the cells for correct installation of the batteries.

Battery Mating Connectors

Polarized, 2-pin mating connectors are used to connect the

batteries to the radio circuit board.

BNC Antenna Connector

USB Programming

SMB RF Connectors

Antenna Jumper

(Jumper set for XT)

Microphone

(PCB back side)

D-Cell Battery Holder

with Batteries Installed

Battery Mating

Connectors

FIG-2: XT Callbox Controls and Connectors

Case Screws

(4 Corners)

Speaker Connector

Record Audio Input

Program Display

Program Button

On/PTT Connector

Accessory Connector

Relay Polarity Jumper

Relay

Sensor Turn-On

Jumper

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transceptor de Ritron

Ritron

Ritron DTX-Ls Series Manual de usuario

Ritron

Ritron DTXM-465-0BN6I-M Manual de usuario

Ritron

Ritron RPM-050 Manual de usuario

Ritron

Ritron Q Series Manual de usuario

Ritron

Ritron DTXM-NXDN Series Manual de operación y mantenimiento

Ritron

Ritron DTX- 60 Series Manual de usuario

Ritron

Ritron RadioNexus Manual de usuario

Ritron

Ritron SPX-200 Manual de usuario

Ritron

Ritron RT-453 Manual de operación y mantenimiento

Ritron

Ritron RTT Manual de operación y mantenimiento

Ritron

Ritron DTX Plus Series Manual de usuario

Ritron

Ritron RPM-150 Manual de usuario

Ritron

Ritron SST-444 Guía de inicio rápido

Ritron

Ritron RPM-150 Instrucciones de instalación y funcionamiento

Ritron

Ritron DTXM-460-0BN6I-M-FIPS Manual de usuario

Ritron

Ritron DTX-165-0 Manual de operación y mantenimiento

Ritron

Ritron SPX-200 Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario