Ripmax BOOMERANG TORUS Manual de usuario
Read through this manual carefully
before you begin building and follow
it during construction.
ARTF KIT.
Specification:
Wingspan: 2,286mm (90")
Length: 2,209mm (87")
Weight: 13.6 -15.4Kg (30 - 34 lbs)
(Approx.)
Radio: 7+ Channel (Required)
Turbine: 110 -160N (24 - 36 lbs)
(Required)
Servos: 10 x (20+ kg/cm)
(Required)
Safety Precautions
THE TORUS TURBINE MODEL IS DESIGNED FOR EXPERIENCED MODELLERS. THIS MODEL
IS NOT RECOMMENDED FOR BEGINNERS. TURBINE MODELS ARE FOR ADVANCED FLYERS
AND SHOULD NOT BE ATTEMPTED BY THOSE WITH INSUFFICENT BUILDING & FLYING
EXPERIENCE.THIS INSTRUCTION MANUAL IS FOR GUIDANCE ONLY. IF YOU ARE UNSURE
OF ANY MODEL BUILDING TECHNIQUES, SEEK HELP FROM AN EXPERIENCED MODELLER
OR CONTACT RIPMAX LTD, FOR ASSISTANCE. JET MODELS ARE DANGEROUS IF
CONSTRUCTION IS CARELESSLY OR INCORRECTLY CARRIED OUT. AS THE BUILDING
AND FLYING OF THIS KIT IS OUT OF OUR CONTROL AFTER POINT OF SALE, NO LIABILITY IS
ACCEPTED BY RIPMAX LTD. FOR ANY ACCIDENT OR LOSS, HOWEVER CAUSED. PURCHASE
OF THIS KIT IMPLIES ACCEPTANCE OF THESE CONDITIONS BY THE PURCHASER.
TO DECLINE THESE TERMS, RETURN UNUSED KIT TO YOUR SUPPLIER FOR A FULL REFUND.
NOTES ON HORN POSITIONS
Mount the horns so the clevis holes are 1/4" (6mm) behind the hinge line for the
ailerons to give differential and on the hinge line for rudders and elevators.
But on the FLAP horns, move the horn bolt rearwards about 1"(25mm.) from
hinge line and drill the hole for the horn bolt back so that the hole in the flap
is a full 3/4" back behind the hinge line. This will allow the flap to drop almost
to 90 degrees full deflection.
Insert all hinges and check range of
movement, then apply thin CA glue.
As With all ARF Kits, it is essential to make
a thorough check of all glue joints and add
epoxy or CA glue if required.
2
Be sure to apply thin C.A. glue to both
sides of each hinge. Then pin each
hinge from below using cocktail sticks,
fore and aft of the hinge line. Do not
pierce the top surface.
Also, pass a hot iron over all the film
covering edges, especially leading
edges of the covering to ensure
adhesion, and then seal these with a
clear dope or clear coat using a very
small brush.
10
Cocktail stick pin
Cocktail stick pin
Follow Sullivan horn instructions.
2.6 x 12mm TP Screw
8
Use 1” 4-40 stud for pushrods
Supplied
Supplied
Supplied
Not Supplied
2.5mm Hex Wrench
8
4 x 10mm Bolt
4 x 10mm Bolt
4 x 10mm Bolt
Tip Tank Installation
Regular wing tips.
4
4 x 10mm Bolt
6mm 4
4
4
Fix the alloy rods in the wing with the bolts supplied.
Use glossy plastic packing tape or similar over the wing
to ensure release, then use 5 minute epoxy glue in the
wing tips. Line up and press the tip home while the glue
sets. Then slack off the bolts and release the tip with the
tabs in place.
3 x16mm TP Screw
3 x16mm TP Screw
Not Supplied
Not Supplied
8
Not Supplied
Up to 2.75 inches
Not Supplied
9
Be sure to glue the rudder hinges securely.
This is vital for safe flying!
1 metre extension
1.25 metre extension
2.6 x 12mm TP Screw
8
2.6 x 12mm TP Screw
Cut away covering film
Cut away covering film
Supplied.
Supplied.
Use short lengths of 4-40 stud
and Sullivan clevises and
horns supplied.
2.6 x 12mm TP Screw
2.6 x 12mm TP Screw
8
13
Assemble left and right sides
the same way.
Assemble left and right sides
the same way.
Supplied
Supplied
4-40 stud pushrod
Rudders
2
4
4 x 10mm Bolt
2
2
Assemble left and right sides
the same way .
14
8mm Alloy Rods
6mm Alloy Rods
Carbon fibre spars
6mm Alloy Rods
8mm Alloy Rods
Carbon fibre spars
4 x 10mm Bolt
15
16
2
2
2
4 x 16mm Screw
4mm Lock Nut
4mm Washer
Additional safety fitting to stabilisor
With tailplane (Stab.) firmly
screwed down, pass a 3.6mm
drill through the holes in the fins
and drill a hole through the metal
tongue projecting down from the
Stab. Remove the Stab and tap
the new hole in the tongue out to
4mm thread. Repeat the
process through the other fin.
During assembly apply the 4mm
X16mm bolt through the fins and
the tongues and lock in place
with the 4mm nylock nuts and
washers supplied. If a 4mm tap
is not available drill the hole in
the tongue out to 4mm and
assemble the same way.
4 x 20mm Bolt
4 x 20mm Bolt
4 x 20mm Bolt
4
Tabla de contenidos
Otros manuales de Juguete de Ripmax
Ripmax
Ripmax Mini Xcalibur E Jet Manual de usuario
Ripmax
Ripmax EF - 2000 TYPHOON Manual del propietario
Ripmax
Ripmax Transition Vtol Manual de usuario
Ripmax
Ripmax WOT 4 FOAM-E Manual de usuario
Ripmax
Ripmax J!VE Fun Fly Manual de usuario
Ripmax
Ripmax mini Bossanova Manual de usuario
Ripmax
Ripmax Trainer 40 Manual de usuario
Ripmax
Ripmax WotsWot XL Manual de usuario
Ripmax
Ripmax Phase 5 E Manual de usuario
Ripmax
Ripmax Hellcat Slim Manual de usuario
Ripmax
Ripmax BOLERO A-ARTF6720CS Manual de usuario
Ripmax
Ripmax Mini Wot4 Manual de usuario
Ripmax
Ripmax Bolero Manual de usuario
Ripmax
Ripmax WOT 4 MK2 Manual de usuario
Ripmax
Ripmax Sky Spy A-ARTF68713 Manual de usuario
Ripmax
Ripmax NANO Boomerang Manual de usuario
Ripmax
Ripmax Sky Spy A-ARTF68752 Manual de usuario
Ripmax
Ripmax Trainer 40 Manual de usuario
Ripmax
Ripmax Easy Street 2 Manual de usuario
Ripmax
Ripmax WOT4-E Manual de usuario
