Rinnai RHFE-556FA Guía de inicio rápido

~'l

...

·.

''il1

HOME OWNER IINSTALLER

FOR YOUR SAFETY

THIS MANUAL MUST BE READ IN ITS

ENTIRETY BEFORE OPERATING HEATER

RHFE-556FAlFTRA

ENERGYSAVER

GAS DIRECT VENT WALL FURNACE

Owner's Operation and Installation Manual

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, AFIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS

LIFE.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS

AND LIQUIDS

THE VICINITY

THIS OR ANY OTHER APPLIANCE.

WHAT TO DO IF YOU SMELL GAS

•DO NOTTRY

LIGHT ANY APPLIANCE.

•DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY PHONE

IN YOUR BUILDING.

•IMMEDIATELY CALL YOUR GAS SUPPLIER FROM ANEIGHBOR'S

PHONE. 'FOLLOW THE GAS SUPPI:IER'S INSTRUCTIONS.

•.IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE

DEPARTMENT.

INSTALLATION AND SERVICE MUST BE PERFORMED BY AQUALIFIED

INSTALLER, SERVICE AGENCY OR THE GAS SUPPLIER.

INSTALLER: MUST LEAVE MANUAL WITH UNIT AFTER INSTALLATION.

OWNER: RETAIN THIS MANUAL SAFELY, FOR FUTURE REFERENCE.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION,

SERVICE

MAINTENANCE

CAN CAUSE PROPERTY

DAMAGE,

PERSONAL

INJURY

LOSS

LIFE.

REFER

THE

OWNER'S

INFORMATION

MANUAL

PROVIDED WITH THIS APPLIANCE. INSTALLATION AND

SERVICE

MUST

PERFORMED

QUALIFIED

INSTALLER, SERVICE AGENCY OR THE GAS SUPPLIER.

Rinnai Gas FF Heater

(Forced Flue)

ENERGYSAVER RHFE-556FAlFTRA

Table

Contents Page

FEATURES OF THE RHFE-556 UNITS/SAFETY DEVICES 1

TECHNICAL DATA/GAS PRESSURE

SETIING

IMPORTANT POINTS/USAGE AND INSTALLATION MUST 3

DIMENSIONS 5

SPECIFICATIONS 6

SAFETY POINTS 8

GETIING

TO KNOW YOUR NEW RHFE-556FA/FTRA 10

CONTROL PANEL LAYOUT ,

REMOTE CONTROL 12

CUT-AWAY DIAGRAM 13

NOTICE BEFORE INSTALLATION 14

INSTALLATION INSTRUCTIONS

GAS CONNECTION 16

VENT LOCATION 17

FITIING

TOP SPACE+WALL CLIP 17

USA/CANADIAN VENT REGULATIONS 18

LOCATION/CLEARANCES 19

SLEEVE AND MANIFOLD INSTALLATION

OPERATING INSTRUCTION LABEL 25

ADDITIONAL CUSTOMER OPERATING INFORMATION 26

PROGRAMMING ON/OFF TIMERS/CLOCK(556FTRA ONLY) 32

OVERRIDE FUNCTION/USING THE REMOTE CONTROL(556FTRA ONLY) 36

TESTING/CHECK 37

PRE-SERVICE CHECK 38

TROUBLE SHOOTING 39

ERROR MESSAGES 40

MAINTENANCE/SERViCE

WIRING DIAGRAM 42

WARRANTY INFORMATION .43

SCHEMATIC DIAGRAM/PARTS LIST .45

RHFE-556 FLOW DIAGRAM :

5.5

,EXTENDED FLUE PIPE KIT 57

CONVERSiON 62

rJFEATURES OF THE RHFE-556FAlFTRA UNITSI

(

.:..-_----------------------------.

•Clean Heating Forced Flue Type

•Easy Operation One-Touch

Ignition

•Sensible Temperature

Control

Feature

•Comfortable Room Temperature

Control

and

Display

•Warm

Air

Outlet

Floor

Level (Keeps Your Feet Warm)

•

Child

Safety

Lock

•Room Temperature Setting Memory

•

Dirty

Air

Filter

Indicator

Lamp

•Energy-Saving

Economy

Setting

•

Humidifier

Tray

•

Air

Flow Directional

Louvers

•Direct Vent Easily Installed

•

Proportional

Heating Variable Capacity

•Hush! Quiet Operation )

•Modern Design Minimizes

Floor

Space Requirements

(•Failure Message Display

•Dual Timers-556FTRA

only

"-~

/ •

Timer

Override Mode-556FTRA

only

(\,,_,

~_~e_~_~_~e_at_cM_o_~_~re_~_I~_~5_6

6_7-r_R_:_A_o_~_~_ly

__1

Spark

Safety Device: Automatically shuts unit down when there is an abnormal spark at time

of ignition.

Flame Failure Device: Activated when burner flame fails. This prevents raw gas from being

released.

Overheat Switch:

Two Fusible

Links:

This device automatically cuts the gas off if the heater exceeds a

predetermined temperature. This

normally caused by an

obstruction

front of the louvers, or ablocked fan filter.

Backs up the overheat switch. If the fusible link cuts the unit off, a

service call by an authorized person is required to replace the link.

Overcurrent

Prevention Device: This is a 3 amp. glass fuse found on p.e; board. Design

to shut unit down in case of overcurrent. If fuse

bloWs

all

indicator lamps will be "OFF".

Power Outage Safety Device: This safety device cuts off gas passage and stops

operation.

-1-

TECHNICAL

DATA

WEIGHT DIMENSIONS GAS RATE (BTU/h)

INPUT OUTPUT

Lbs. Width: 29 1/2"

Height:

13/16"

Depth: 913/16" LOW 8,200 8,200 LOW 6,640 6,640

HIGH 21,500 20,700 HIGH 17,420 16,770

Burner Orifices:

RHFE-556FA/FTRA-P use: Orifice part #AU129-21 0x02-0.85(0.033")

RHFE-556FA/FTRA-N use: Orifice part #AU129-21 0x02-1.13(0.044")

GAS CONVERSION SPECIFICATIONS

MODEL GAS

DIAMETER

PRIMARY SECONDARY MANIFOLD DIFFERENTIAL DIP SWITCH

TYPE ORIFICE(mm) DAMPER DAMPER PRESSURE (W.C.) POSITION

RHFE-556FA LPG

<1>0.85

556F-209-7 556F-208-5 4.5"W.C. 0.8"W.C.

ON'"

(<I>

2.5 x15) OFF

RHFE-556FA

<I>

1.13 556F-209-7 556F-208-7 3.8"W.C. 0.7"W.C.

J'.

(33 x47hole) OFF

RHFE-556FTRA LPG

<1>0.85

556F-209-7 556F-208-5 4.5"W.C. 0.8"W.C.

ON'"

OFF

RHFE-556FTRA NG

<I>

1.13 556F-209-7 556F-208-7 3.8"W.C. 0.7"W.C.

J'.

OFF

URE

SETTING PROCEDURE

Check and ensure SW6 Dip Switches are

correct for the gas type for which the appliance

to be used. (Refer to diagram below.)

SW6 DIP SWITCH

There are two test points, one

the manifold,

one

the gas control assembly. Connect

pressure gauge to both test points. Using

electronic manometer, connect the eside to

the manifold test point. (Refer to data plate for

pressure.)

GAS SUPPLY PRESSURE

1 2 J4

Press the ON/OFF button to operate the appliance.

With appliance operating, press SW5 once.

Press SW4 to operate appliance

forced low.

Adjust the setting to the correct pressure using the

"A " and

"buttons

the control panel.

Press SW4 again to lock

the selected setting.

Press SW3 to operate appliance

forced high.

Adjust the setting to the correct pressure using the

"A " and

"buttons

the control panel.

Press SW3 again to lock

the selected setting.

Press SW5 once

return heater to normal operation.

10.

Press

the

ON/OFF

button

turn the appliance

off.

11. Remove the gauge from the test points and replace

the test point screws.

12.

Test for gas escapes.

J'~~

·The minimum and maximum inlet gas supply pressures

·1··

are for the purpose of input adjustment.

r._·

'·.·.·

·Heaters may

converted from one gas to another

using Rinnai conversion kits. (See page

62)

·Output efficiency is 75% of rated input for Canadian

installations.9"W.C.

13"W.C.

PROPANE

I2J4

LPG

556FAI

FTRA

NATURAL

MAXIMUM 10.5"W.C.

MINIMUM 5"W.C.

-2-

IMPORTANT

POINTS

USAGE

AND

INSTALLATION

MUSTS-I

Unpack heater and check for damage. (DO NOT INSTALL DAMAGED HEATER.) If heater is

damaged, contact your supplier for advise. Before installing aheater, check the label for the correct gas

type (see label on side of heater). Refer to local gas authority for confirmation of gas type if you are in

doubt.

Included in Carton:

.Customers Operating Information

.Conversion kits

IMPORTANT

Before using

this

product, please read

this

manual carefully

insure proper use

product.

The appliance must be installed

accordance with state and local codes.

For information on gas type, see data plate on the appliance.

This heater must not be installed whese curtains or other combustible materials could come into

contact with it.

some cases curtains may need restraining.

This appliance is not designed to be built in.

If you move, check the gas type

the area where you are moving to. The local gas authority will be

able to advise on local regulations.

This heater discharges alarge volume of warm air at low level to provide even heat distribution. If

the air in the room contains cooking vapor or cigarette smoke, and the heater is used on acarpet,

the surface of the carpet may become discolored.

addition, some nylon carpets contain dyes

which may be affected by the warm air flow. Some soft vinyl surfaces are also subject to distortion,

or discoloration by warm air. To prevent discoloration

carpets, etc., amat should be placed under

the appliance, extending about 30" (750mm) in front

it.

Diagram shows minimum clearances from combustible materials.

40"

12"

{}

Read these rules and the instructions carefully. Check all local codes. Failure to follow these could

cause amalfunction of the heater resulting

death, serious bodily injury and/or property damage.

This heater is designed for use only with L.P. or natural gas. Make sure that the type of gas to be

supplied to this unit matches that shown on the rating plate on the heater. If aconversion of the unit

is needed. Conversions must be performed at Rinnai America or authorized agent

owner's

expense.

-3-

WARNING: Any change to this heater or its controls can

dangerous.

10. If agas leak is suspected, turf} heater off, turn gas supply valve off at appliance connector valve.

Open windows to ventilate area immediately and contact your dealer or gas company.

.00

not place clothing or flammable materials, gasoline and other flammable vapors and liquids, on or

near the heater.

12. Young children should be carefully supervised when they are

the same room with the heater.

13. LPG containers must not

installed indoors.

14. Do not use this room heater if any part has been under water. Immediately cal! aqualified service

technician to inspect the room heater and to replace any part of the control system and any gas

control which has been under water.

15. Adequate clearances for accessibility for purposes of servicing and proper operation should

provided.

16. Adequate clearances around air openings should be provided.

17. Do not install

areas where curtains, drapes, clothing, or other moving flammables are within 12

inches of this unit.

18. Periodic examination of the venting system is required.

19. The flow of combustion and ventilation air should not be obstructed.

20. "This appliance must

installed in accordance with the manufacturer's instructions and the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or astandard for

manufactured home ANSI A22512/NFPA

501

21. "This appliance must be installed

accordance with the current standard CSA Z240.4 GAS

EQUIPPED RECREATIONAL VEHICLES AND MOBILE HOUSING. Cet appareil doit ette installe

conformement aux, exigences de la norme Z240.4 en vigeuer de I'ACNOR, Installations de gaz dans

les constructions mobiles et vehicules recreatifs."

GENERAL INFORMATION

THIS SERIES

DESIGN CERTIFIEDBY THE AMERICAN GAS

ASSOCIATION LABORATORIES (AGA) AND INTERNATIONAL

APPROVAL SERVICES (lAS).

ALTERATION OF THE ORIGINAL DESIGN INSTALLED OTHER

THAN AS SHOWN

THESE INSTRUCTIONS OR USED WITH

ATYPE OF GAS NOT SHOWN

THE RATING PLATE, IS

THE

RESPONSIBILITY

OF THE PERSON AND COMPANY

MARKING THE CHANGE.

·Rinnai is continually updating and improving products. Therefore, specifications are subject to

change without notice.

·Thank

you=for

purchasing Rinnai force flue gas heater.

·Please read the warranty thoroughly and keep it

asafe place.

-4-

(;~~

•..

D-IM-E-N-S-IO-N-S-----........;.....·I

'---

(Ir

iJT€)

61/2"

(165mm)

33/8"

(85mm)

Power supply

Gas Inlet

95/8"

(245mm)

89/16"

(217mm)

"(280mm)

•

-I

37/16" (88mm)

III

!£.

....

OJ v

.... ....

....

r:::

Exhaust at rear of unit

(

291/2"

(750mm)

-5,..-

SP_

.•.

,E_C_F--.:-.,C_A_

~_IO_·.·

N_S---.:-

~(g

BTU/h MIN. CLEARANCES I

FAN

CFM I

MODEL #OUTPUT

INPUT OUTPUT SIDE TOP FRONT !

FE-556FAlFTRA Low Low LO:110.5

8,200 6,640

12" 40"

High (50mm) (300mm)

NATURAL High HI:162.7

21,500 17,420

RHFE-556FAlFTRA Low Low LO:110.5

8,200 6,640

12"

40"

High High (50mm) (300mm) (1m)

PROPANE 20,700 16,770 HI:162.7

SPECIFICATIONS

Type of Appliance Fan forced flued gas furnace J

Model RHFE-556FAlFTRA ENERGY SAVER

Width-

(750mm) 29 1/2"

'."

Dimensions

Depth-(250mm

with back spacer)9 13/16"(with back spacer)

Height-(554mm)

13/16"

Weight Approx.

Ibs.

Connections

Electrical-AC

120V 60Hz 52 watts

Gas-1/2/1female NPT

Combustion System Stainless steel bunsen burner

Ignition System Continuous spark

Operation Finger touch control buttons (non-lock)

Temperature Control Electronic thermostat HI-LOW/OFF

Up/down switch

.Modulates Continuous

Temperature Range

LOW=55°F

60°F-80°F

HI=High

Combustion

Warm Air Outlet Bottom front louver

Indicators/Lamps Burner ON, child lock, filter, economy, temperature display,

Timers(FTRA Only)

Operating Buttons On, Up/down, child-lock, economy/Timers, Override (FTRA Only)

Economy Mode Energy saving feature

Humidifier Tray

Capacity-3

pints (1300cc)

1.--

-6-

Flame failure -Flame rod

Over heat -Bi-metal switch, thermal fuse, thermistor

Power failure -PCB

Safety Devices Power surge - 3 Amp. fuse

Fan delay -Micro computer timer

Pre-purge -Combustion fan, pre-purge timer, spark sensor

Room over heat -Automatic cut off at 104°F after 10 minutes

Noise Level Range

HI-LOW=41-32dB(A}

Combustion Method Forced combustion

TYPE Air Supply Exhaust Closed Type .

Radiation Method Forced connection

Wall Penetration (80mm) 3

1/8"

AIR SUPPLY/ Hole

EXHAUST PIPE Max. Extended

(4m,

2bends}=13ft., 2bends

Length

SPECIFICATIONS FOR VENT SIZES

3"-41/2"

Thin Walls Mobile Home

(75-115)

A>4

1/2"~9

1/2" Wood Walls

(115-240

)

91/2"-153/4"

Wood/Brick

(240-400

)

C15 3/4

"-23

5/8" Brick/Block

(400-600

)

235/8"-31

1/2"

Special

(600-800

)

** BTU -Efficiency increase with vent size. Clearances from combustibles see pages 6and 28.

** Thermal efficiency rating determined under continuous operating conditions.

Efficiency results based

DOE regulations. Output efficiency is 75% of rated input for Canadian

installations.

-7-

SAFETY·POINTS i/l

'------------'---------1f~)

Do not restrict the warm air discharge by

placing articles

front of the heater.

Do not spray aerosols while the heater is

operating. Most aerosols contain butane

gas, and can be afire hazard if used near

this heater when it is

use.

Do not allow curtains or other flammable or

combustible materials to come into contact

with the heater.

Combustible materials must not

placed

where the heater could ignite them.

-8-

This appliance must not be used for any

purpose other than heating.

Do not install the heater

an un6sually

dusty area. x

Do not

allOW

anyone to sit on or lean against

the appliance.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Horno de pared de Rinnai

Rinnai

Rinnai RHFE-1004FA Manual de usuario

Rinnai

Rinnai RHFE-263FA 2 Guía de inicio rápido

Rinnai

Rinnai RHFE-431WTA Guía de inicio rápido

Rinnai

Rinnai RHFE-431FA Guía de inicio rápido

Rinnai

Rinnai EX22DT Manual de usuario

Manuales populares de Horno de pared de otras marcas

Empire Heating Systems

Empire Heating Systems FAN TYPE VENTED WALL FURNACE FAW-55IP Guía de inicio rápido

Braemar

Braemar WF2000 Manual de usuario

Empire

Empire FAW40IPXLP-1 Guía de inicio rápido

Empire

Empire DV-55IP Guía de inicio rápido

Empire Heating Systems

Empire Heating Systems GWT-25-2 SG Guía de inicio rápido

Empire Heating Systems

Empire Heating Systems DV-35-2SG Guía de inicio rápido

Empire Heating Systems

Empire Heating Systems GWT-25-2 SG Guía de inicio rápido

Empire Heating Systems

Empire Heating Systems DVC55SPPXLP-1 Guía de inicio rápido

Empire Heating Systems

Empire Heating Systems DVC55SPPXLP-2 Guía de inicio rápido

Napoleon

Napoleon GDS3700-N Manual de usuario

HouseWarmer

HouseWarmer HWDV080DVN-1 Manual de usuario

Empire Heating Systems

Empire Heating Systems PVS18(N Instrucciones de funcionamiento

Empire Heating Systems

Empire Heating Systems DV-25T-1 Guía de inicio rápido

Empire Heating Systems

Empire Heating Systems GWT-25 Manual de usuario

Empire Heating Systems

Empire Heating Systems MV 145 Guía de inicio rápido

Longvie

Longvie DV20 Manual de usuario

Empire

Empire DV-25-2SG Guía de inicio rápido

Braemar

Braemar WF2000 Manual de usuario