Rinnai Linear Series Manual de usuario
Linear collection gas fireplaces
Flue installation guide
Important
Rinnai Linear gas replace ueing shall be installed in accordance with:
-Manufacturer’s installation instructions
-Current AS/NZS 3000, AS/NZS 3500, AS/NZS 5601.1 and G12/AS1
Must be installed, commissioned and serviced by an authorised person,
being in New Zealand a licensed gastter.
The Linear must be installed with an approved ue system, approved
components are shown in this guide.
Warning
Improper installation, adjustment, alteration, service and maintenance
can cause property damage, personal injury or loss of life.
For more information about buying, using, and servicing of Rinnai
appliances call: 0800 RINNAI (0800 746 624).
Rinnai New Zealand Limited
105 Pavilion Drive, Mangere, Auckland
PO Box 53177, Auckland Airport, Auckland 2150
Phone: (09) 257 3800
Email: [email protected]
Web: rinnai.co.nz
youtube.com/rinnainz
facebook.com/rinnainz
General ueing guidelines ....................................4
Flueing options .....................................................6
Air hose connection ..............................................9
Flue components ..................................................10
Flue component connections................................11
Side direct ue assembly......................................12
Side extended ue assembly................................13
Up and back ue assembly ..................................14
Down and out ue assembly ................................15
Cutting the ASPDFK and ESPIPE900 to length ...16
Steps to create a wall terminal .............................17
Appendices
Appendix 1: ESBEND 90° ....................................19
Appendix 2: ESBEND 45° ....................................20
Contents
Every gas re requires a ue system that will draw eectively and clear ue products safely
under all wind and climatic conditions. It is up to the installer to ensure the appliance is provided
with an eective ue.
Installer responsibility
4 | Linear ue installation guide 13541-A 01-20
General ueing guidelines
Flue clearances to
combustibles
Due to the heat from the ue components, maintain a 25 mm
clearance to combustibles for the rst 500 mm of ue.
Flashings Flashings are not included with the ue kits, these must be
specied.
Flue support The weight of the ue system must not be supported by the
appliance, it must be self-supporting. Supporting the ue is
usually completed during the framing stage with ue supports
or straps within the cavity. Wall straps are included with most
Rinnai ue components.
Securing the ue To prevent the ue from moving or coming apart:
• Joints between the ue components MUST BE secured by
short screws1 (max. length 6 mm) through the outer pipes
(easier to undo if necessary).
• Flue components must be secured to the wall using the ue
straps provided in each ue kit, refer image above.
Lubricate o-ring seals
before connecting
The inner pipe joints are sealed with an o-ring seal lubricant. A
small plastic tub of silicone grease is provided with the main ue
kits. Use this silicone grease to lubricate the o-rings on the inner
pipes prior to assembly. This is important as o-rings can dry out
and break, and replacing o-rings is dicult.
Do not use petroleum based lubricants as these will cause
deterioration of the o-ring seals.
Flue sections located
outside
Sections of the ue located outside require the following:
• Only use PVC cement between the joints of the outer PVC
pipes to secure and seal the joints against ingress of dust
and water.
• Only use non-acidic silicone sealant between the joints of
the outer PVC pipe and any mating aluminium components
to seal the joints against ingress of dust and water. Silicone
containing acetic acid or other acids as the curing agent may
cause the aluminium to corrode.
Shared ues Gas appliances must not be connected to a chimney or ue
serving a separate ue burning appliance.
Condensate A condensate trap or drain is not required for Linear installations
as little or no condensate is produced, as the ue runs hotter in
Linear installations.
1 Screws must not touch the inner pipe—could cause a transfer of heat to the plastic outer and potentially
melt the plastic.
Linear ue installation guide 13541-A 01-20 | 5
2° fall to the horizontal ue
terminal
There must be a continuous fall of at least 2° to
the horizontal wall termination. This is so any
rain water exits the ue naturally.
fall
Flue terminal locations Flue terminals must be compliant with the ue terminal locations
shown in AS/NZS 5601.1.
• The ue terminal must be positioned away from any
ammable materials.
• Keep snow and other items, such as outdoor furniture well
clear of the ue terminal at all times.
DO NOTDO NOT DO NOT DO NOT
Do not ue into
natural draught
ues or replaces.
Do not ue into
other rooms.
Do not ue into
roof spaces.
Do not ue
under oor
spaces.
To ensure products of combustion
are cleared, adequate clearance
from the building is required. The
vertical cowl should have a
500 mm clearance from any part
of the building. This also applies to
steeped and pitched roofs, where
the ue cowl should be 500 mm
clear of the ridge line.
An adequate ow of fresh air must
exist around the ue cowl following
installation.
Minimum clearances are shown in AS/NZS 5601.1.
500 mm to
nearest
part of the
roof
6 | Linear ue installation guide 13541-A 01-20
Flueing options
For lowest cost, optimal performance, ease of installation and servicing, Rinnai
recommend short ue installations (less than 3 m) are considered before all other
options. Short ue installations are shown below.
300 mm min.
up to 3 m
300 mm min
300 mm Min
E
SPIPE9
0
0
ESWTERM
45° bends
LSFKIT01
ASPDFK
45° bends
E
SPIPE9
0
0
ESWTERM
ESWTERM
ESPIPE900
LSFKIT01
ASPDFK
LSFEXTKIT01
The gas pressures of the Linear are factory set for short ue installations (less than 3 m).
Installations greater than 3 m are long ue installations and will require a dip switch change, refer
commissioning instructions.
When considering the location of the re care must be taken to ensure the ue path is free from
obstructions such as studs, noggins, joist, braces, electrics etc.
Linear ue installation guide 13541-A 01-20 | 7
Side direct, sided extended, side and back ueing
Side direct through the wall ueing for walls up to 385 mm thick. Flue can be extended if the wall
thickness is greater than 385 mm by using additional lengths of ue pipe, and the pipe can be
directed behind by using the ue transition extension and bend kit.
Back direct and back extended ueing
By changing the direction of the adaption ue position and connection, back direct and back direct
extended ueing is possible.
1. Direct ue kit - ASPDFK 1. Direct ue kit - ASPDFK
2. Flue pipe - ESPIPE900
1. Direct ue kit - ASPDFK
2. Flue transition - LSFEXTKIT01
3. 45° bends - ESBEND
4. Flue pipe - ESPIPE900
1. Adaption ue - LSFKIT01
2. Wall terminal - ESWTERM
1. Adaption ue - LSFKIT01
2. Flue pipe - ESPIPE900
3. Wall terminal - ESWTERM
Maximum ue length and
number of bends
Maximum ue length = 8.5 m
Maximum number of bends = three
For every 90° bend, the overall length must be reduced by
1 m. For example, if an installation has three 90° bends, the
maximum flue length can be 5.5 m. The elbow component of
the Linear adaption flue kit (LSFKIT01) is not counted as a 90°
bend.
300 mm of straight ue
before any bends
A minimum of 300 mm of straight ue is required before any
bends. This is required due to the heat produced from the initial
section of ue. The LSFKIT01 has the 300 mm minimum ue
length built in.
If using the direct ue (ASPDFK) and connecting to any bends,
a ue transition extension (LSFEXKIT01) must be connected to
achieve the minimum length.
8 | Linear ue installation guide 13541-A 01-20
Up and back, and up and over ueing
Up and back through the wall ueing for walls up to 385 mm thick. Flue can be extended if the wall
thickness is greater than 385 mm by using additional lengths of ue pipe.
Down and out ueing
The down and out ue allows for the adaption ue to face downwards, and for the ue to run
vertically through a hole in the oor, and then to terminate horizontally outside.
Vertical ueing
The vertical in-wall ue installation is installed against an internal wall or
other suitable cavity, and is run vertically upwards to a vertical termination
above the roof.
1. Adaption ue - LSFKIT01
2. 45° bends - ESBEND
3. Flue pipe - ESPIPE900
4. Wall terminal - ESWTERM
1. Adaption ue - LSFKIT01
2. 45° bends - ESBEND
3. Flue pipe - ESPIPE900 x 2
4. Wall terminal - ESWTERM
1. Adaption ue - LSFKIT01
2. Flue pipe - ESPIPE900 x 2
3. 45° bends - ESBEND
4. Wall terminal - ESWTERM
5. Wall plate - ESPLATE (not shown)
1. Adaption ue - LSFKIT01
2. Flue pipe - ESPIPE900 x 3
3. 45° bends - ESBEND
4. Wall terminal - ESWTERM
5. Wall plate - ESPLATE (not shown)
1. Adaption ue - LSFKIT01
2. Flue pipe - ESPIPE900
3. Vertical terminal - ESROOFCOWL
Flueing options continued
Linear ue installation guide 13541-A 01-20 | 9
Air hose connection
This end of the exible
air hose comes already
connected to the air
inlet.
Rubber cap placed on
the unused air intake
Air intake hose
connected to the
LSFKIT01 and
secured with a cable tie
Flue lock bracket
holding the LSFKIT01
in place.
LSFKIT01 connected
into the Linear
combustion fan
exhaust.
This step in the installation is critical. If the connections are not secured properly, products
of combustion could disperse into the room being heated.
The Linear comes with one end of the exible air hose already connected to the Linear air inlet.
Attach the other end of the air intake hose to the connection on the flue, either the ASPDFK or the
LSFKIT01.
Connect the flue into the Linear combustion fan exhaust, and secure in place (two screws) with the
flue lock bracket (supplied in the plastic bag with the remote control).
Secure the air intake hose on the ue with the cable tie (supplied in the plastic bag with the remote
control), and ensure the rubber cap is in place on the unused air intake.
WARNING
Large air inlet
connection
LSFKIT01
Flue exhaust
connection
ASPDFK
Air inlet hose
Flue exhaust
locking bracket
Flue exhaust
connection
Small air inlet connection
(rubber cap MUST remain in place)
10 | Linear ue installation guide 13541-A 01-20
Flue components
540 mm
Ø 75 mm
50 mm
140 mm
Direct ue kit - ASPDFK (aluminium)
Suitable for walls up to 385 mm thick (can be cut to length). Can also
be used with ESPIPE900 for longer ueing. The minimum length when
measured from the back plate of the transition casting MUST NOT be less
than 300 mm when joining to other components.
Spacers are mandatory to
ensure alignment of the flue
and to stop the outer bends
overheating
45° ue bends - ESBEND
Two bends in a kit. Can be used
separately, or together as a 90° bend.
Refer additional images on p.19-20.
Adaption ue kit - LSFKIT01
Includes ue adaptor, ue extension,
stando bracket, ue slide stopper
(4822), O-ring silicone grease.
77 mm
475 mm
115 mm
Wall terminal kit - ESWTERM
Used to terminate the ESPIPE900
in horizontal ue installations when
used with LSFKIT01.
Transition extension - LSFEXTKIT01
Flue transition extension, MUST BE
used with the ASPDFK before any
bends, for example in side and back
ueing. When connected overall
length reduces 45 mm each end.
300 mm
Wall plate - ESPLATE
Used in down and out ueing to cover
the oor penetration, and also as an
extra wall cover if required, to tidy up an
installation. Outer diameter 170 mm.
Flue pipe - ESPIPE900
Extension pipe used for horizontal,
vertical, and downwards ueing. Can
be cut to size at the non-socketed
end.
Inner is aluminium, outer white PVC.
Comes with a wall bracket, o-ring
(4350), and spacer (4351).
975 mm
Roof terminal - ESROOFCOWL
Roof cowl and connecting pipe for
termination of a vertical ue—can
be cut to size. 500 mm clearance
required from any part of the
building, refer p.5.
Galvanised steel, powder coated
black.
Due to heat from the ue components, maintain 25 mm clearance to combustibles for the rst 500 mm of ue
Not pictured is the
internal white wall plate
Otros manuales para Linear Series
2
Tabla de contenidos
Otros manuales de Chimenea de interior de Rinnai
Rinnai
Rinnai RDV3610ETR Manual de usuario
Rinnai
Rinnai RHFE 750 Manual de usuario
Rinnai
Rinnai RDV600ER Manual de usuario
Rinnai
Rinnai Symmetry RDV3611 Manual de usuario
Rinnai
Rinnai LUMINA800BL Instrucciones de instalación y funcionamiento
Rinnai
Rinnai Arriva 752 Manual de usuario
Rinnai
Rinnai Royale FS35 ETR Manual de usuario
Rinnai
Rinnai ES750 Manual
Rinnai
Rinnai RF1200TW Manual de usuario
Rinnai
Rinnai Evolve 950 Manual de usuario
Rinnai
Rinnai FLAME FIRES Manual de usuario
Rinnai
Rinnai Symmetry RDV3611 Manual de usuario
Rinnai
Rinnai Linear 800 Manual de usuario
Rinnai
Rinnai Timberflame IB35 ETR Manual de usuario
Rinnai
Rinnai RDV600N Manual de usuario
Rinnai
Rinnai Linear 1000 Manual de usuario
Rinnai
Rinnai Symmetry RDV3610 Manual de usuario
Rinnai
Rinnai Ember Series Manual de usuario
Rinnai
Rinnai Neo RIB2311N Manual de usuario
Rinnai
Rinnai Symmetry RDV3611ETRN Manual de usuario
