Rinnai FS 35 Manual de usuario

Flame Fire

Operating and Installation Instructions

Freestanding Royale (Australia)

Timberﬂame FS 35 (New Zealand)

Table of Contents

Customer Instructions

Operation

Safety Points

Troubleshooting

Installation Instructions

Location

Flueing

Gas Connection

Log Installation

Testing & Commissioning

Technical Data

Service Contacts

Installation Checklist

Installer Details

IMPORTANT

This appliance shall be installed in accordance with:

•Manufacturers Installation Instructions.

•Local Gas ﬁtting regulations.

•Municipal Building codes.

•AGA Gas Installation Code AG601 - NZ 5261.

•Any other relevant statutory regulation.

•This appliance must only be installed, serviced and removed by an

authorised person.

•For Australian installation, this appliance must be installed with

the supplied wire dressguard.

LIMITED WARRANTY

TERMS AND CONDITIONS

1. During the 24 month period from date of purchase and subject to clauses 2 and 3 below,

Rinnai New Zealand Limited (“Rinnai”) will, at its own discretion, either replace or repair any

defective product at no charge to the customer.

2. This warranty covers manufacturing defects only. This warranty will not apply if (for example)

the product has been improperly installed or is otherwise installed contrary to manufacturer’s

recommendations, has been damaged during or after installation, has not been operated in

accordance with operating instructions, or has been subjected to damage or abuse beyond that

expected from conditions of normal use.

3. Warranty claims may be invalid if not accompanied by details of the installing or supervising

gas ﬁtter’s registration number and the gas ﬁtting certiﬁcation number.

4. This warranty commences from the date of purchase. Proof of purchase is required at the time

of any warranty claim.

5. Servicing of the product is to be carried out by a Rinnai authorised service centre.

All Rinnai appliances meet or exceed the safety standards required by New Zealand gas and electrical regulations.

The company is constantly improving its products and as such speciﬁcations are subject to change or variation

without notice.

Please keep these instructions in a safe place for future reference.

RECORD AND ATTACH YOUR PROOF OF PURCHASE BELOW:

Your Retailer:

Name:

Address:

Telephone: ( )

Date of Purchase: / /

1. Ignition/Low 16 MJ/h High / Off / Low

2. Medium 24 MJ/h High / Off / Low

3. High 35 MJ/h High (Auto)

For your convenience the controls on your new Flame Fire are situated under the cover

on the top right-hand side of the heater.

All necessary adjustments to the operation of your heater can be made with these controls.

•IGNITION

Press the front control button ﬁrmly. This operates the built-in

safety device and starts the electronic spark. The centre burner

will ignite. Check that the burner has lit and continue to hold the

button down for up to 15 seconds. The spark will continue while

the button is held down.

If the burner does not remain alight, push the button again and

release it. This will return it to the “OFF” position. Wait 30

seconds, then repeat the ignition procedure.

(The ignition button must be in the “OFF” position before attempt-

ing re-ignition).

•TO INCREASE THE HEAT

Press the control buttons in order from front to rear, this will ignite additional burners as

shown in the diagram.

There is no need to hold the buttons for 15 seconds when increasing the heat.

SETTING INPUT BUTTONS FAN BURNER PATTERN

•TO DECREASE THE HEAT

This is simply done by releasing the control buttons in order from rear to front.

•TO TURN THE UNIT OFF

Press and release the buttons in order from back to front until all 3 buttons are in the “OFF”

(UP) position. The fan will continue to operate until the heater cools off.

Ensure all burners are extinguished.

•POWER FAILURE

Your Rinnai Flame Fire can be used on the low and medium settings during a power failure.

However, if switched off, it cannot be relit unless power is available.

The appliance is protected by an overheat switch, and may cut out if used on the HIGH setting.

OPERATION

•FAN OPERATION

On the LOW and MEDIUM heater settings, the fan can be operated on the LOW speed or

OFF.

NOTE: When the heater is turned on, there will be a delay in the operation of the fan. This

ensures that a cold draft does not occur while the heater is warming up.

When the heater is turned off, the fan will continue to run until the heater has cooled down.

Do not restrict the warm air discharge by

placing articles in front of the heater.

This appliance must not be used for any pur-

pose other than heating.

Do not spray aerosols whilst the heater is

operating. Most aerosols contain butane gas,

and can be a ﬁre hazard if used near the heater

when it is in use.

Young children should be supervised at all

times. Hand or body contact with the louvres

should be avoided.

Do not allow young children or the inﬁrm to

sleep directly in front of the heater.

Do not allow anyone to sit on or lean

against the appliance.

Do not allow anyone to post articles

through the louvres.

Do not allow curtains or other ﬂammable

or combustible materials to come into

contact with the heater.

SAFETY POINTS

•NOTE:

If you have any other faults or problems, please refer to your Installer.

•OUTER CASE

The outer case of the heater should be cleaned with a soft, damp cloth.

Do not use aerosol polishes to clean the casing while the heater is in operation.

•CLEANING INSTRUCTIONS.

Before cleaning, ensure the power and gas are turned off and that the heater has

cooled down.

Do not remove any internal wiring covers.

Use only non abrasive cleaners.

Do not use solvent based cleaners.

•GLASS CLEANING

After a period of use the glass panel may require cleaning. When your heater is cold, refer to Page 8 and

follow the initial log installation instructions to remove side panels and glass for cleaning purposes.

TROUBLESHOOTING

SYMPTOM CAUSE SOLUTION

Burner will not light No power present Ensure power cord is plugged in

and turned on

Power cut Re-ignite after power is restored

Air in gas pipe Purge air (installer)

Ignition Failure Repeat lighting procedure

(refer page 2)

No gas present Ensure gas supply is turned on

Smell of gas Leaking gas Turn gas off at meter and

call installer

Fan not working Heat switch not

activated

Allow heater to run on HIGH

for 15 minutes minimum.

Fan not turned on Ensure appliance fan switch

is in ON position

Soot deposit forming

on Glass or Logs

Inadequate Flue System

Condensation on Glass Normal operation Allow heater to warm up

Streaky lines on Glass Normal operation Remove and clean Glass

Log Misalignment

Incorrect Gas Pressure

Call Rinnai Service Dept./Agent

Small Soot Deposit Normal operation No action required

YOur LOCATION

When positioning the heater, the main points governing the location are:

1. Flueing.

2. Warm air distribution.

3. The heater must not be installed where curtains or other combustible materials could come

into contact with it. In some cases, curtains may need restraining.

See below for minimum clearances required.

4. The heater is not designed to be built into bookcases or shelves or any combustible

opening.

5. Check that room ventilation complies with local regulations.

6. Check that an EARTHED power point is within 1500mm. of the right hand side of the

heater.

7. The heater does not require any additional hearth or ﬂoor protection.

FLUEING

•RUN GAS SUPPLY

For pipe sizing, refer to your local gas installation

codes.

Copper supply should be run leaving a ﬂared connection

at the position shown.

PURGE SUPPLY OF AIR AND SWARF.

All foreign materials such as ﬁlings must be purged

from the gas supply, as they may cause the gas valve to

malfunction.

Connect and tighten union.

On completion of work, check for gas leaks.

GAS CONNECTION

• This heater requires a minimum 3m. ﬂue.

• Position the heater.

• Suspend a plumbline from the ceiling to

the centre of the ﬂue socket.

• Mark the centre of the ﬂue in the ceiling.

• Make a small hole in the ceiling and double

check that the ﬂue system will be at least

25 mm clear of combustible materials.

• Cut the hole for the ﬂue.

• Fit the ceiling plate, ﬂue and decorative

cover.

The decorative cover must be able to slide up

to give access to the ﬂue spigot. The inner

ﬂue must be supported independently of the

heater but allowing sufﬁcient movement to

allow connections to and disconnections from

the ﬂue spigot.

LOG INSTALLATION

The logset is packed inside the heater and the packaging must be removed prior to

installing the logset in its correct position.

•Open both side panels.

•Remove fastenings on both sides of the

top glass retainer.

Lift retainer away from heater.

•Loosen screws on bottom glass retainer.

Carefully lift glass out of bottom channel.

•Carefully remove log packaging.

The logset consists of a Main Log which has four pins on the top, for the location of the Top and Right Logs

and two holes underneath for location onto the pins inside the heater.

Place the logset into the heater ensuring that the locating pins enter the two locating holes on

the bottom face of the logset, if not already attached.

Carefully position the Top Log and the Right Log on the locating pins of the Main Log as shown.

Gently place loose ember bed material in front of the front log. Do not pour as dust particles from

the plastic bag may block the burner ports. Level it with a pencil or screwdriver and remove excess ma-

terial. Note: The ember bed material must be placed after the logs are ﬁtted. If the logs are to be removed

for any reason, the ember bed material must be removed ﬁrst and replaced after the logs are reﬁtted. Any

material that prevents the logs sitting ﬂat on the burner top can upset the burning pattern and performance

of the heater.

• Replace glass and top glass retainer, tighten bottom glass retainer screws.

• Note: Fit glass so that the join/gap in the glass seal is at the bottom.

•Take care not to damage seals.

• Reinstall side panels.

Top Log Right Log

Main Log

Note: When ﬁrst lighting the heater, the logs need to be burnt in, which may take approximately 2

hours. The ﬂame colour may change after the initial burning in period.

vvvvv

Comple

TESTING & COMMISSIONING

TESTING PROCEDURE

Turn gas supply on and plug the unit into the power supply. (Caution 240V.)

•TO CHECK BURNER PRESSURE

•Refer to Data Plate.

•Remove test point screw and attach manometer to test point.

The test point is on the front side of the gas valve.

Light heater, push control buttons to the high position and

check pressure.

•If adjustments are necessary, the regulator is situated on

the front of the gas control.

•After checking pressure, turn the unit off, remove manometer and replace test point screw.

• Turn the heater on and off a few times to check ignition.

• When you are satisﬁed that the heater is working correctly, reassemble panels.

• All burner aeration is factory preset and cannot be adjusted.

• If you are unable to get the unit to operate correctly, refer to Troubleshooting on Page 5,

before contacting your local service agent as listed on Page 10.

• It may take approximately 2 hours for the logs to achieve their full ﬂame pattern and glow.

•During the initial burning in period, some smoke and smell may be experienced. The

heater should be run on the high position in a well ventilated room until these dissipate.

•INSTRUCT CUSTOMER ON USE OF UNIT

Explain to customer about use and care of unit. Make sure the customer understands the instructions.

•EXPLAIN

Ignition, Adjusting heat level, Fan Switch, Turning “OFF”.

COMMISSIONING

•INSTALLATION AND COMMISSIONING CHECKLIST

Complete the installation / commissioning checklist and the installer / gasﬁtter details on page 12 and

make sure that this instruction book is left with the customer.

NOTE:

RINNAI RESERVES THE RIGHT TO CHANGE OR MODIFY SPECIFICATIONS WITHOUT NOTICE.

Comple

Model:

Description:

Input:

Gas Control:

Burner:

Gas Inlet:

Test Point Pressure:

Flue:

Flue Termination:

Ignition:

Power Supply:

Fan:

Data Plate:

TECHNICAL DATA

FGL35 FBN (NG) Australia

FGL35 FBL (Propane) Australia

FS35N (NG) New Zealand

FS35L (Propane) New Zealand

Rinnai Inbuilt Radiant/Convector, glass-fronted, ceramic log space heater

with forced convection and natural draught ﬂue system.

35 MJ/h Natural Gas and Propane.

Rinnai Push-Button Combination Control.

Ceramic Logs, Ember Bed and Heat Burner.

15mm. Copper Flare Connection.

Natural Gas 0.95 kPa; Propane 2.60 kPa.

Natural Draught.

An approved 100mm. cowl must be ﬁtted

to all installations.

Electronic Spark.

230/240v. 50Hz unit is supplied with 3 pin

plug and supply lead, replace only with

Rinnai P/N 90179599(Aust.) 6765B(NZ).

Tangential 2 Speed, Watt Rating 90W.

Bottom R/H side of pillar.

SERVICE CONTACT POINTS

RINNAI AUSTRALIA PTY. LTD. ACN. 005 138 769

Helpline: 1300 366 388

Mon.-Fri (8.30am-5.30pm EST)

(Cost of a local call - higher from mobile or public phones)

Internet: www.rinnai.com.au

Email: [email protected]

VIC./TAS:

Head Ofﬁce:10-11 Walker St. Braeside, Vic. 3195

Tel.(03) 9271 6625 Fax.(03) 9271 6622

Sales Tel.(03) 9271 6666 Fax.(03) 9271 6611

Service Tel.(03) 9271 6699 Fax.(03) 9271 6688

NSW./ACT: 62 Elizabeth St. Wetherill Park, NSW 2164

Tel. (02) 9609 2888 Fax. (02) 9729 5260

SA./NT: 140 Days Rd. Ferryden Park, SA. 5010

Tel. (08) 8345 0292 Fax. (08) 8345 4760

WA: 18 Belgravia St. Belmont, WA. 6104

Tel. (08) 9478 3355 Fax. (08) 9277 2531

QLD: 1/6 Booran Drive, Logan Central, Qld. 4114

Tel. (07) 3209 4622 Fax. (07) 3209 4722

RINNAI NEW ZEALAND LTD. Internet: www.rinnai.co.nz

Email: [email protected]

105 Pavilion Drive, Airport Oaks, Mangere, Auckland, NZ.

PO Box 53177, Auckland Airport, Manukau, 2150 Tel. +64 9 257 3800 Fax. +64 9 257 3899

24 Hr. Service Tel. 0800 867 46624 (0800 TORINNAI)

Tabla de contenidos

Otros manuales de Chimenea de interior de Rinnai

Rinnai

Rinnai Evolve 952 Series Manual de usuario

Rinnai

Rinnai RHFE-1252ER Manual de usuario

Rinnai

Rinnai Novo Manual de usuario

Rinnai

Rinnai Ember 600 Manual de usuario

Rinnai

Rinnai Neo Manual de usuario

Rinnai

Rinnai Symmetry RDV3611 Manual de usuario

Rinnai

Rinnai RHFE-750ETRA Manual de usuario

Rinnai

Rinnai Neo RIB2311L Manual de usuario

Rinnai

Rinnai Royale FS35 ETR Manual de usuario

Rinnai

Rinnai IB35R Manual de usuario

Rinnai

Rinnai Neo RIB2311N Manual de usuario

Rinnai

Rinnai RF800 Manual de usuario

Rinnai

Rinnai Novo Cube Manual de usuario

Rinnai

Rinnai Slimline 2 Manual de usuario

Rinnai

Rinnai Symmetry RDV3611 Especificaciones técnicas

Rinnai

Rinnai Symmetry RDV3610 Manual de usuario

Rinnai

Rinnai RIBF25N Manual de usuario

Rinnai

Rinnai Arriva Hoja de especificaciones

Rinnai

Rinnai RHFE1000 Manual de usuario

Rinnai

Rinnai Evolve 950 Manual de usuario

Rinnai

Rinnai Symmetry RDV3600 Manual de usuario

Rinnai

Rinnai Symmetry RDV3611 Manual de usuario

Rinnai

Rinnai RHFE 750 Manual de usuario

Rinnai

Rinnai SS850ICLN Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación