Rimage Everest II Manual de usuario
Rimage Printer Family™ Operator
2000466_B © 2007, Rimage Corporation 1
Replace the Ink Ribbon Base Plate in an Everest II Printer
Use this procedure to replace the ink ribbon base plate in an Everest II™.
Rimage approved parts must be used for this process. The product warranty may become void if parts not approved by Rimage are
used; equipment or parts are tampered with, misused, neglected, or modified in any respect without the written consent of Rimage.
Notes:
•Your system may not look exactly like the system pictured.
•The term “Everest” is used throughout this document to refer to the Everest II only.
#Required tools:
Before you begin
1. Stop or pause all jobs. •Long-shaft Phillips #2 screwdriver
2. If the printer is attached to an autoloader, power off the •Small flathead screwdriver
autoloader.
3. Disconnect the power cord from the power outlet. •Needle-nose pliers
Remove the Ink Ribbon Base Plate
1. Disconnect all cables from the printer.
nCaution! Some cables in this system are latched.
Equipment damage may occur if cables are not
disconnected appropriately.
•Printer cable (if on an autoloader)
•USB cable
•Power cord
2. If the printer is on an autoloader, remove it from the
autoloader.
nCaution! Lift the printer with care. It is very heavy.
Printer Cable USB Cable
Power Cord
3. Access the ink ribbon base plate.
a. Press the two cover latches to release the ribbon
access cover.
b. Lower the ribbon access cover.
Ribbon Access Cover
atches
Cover L
Replace the Ink Ribbon Base Plate in an Everest II Printer Everest II™
2000466_B © 2007, Rimage Corporation 2
c. Open latch 1 as shown.
d. Remove the print ribbon carrier.
4. Manually slide the printer tray all the way out of the printer.
a. Open the printer tray door.
Tip: Use a small flathead screwdriver to open the
door.
b. Grasp the front of the printer tray with a needle-
nose pliers and firmly pull out the tray.
5. Remove the ink ribbon base plate.
a. Remove the Phillips screws (Qty. 2) at the front of the
ink ribbon base plate.
b. Remove the Phillips screw at the back of the ink ribbon
base plate using a long-shaft Phillips screwdriver.
Latch 1
Print Ribbo
Carrier n
Ink Ribbon
Base Plate
Printer Tray
Door
Ink Ribbon Base Plate
Replace the Ink Ribbon Base Plate in an Everest II Printer Everest II™
2000466_B © 2007, Rimage Corporation 3
6. Lift the ink ribbon base plate up to unlatch it.
7. Keeping the plate at an angle, carefully remove the ink
ribbon base plate from the printer.
nCaution! Do not scratch the platen roller.
Install the Ink Ribbon Base Plate
1. While holding the replacement ink ribbon base plate at a
slight angle, carefully position the ink ribbon base plate in the
printer.
nCaution! Do not scratch the platen roller.
-Important! The lip on the ink ribbon base plate must be
positioned as shown on the printer frame.
Platen Roller
Lip
Printer Frame
Replace the Ink Ribbon Base Plate in an Everest II Printer Everest II™
2000466_B © 2007, Rimage Corporation 4
2. Install the Phillips screws (Qty. 3) to secure the ink ribbon
base plate.
Tip: One of the screws fits into the tab at the back of the
ink ribbon base plate, inside the printer.
Prepare the Printer for Use
1. Insert the print ribbon carrier.
2. Close latch 1.
3. If necessary, place the printer onto the autoloader.
nCaution! Lift the printer with care. It is very heavy.
4. Connect the cables to the rear of the printer.
•USB cable
•Printer cable (if on an autoloader)
•Power cord
The printer is ready for use.
Support information
Europe When you contact Rimage Services, please provide:
Contact Rimage Services Europe:
www.rimage.com/support.html
Email: [email protected]
Tel: +49-(0) 6074-8521-0
•Unit serial number and software version.
•Functional and technical description of the problem.
•Exact error message received.
US, Asia/Pacific, Mexico/Latin America
Contact Rimage Services:
www.rimage.com/support.html
Email: http://www.rimage.com/support_form.cfm
Tel: North America: 800-553-8312
Asia/Pacific, Mexico/ Latin America: 952-946-0004
Rimage Corporation reserves the right to make improvements to the
equipment and software described in this document at any time without
any prior notice. Rimage Corporation reserves the right to revise this
publication and to make changes from time to time in the content hereof
without obligation of Rimage Corporation to notify any person or
organization of such revisions or changes.
Ink Ribbon Base Plate
Latch 1
Print Ribbo
Carrier n
Tabla de contenidos
Otros manuales de Impresora de Rimage
Rimage
Rimage Everest 600 Manual de usuario
Rimage
Rimage Professional 3400 Manual de usuario
Rimage
Rimage Prism Manual de usuario
Rimage
Rimage Prism CDPR11 Manual de usuario
Rimage
Rimage CDPR6 Manual de usuario
Rimage
Rimage Everest Manual de usuario
Rimage
Rimage Desktop 360i Manual de referencia
Rimage
Rimage Everest Manual de usuario
Rimage
Rimage Everest 600 Manual de usuario
Rimage
Rimage Professional 3400 Manual de usuario
Rimage
Rimage Prism III Manual de usuario
Rimage
Rimage AutoPrism Instrucciones de funcionamiento y seguridad
Rimage
Rimage Amigo II Manual de usuario
Rimage
Rimage Everest 600 Manual de usuario
Rimage
Rimage Autostar II Manual de usuario
Rimage
Rimage Prism III Manual de usuario
Rimage
Rimage Producer IIIN+ 8100N Manual de usuario
Rimage
Rimage Amigo II Manual de usuario
Rimage
Rimage Amigo II Manual de usuario
Rimage
Rimage Amigo II Instrucciones de instalación
