Rimage Everest II Instrucciones de instalación

Align the Everest II Printer

When the Everest printer is installed, it may need to be aligned to the lift arm.

Tools Needed: T25 Torx driver

Before you begin:

 Install the Everest Printer

 Power on the Rimage DiscLab. Wait for the unit to initialize.

 Note: The Everest printer takes 2 to 3 minutes to complete the initialization.

1. Select Diagnostic 4, Jog Lift Diagnostic.

a. Press and hold the Operator Button to place the unit in diagnostics mode. The Operator

Panel indicates when to release the button.

b. When the Operator Panel displays 01 CYCLE OUTPUTS DIAGNOSTIC, press the Operator

Button four times and hold on the fourth press. This selects the JOG LIFT DIAGNOSTIC

TEST. The Lift Arm moves down toward the Print Drawer as the Print Drawer opens.

c. When the Operator Panel prompts you to place a disc, place a disc on the print pad.

2. Check the printer alignment.

a. Press the Operator Button to move the Lift Arm closer to the Print Pad.

b. Press the Operator Button again and the Lift Arm moves down and picks up the disc.

c. Manually rotate the Lead Screw counterclockwise to move the Lift Arm down to the Print Pad.

3. Check the disc alignment.

To see if the disc is centered, observe the gap

between the edge of the disc and the raised edges

as shown by the arrows.

If the disc is not centered side-to-side on the Print

Pad, continue to step 3.

If the side-to-side alignment is correct, go to step

Lift Arm

Print Pad

Disc

Lead Screw

Print Pad

Print Drawer

112063_A October 29, 2004 1

Align the Everest II Printer

3. If necessary, perform a side-to-side alignment.

a. Loosen the two torx side-to-side alignment

screws.

b. Slide the printer until the side gaps are equal.

-Important! Slide the entire printer, not the drawer.

c. Tighten the two side-to-side alignment screws.

Front to back alignment screw

Side-to-side alignment screws

4. If necessary, perform a front-to-back alignment.

a. Turn the front-to-back alignment screw until

there is a 1/16” (1.5mm) gap between the

front edge of the disc and the raised edge of

the Disc Retainer.

 Tip: You can use the T25 Torx driver, or 5/32”

Allen wrench, to turn the front-to-back alignment

screw.

b. When the printer is aligned, rotate the Lead

Screw to raise the Lift Arm up about 1.0” (2.5

cm).

5. Exit diagnostics.

a. Press and hold the Operator Button to exit

Diagnostic Test 4. The disc is lifted up to the

top output tray and released.

b. Press the Operator Button fourteen times and

hold on the last press to exit Diagnostics.

c. Press the Operator Button one more time to

close the Print Drawer.

Disc Retainer

Distance

Lift Arm

Print Pad

Lead Screw

112063_A October 29, 2004 2

Tabla de contenidos

Otros manuales de Impresora de Rimage

Rimage

Rimage Allegro 100 Manual de usuario

Rimage

Rimage Everest Encore Instrucciones de funcionamiento y seguridad

Rimage

Rimage Everest 600 Manual de usuario

Rimage

Rimage AutoEverest AutoPrinter Manual de usuario

Rimage

Rimage Everest II Manual de usuario

Rimage

Rimage Desktop 360i Manual de usuario

Rimage

Rimage 5400N Disc Copy Station Manual de usuario

Rimage

Rimage CDPR6 Manual de usuario

Rimage

Rimage Prism Manual de usuario

Rimage

Rimage Everest III Manual de usuario

Rimage

Rimage Amigo II Manual de usuario

Rimage

Rimage Desktop 360i Manual de usuario

Rimage

Rimage Prism III Manual de usuario

Rimage

Rimage Autostar II Manual de usuario

Rimage

Rimage Prism Manual de usuario

Rimage

Rimage Desktop 360i Manual de usuario

Rimage

Rimage Autostar II Manual de usuario

Rimage

Rimage Desktop 360i Manual

Rimage

Rimage Producer IIIN+ 8100N Manual de usuario

Rimage

Rimage Desktop 360i Manual de uso y cuidado

Rimage

Rimage Professional 3400 Manual de usuario

Rimage

Rimage Everest Encore Manual de usuario

Rimage

Rimage Desktop 360i Instrucciones de funcionamiento y seguridad

Rimage

Rimage Everest 600 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario