Rigol DS1102E Manual de usuario
Quick Guide RIGOL
Publication Number QGA07116-1110
Jun 2013
DS1000E, DS1000D Series
Digital Oscilloscope
DS1102E, DS1052E, DS1102D, DS1052D
© 2008 RIGOL Technologies, Inc.
All Rights Reserved
RIGOL
Quick Guide for DS1000E, DS1000D Series I
Copyright
© 2008 RIGOL Technologies, Inc. All Rights Reserved.
RIGOL products are protected by patent laws in and outside of
the P.R. China.
Information in this publication replaces all previous
corresponding material.
RIGOL reserves the right to modify or change part of or all the
specifications and pricing policies at company’s sole decision.
NOTE:
RIGOL is registered trademark of RIGOL Technologies, Inc.
RIGOL
Quick Guide for DS1000E, DS1000D Series
II
Safety Notice
Review the following safety precautions carefully to avoid any
personal injuries or damages to the instrument and any products
connected to it. To avoid potential hazards, please use the
instrument as specified by this manual only.
The instrument should be serviced by Authorized personnel
only.
To Avoid Fire or Personal Injury.
Use Proper Power Cord. Use the power cord designed for the
instrument and authorized in your country only.
Connect and Disconnect Logic Analyzer. Do not connect or
disconnect logic Analyzer while the instrument is powered on.
Ground The Instrument. The oscilloscope is grounded through
the grounding conductor of the power cord. To avoid electric shock
the instrument, grounding conductor(s) must be grounded properly,
before making connections to the input or output terminals of the
instrument.
Connect The Probe. The probes’ ground terminals are at the
same voltage level of the instrument ground. Do not connect the
ground terminals to a high voltage.
Observe All Terminal Ratings. To avoid fire or shock hazard,
observe all ratings and marks on the instrument. Follow the user’s
guide for further ratings information before making connections to
the instrument.
Do Not Operate Without Covers. Do not operate the instrument
with covers or panels removed.
Avoid Circuit or Wire Exposure. Do not touch exposed
connections and components when power is on.
Do Not Operate With Suspected Failures. If suspected damage
occurs with the instrument, have it inspected by qualified service
RIGOL
Quick Guide for DS1000E, DS1000D Series III
personnel before further operations.
Provide Proper Ventilation. Refer to the installation instructions
for proper ventilation of the instrument.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
The disturbance test of all the models meet the limit values
of A in the standard of EN 61326: 1997+A1+A2+A3, but
can’t meet the limit values of B.
Measurement Category
The DS1000E, DS1000D series Digital Oscilloscope is intended to be
used for measurements in Measurement Category I.
Measurement Category Definitions
Measurement Category I is for measurements performed on circuits
not directly connected to MAINS. Examples are measurements on
circuits not derived from MAINS, and specially protected (internal)
MAINS derived circuits. In the latter case, transient stresses are
variable; for that reason, the transient withstand capability of the
equipment is made known to the user.
WARNING
IEC Measurement Category I. The input terminals may be
connected to circuit terminal in IEC Category I installations for
voltages up to 300Vrms. To avoid the danger of electric shock, do
not connect the inputs to circuit’s voltages above 300Vrms.
Transient overvoltage is also present on circuits that are isolated
from mains. The DS1000E, DS1000D series Digital Oscilloscopes is
designed to safely withstand occasional transient overvoltage up to
1000Vpk. Do not use this equipment to measure circuits where
transient overvoltage could exceed this level.
RIGOL
Quick Guide for DS1000E, DS1000D Series
IV
Safety Terms and Symbols
Terms in This Guide. These terms may appear in this manual:
WARNING: Warning statements indicate the conditions
or practices that could result in injury or loss of life.
CAUTION: Caution statements indicate the conditions or
practices that could result in damage to this product or
other property.
Terms on the Product. These terms may appear on the product:
DANGER indicates an injury or hazard that may be immediately
happen.
WARNING indicates an injury or hazard that may be not
immediately happen.
CAUTION indicates that a potential damage to the instrument or
other property might occur.
Symbols on the Product. These symbols may appear on the
product:
!
!
!
Hazardous
Voltage
Refer to
Instructions
Protective
Earth
Terminal
Earth
Ground
Chassis
Ground
RIGOL
Quick Guide for DS1000E, DS1000D Series V
Contents
Contents.................................................................................. V
Necessary Inspection................................................................ 1
How to Connect Power Cord...................................................... 2
How to Connect Probe or BNC................................................... 3
How to Connect Logic Analyzer ................................................. 5
How to Connect USB and RS232 Devices.................................... 6
Troubleshooting........................................................................ 7
Contact Us............................................................................... 9
RIGOL
Quick Guide for DS1000E, DS1000D Series 1
Necessary Inspection
1．Inspect the shipping container for damage.
Keep the damaged shipping container or cushioning material
until the contents of the shipment have been checked for
completeness and the instrument has been checked
mechanically and electrically.
2．Inspect the instrument.
In case there is any mechanical damage or defect, notify the
RIGOL Sales Representative. If the shipping container is
damaged, or the cushioning materials show signs of stress,
notify the carrier as well as the RIGOL sales office. Keep the
shipping materials for the carrier’s inspection.
3．Check the accessories.
Please check the accessories according to packing list. If the
contents are incomplete or damaged notify the RIGOL Sales
Representative.
RIGOL
Quick Guide for DS1000E, DS1000D Series
2
How to Connect Power Cord
After inspecting the instrument and the accessories, connect the
power cord as shown in the following figure.
Press the power key on the top of the oscilloscope. if the
oscilloscope can not be powered on, check the power cord
connection. If the oscilloscope still can not start up after the
inspections, please contact RIGOL for help.
Otros manuales para DS1102E
2
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Equipo de prueba de Rigol
Rigol
Rigol RP7080S Manual de usuario
Rigol
Rigol DS1000Z-E Series Manual de usuario
Rigol
Rigol DS1000CA series Manual de usuario
Rigol
Rigol DS8000-R Series Manual de usuario
Rigol
Rigol DS4024E Manual de usuario
Rigol
Rigol DS4024 Manual de usuario
Rigol
Rigol DS6000 Series Manual de usuario
Rigol
Rigol DHO1000 Series Manual de usuario
Rigol
Rigol MSO2000A Series Manual de usuario
Rigol
Rigol DG800 Pro Series Instrucciones de funcionamiento
Rigol
Rigol DS1104Z-S Plus Manual de usuario
Rigol
Rigol DS1000Z Series Instrucciones de funcionamiento
Rigol
Rigol MSO5000 Series Manual de usuario
Rigol
Rigol DS6000 Series Manual de usuario
Rigol
Rigol DS2000E Series Manual de usuario
Rigol
Rigol DS2000A Series Manual de usuario
Rigol
Rigol RP5600A Manual de usuario
Rigol
Rigol DS8000-R Series Manual de usuario
Rigol
Rigol DS2000 Series Manual de usuario
Rigol
Rigol MSO1000Z series Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
