Ricoh MPC 1500sp Manual de usuario
MPC 1500sp
Technicians
Troubleshooting Guide
This guide is designed to help you with known issues.
Produced by M. Drage v1.2
White or Coloured Lines
Before completing any of the following, REMOVE AND
CLEAN THE MAINTENANCE UNIT. Pay particular
attention to the wiper area, the roller and first cap.
CLEAN ONLY WITH A CLOTH DAMPENED WITH
WATER - NO CHEMICALS!
Once the above has been completed, move onto head cleaning or flushing.
Select User tools, Maintenance, Head Cleaning or Flushing.
To check which print head is blocked use the Nozzle Check Pattern.
To clean, select CLEAN from the menu - you will have a check box by each
colour. Use the right arrow to select and the down arrow to move onto the
next item.
This is a good one
This shows that the black and cyan print heads are blocked
Sometimes you will have to perform head cleaning more than once to
resolve the issue. If after 4 head cleans, you still have a problem, then try
head flushing. If after this, there is still an issue, then try physically cleaning
the heads.
ONLY USE SPECIALISED HEAD CLEANING CLOTHS
PART NUMBER B2299311
If this is happening regularly there are a few options you can try depending
on when the lines appear.
1. If the symptom occurs when a printout is made after leaving the
machine unused for a long time, make sure the Engine Firmware is
v1.10 or later. This will ensure the head home position is correct, thus
ensuring the heads are capped correctly on the maintenance unit.
2. Make sure the carriage slide is in the correct position. If it is not then,
as previously the heads will not cap correctly, thus drying out. Use
the following guide to check and adjust.
Correct position Incorrect position
Release the lock for the maintenance unit. To do this turn the adjuster clockwise until the
heads of the triangles line up.
Slide the carriage until the small white part in the photo lines up with the hole.
Lift up the carriage unit and insert a small slot screwdriver into the hole and push until
you hear a click.
If the carriage slide is out of position you may get SC202 and/or jams in
areas A/C.
3. If the machine is installed in an environment with a relative humidity
of 15% or less, the ink will dry out quicker, as this is outside of the
machines operational specification and the machine will have to be
moved to a more suitable environment.
4. If the symptom occurs during regular use, then set SP2 508 001
(Exhalation Interval Change) to a value of 1 (every 15 seconds), also
do ONE of the following:
Set bit 6 of SP3 112 004 (print mode setting1) to a value of 1.
Ink mist can easily be generated when using paper with a high surface
impedance such as recycled paper. This mist can clog the nozzles.
Or
Change the setting of SP3 112 004 (print mode setting 4), so that auto
shading is performed more often.
xxxxx000: Default (1 time per approx 300 pages)
xxxxx001:1.3 times
xxxxx002:2 times
xxxxx003:4 times
xxxxx004:10 times. Remember, the more times it cleans, the
slower the print.
5. Each visit, clean the maintenance unit, if you have tried all of the
above you may have to replace the maintenance unit.
Smudged images
This is usually caused when the customer copies or prints onto unsuitable
paper. If the paper is not absorbent enough, the ink cannot dry before the
print head returns. Unfortunately there is no hard and fast rule as to the type
of paper that should be used - it is just a matter of trial and error.
Smudged copies can also occur if the paper is too thick. This product is able
to feed up to 105gms from the trays, 162gms from the bypass and 220gms
from the one sheet bypass. If the customer is using 220gms paper, then the
envelope lever may have to be used (in the down position), this will raise the
print head by about 2mm giving more clearance. Make sure the lever is put
back to normal (up position) as this may cause quality issues when using
normal paper.
Envelope lever
Grainy colour images, colour registration problems,
uneven shading in b/w mode and jagged lines
These issues are usually caused when the print heads are out of alignment.
Grainy Colour Images
Out of adjustment Correctly adjusted
Colour Registration
Out of adjustment Correctly adjusted
Out of Adjustment Jagged Lines
Correctly adjusted
Uneven Shading in B/W Mode
Out of adjustment Correct adjustment
Before any adjustments are made, please ensure that
you have completed the head cleaning successfully.
To do the adjustment, select User tools, to Maintenance, OK, to
Adjustments, OK. The first adjustment that is displayed is Head Position
Adjustment, OK. There are 2 adjustments to be made, Standard and High
Speed. PLEASE DO BOTH .You will be asked to print out the test page.
YOU WILL NEED A4r Paper in the machine, if there is only 1 cassette
you CAN use the bypass.
This is the test pattern produced in standard mode.
You will notice that you have an adjust option on the display. Select this and
the screen will now show the letters A to I with A highlighted.
Look at A on the test pattern above, if the heads are aligned correctly then
the 2 lines circled in red beneath 0 would be straight, the box would also be
light grey. The above pattern is out of adjustment and the correct setting is
+3 (circled in blue).
To change the setting for A, make sure that A is highlighted on the screen
and press OK. In our case press the + key 3 times, + 3 is now on the screen,
press OK. Check and follow the same procedure for all the letters.
Once this is complete, select END and this will take you back to the
maintenance menu, press OK and reprint the test pattern and check it, this
adjustment may have to done again, especially if it was a long way out.
When the standard adjustment is complete, follow the same procedure for
the high speed mode, the test pattern is slightly easier to see.
Once the above is complete, copy your test chart in B/W mode ensuring that
the grey band A is copied.
Look at this band on your copy. If it is uniform, no further action is required.
If, however you have either of the following 2 effects, further fine
adjustment is required.
1 2
To adjust, enter SP mode 3-002-010 (A).Make a note of the value (the
number above the figure in brackets). Also, go to 3-002-017(H) and
3-002-018 (I) and perform the same adjustment.
Complete the calculation I-A=H. As you have one of the above patterns I-A
will not equal H
Example I = 5, A = 3 H = 3 I – A = 2
If the image is the same as diagram 1above then adjust I, e.g. change I to 6
and this will make the calculation correct.
If the image is the same as diagram 2above, then adjust H, e.g. change H to
2.
In some cases when the formula is correct, you may still have a slight
variation, unfortunately there is nothing else you can do.
White or Dark Lines, Even After Head Cleaning Has
Been Performed.
Please ensure that you have completed head cleaning before doing this
adjustment.
To access the set up, press user tools, until Maintenance, OK , until
adjustment, OK until adjustment, OK, until Paper Feed Adjust and
press OK. You will now be asked to print a test pattern again – please ensure
that you have A4R paper loaded in the machine.
This is the test pattern generated. Ideally 0 should have the clearest box and
the straightest lines. In this case, 2 has the clearest box and straightest line.
Otros manuales para MPC 1500sp
1
Tabla de contenidos
Otros manuales de Copiador de Ricoh
Ricoh
Ricoh FT4422 Manual de usuario
Ricoh
Ricoh Aficio DSm616 Manual de usuario
Ricoh
Ricoh D069 Guía de inicio rápido
Ricoh
Ricoh D146 Manual de usuario
Ricoh
Ricoh MP 2014 Series Manual de usuario
Ricoh
Ricoh A193 Manual de usuario
Ricoh
Ricoh Aficio FX10 Manual de usuario
Ricoh
Ricoh M5 Manual de usuario
Ricoh
Ricoh PE-P1 Manual de usuario
Ricoh
Ricoh Priport DD 4450 Manual de usuario
Ricoh
Ricoh A229 Manual de usuario
Ricoh
Ricoh Aficio 1075 Manual de usuario
Ricoh
Ricoh FT7060 Guía de inicio rápido
Ricoh
Ricoh Aficio MP 1600L Manual de usuario
Ricoh
Ricoh PS430 Manual de usuario
Ricoh
Ricoh FW870 Manual de usuario
Ricoh
Ricoh MP 2014 Series Manual de usuario
Ricoh
Ricoh M022 Instrucciones de instalación
Ricoh
Ricoh A069 Manual de usuario
Ricoh
Ricoh TH-C1b Manual de usuario
