Richmond GTR099 Manual de usuario
GTR099 swing gate opener manual – Revision 22 1
Swing Gate Opener
User’s Manual
For Model: GTR099
• Please read and follow all warnings, precautions and instructions before installation and use.
• 2 x 12V 7Ah batteries are supplied. The AC adaptor included, is used to maintain charge in the batteries.
• Periodic checks of the operator are required to ensure safe operation
• Save this manual for future reference
GTR099 swing gate opener manual – Revision 22 2
Table of Contents
Safety Installation Information .......................................................................................................... 3
Parts List ............................................................................................................................................. 4
Optional Accessories Parts List........................................................................................................... 5
Tools Needed: .................................................................................................................................... 5
Technical Specifications & Features ................................................................................................... 6
Installation Overview ......................................................................................................................... 9
Preparation for Installation ................................................................................................................ 9
Install the Gate Opener on the Gate .................................................................................................. 10
Mounting of the control box ............................................................................................................. 16
Connection of the power supply ....................................................................................................... 16
Connection of the control board ....................................................................................................... 18
How to Program the Remote to the Opener ..................................................................................... 20
How to Erase All the Remote Codes .................................................................................................. 20
Setting of the Control Board .............................................................................................................. 21
Trouble Shooting ................................................................................................................................ 23
GTR099 swing gate opener manual – Revision 22 3
Safety Installation Information
1. READ and FOLLOW all instructions.
2. The gate opener is intended for use with Class I
vehicular swing gates. Class I denotes a vehicular gate
opener (or system) dwelling, or a garage or parking
area associated therewith. Install the gate opener only
when the opener is appropriate for the construction
and the usage class of the gate.
3. Gate opening system designers, installers and users
must consider the possible hazards associated with
each individual application. Improperly designed,
installed, or maintained systems can create risks for
the user as well as the bystander. Gate system design
and installation must reduce public exposure to
potential hazards. All exposed pinch points must be
eliminated or guarded.
4. A gate opener can create high levels of force during
normal operation. Therefore, safety features must be
incorporated into every installation. Specific safety
features include safety sensors.
5. The gate must be properly installed and work freely in
both directions prior to the installation of the gate
opener.
6. The gate must be installed in a location so that enough
clearance is provided between the gate and adjacent
structure when opening and closing to reduce the risk
of entrapment. Swinging gates shall not open into
public access areas.
7. The opener is intended for use only on gates used for
vehicles. Pedestrians must be supplied with a separate
access opening. The pedestrian access opening shall
be designed to promote pedestrian usage. The
pedestrian access shall be located such that persons
will not come in contact with the moving vehicular
gate.
8. Pedestrians should never cross the pathway of a
moving gate. The gate opener is not acceptable for
use on any pedestrian gate. Pedestrians must be
supplied with a separate pedestrian access.
9. For an installation utilizing non-contact sensors
(safety sensors), see product manual on the
placement of non-contact sensors (safety sensors) for
each type of application.
a. Care shall be exercised to reduce the risk of
nuisance tripping, such as when a vehicle trips the
safety sensor while the gate is still moving.
b. One or more non-contact sensors (safety sensors)
shall be located where the risk of entrapment of
obstruction exists, such as the perimeter reachable by
a moving gate or barrier.
10. Never mount any device that operates the gate
opener where the user can reach over, under, around
or through the gate to operate the controls. Controls
are to be placed at least 6’ (1.8m) from any part of the
moving gate.
11. Controls intended to be used to reset an operator
after 2 sequential activations of the entrapment
protection device or devices must be located in the
line of sight of the gate, or easily accessible controls
shall have a security feature to prevent unauthorized
use. Never allow anyone to hang on or ride the gate
during the entire travel of the gate.
12. Each gate opener is provided with two safety warning
placards. The placards are to be installed on the front
and back of the gate where they are plainly visible.
The placards may be mounted using cable ties through
the four holes provided on each placard. All warning
signs and placards must be installed where visible near
the gate.
13. To AVOID damaging gas, power, or other underground
utility lines, contact underground utility locating
companies BEFORE digging.
SAVE INSTRUCTION
14. Do not permit children to play on or around the gate
and keep all controls out of their reach.
GTR099 swing gate opener manual – Revision 22 4
Parts List
GTR099 swing gate opener manual – Revision 22 5
Optional Accessories
Tools Needed
Power Drill
Tape Measure
Open End Wrenches — 14mm & 17mm or Adjustable Wrenches
Wire Strippers
C-Clamps — small, medium, and large
Level
Hacksaw or Heavy Duty Bolt Cutters
Phillips Screwdriver
An extra person will be helpful
GTR099 swing gate opener manual – Revision 22 6
Technical Specifications & Features
Dimensions
Retracted Gate Arm Dimensions:
Extended Gate Arm Dimensions:
Specifications – GTR099
Fuse F5L250V or F5AL250V
Input: 120V/60Hz or 230V/50Hz
Motor voltage: 24VDC
Power: 80W
Current: 3A
Actuator speed: 16mm/s
Max. actuator travel: 385mm
Ambient temperature: -20
℃
~ +50
℃
(-4°F to 122°F)
Protection class: IP44
GTR099 swing gate opener manual – Revision 22 7
Dimensions
Gate Bracket Dimensions:
Post Bracket Dimensions:
Post Pivot Bracket Dimensions:
GTR099 swing gate opener manual – Revision 22 8
Gate Capacity of GTR099
Features
Soft start and soft stop
Emergency release key in case of power failure
Stop in case of obstruction during gate opening.
Reverse in case of obstruction during gate closing.
Built in adjustable auto-close (0-100 seconds)
Built in max. Motor running time (MRT) for additional safety protection (40 seconds)
Reliable electromagnetic limit switches for easy adjustment
Can be equipped with a wide range of accessories.
GTR099 swing gate opener manual – Revision 22 9
Installation Overview
Preparation for Installation
There are two installation types for the gate opener, Pull-to-Open and Push-to-Open. In the Push-to-Open
installation, gate opens out from the property. A Push-To-Open Bracket (GTR059) is required to be used for
each gate.
The gate opener is mounted to the gate and to the gate post. Both round and square posts can be used because
the Post Brackets are curved. When mounting the Post Brackets, use bolts long enough to pass through the entire
post. M10 x 200 bolts are included. Concrete anchors are not provided.
When mounting the Post Brackets to wooden posts, a larger-size washer or metal plate should be used between
the bolts and the wooden post to ensure the stability of the fastening hardware. If the post is smaller than 6"
diameter or square, it should be made of metal and set in cement to ensure its stability.
NOTE: Ensure the gate does not open into public areas.
Note:
for best performance
we always recommend
attaching the arm to the
centre of the gate.
GTR099 swing gate opener manual – Revision 22 10
Install the Gate Opener on the Gate
The position of Post Bracket is very important. The following illustrations and tables are required to determine the
proper mounting position for the Post Bracket. The tables show the maximum opening angle of the gate for a given
A and B. For example, if A is 15cm and B is 20cm, the maximum opening angle of the gate is 110°. Pull-to-Open
Installation — Gate in Closed position (Moving-Rod is extended).
Note: for best performance we always recommended attaching the arm in the centre of the gate.
Please Note: Each swing arm contains an internal thread that may separate if over extended. If overextended
“Click” may be heard, to re-connect push and screw the sliding arm Clockwise until the arm begins to retract by
hand.
Tabla de contenidos
Otros manuales de Abridor de puerta de Richmond
Richmond
Richmond GTR064 Manual de usuario
Richmond
Richmond GTR500 Manual de usuario
Richmond
Richmond GTR058 Manual de usuario
Richmond
Richmond GTR211 Manual de usuario
Richmond
Richmond GTR502 Manual de usuario
Richmond
Richmond GTR181 Manual de usuario
Richmond
Richmond GTR058 Manual de usuario
Richmond
Richmond GTR058 Manual de usuario
Richmond
Richmond GTR156 Manual de usuario
Richmond
Richmond GTR062 Manual de usuario
