Rheem W2W Series Documento técnico

This water heater must be installed and serviced by an qualified person.

Please leave this guide with a responsible officer.

Owners Guide

and

Installation Instructions

Commercial Water to Water

Heat Pump Water Heater

WMKA21549

PATENTS

This water heater may be protected by one or more patents or registered designs.

® Registered trademark of Rheem Australia Pty Ltd.

™ Trademark of Rheem Australia Pty Ltd.

Notice to Victorian Customers from the

Victorian Plumbing Industry Commission.

This water heater must be installed by a licensed person as required by

the Victorian Building Act 1993.

Only a licensed person will give you a Compliance Certificate, showing that

the work complies with all the relevant standards. Only a licensed person will

have insurance protecting their workmanship for 6 years. Make sure you use

a licensed person to install this water heater and ask for your Compliance

Certificate.

CONTENTS

RESPONSIBLE OFFICER –We recommend you read pages 4 to 18.

The other pages are intended for the installer but may be of interest.

Contents.......................................................................................3

About Your Water Heater............................................................4

How Your Water Heater Works...................................................8

Regular Care ..............................................................................12

Water Supplies...........................................................................14

Save A Service Call ...................................................................16

Installation..................................................................................19

Heat Pump And Tank Assembly ..............................................31

Manifold Installations................................................................35

Connections –Plumbing ..........................................................38

Commissioning..........................................................................56

Draining The Water Heater .......................................................68

TROUBLE SHOOTING...............................................................68

Rheem Heat Pump Water Heater Warranty - Australia & New

Zealand Only -............................................................................70

ABOUT YOUR WATER HEATER

WATER HEATER APPLICATION

This water heater is designed for the purpose of heating potable water by

simultaneously reducing building chilling load. Its use in an application other than

this may shorten its life.

MODEL TYPE

Congratulations for choosing a Rheem®

commercial water to water (W2W) heat

pump water heater. The Rheem W2W

heat pump water heater is designed for

outdoor or indoor installation.

HOW HOT SHOULD THE WATER BE?

The heat pump (compressor, evaporator

and condenser) will operate until a water

temperature of up to 65C is reached.

To meet the requirements of the National

Plumbing Standard (AS/NZS3500.4) the

temperature of the stored water must not

be below 60C.

HOTTER WATER INCREASES THE

RISK OF SCALD INJURY

This water heater can deliver water at

temperatures which can cause scalding.

Check the water temperature before use,

such as when entering a shower or filling

a bath or basin, to ensure it is suitable for the application and will not cause scald

injury.

We recommend and it may also be required by regulations that an approved

temperature limiting device be fitted into the hot water pipe work to the bathroom

and ensuite when this water heater is installed. This will keep the water

temperature below 50C (55C in NZ) at the bathroom and ensuite. The risk of

scald injury will be reduced and still allow hotter water to the kitchen and laundry.

TEMPERATURE ADJUSTMENT

Set Point Quick Setting

Press ‘prg’ from the main display screen and the Set Point page will appear.

Cursor will be on the set temperature. Pressing the up and down keys will

adjust the setting in 0.1 increments. Hold down for rapid change. Press ’Enter’

to confirm change. Press ‘esc’ to return to the main display screen. Refer to

page 51 for more information.

minimum recommended

stored water temperature

maximum recommended

supply temperature to

bathrooms and ensuites

ABOUT YOUR WATER HEATER

WARNING

This water heater is only intended to be operated by persons who have the

experience or the knowledge and the capabilities to do so. This water heater is

not intended to be operated by persons with reduced physical, sensory or mental

capabilities i.e. the infirm, or by children. Children should be supervised to ensure

they do not interfere with the water heater.

This water heater uses 415V / 240 V AC electrical power for operation of the

control systems and other electrically operated components. The removal of the

access cover(s) will expose 415V / 240 V wiring. They must only be removed by

a qualified person.

SAFETY

This water heater is supplied with built in Rheem IQ Controller which controls low

and high pressure switches, low temperature cut off, temperature safety switch

and flow switch.

Additionally, the compressor is fitted with thermal overload protection, the

condenser heat exchanger is fitted with a pressure relief valve and the storage

tanks are supplied with a combination temperature pressure relief valve. These

devices must not be tampered with or removed. The water heater must not be

operated unless each of these devices is fitted and is in working order.

If the electrical supply conduit to the water heater is damaged, it must be

replaced by a qualified person in order to avoid a hazard. Phone your nearest

Rheem Service Department or Accredited Service Agent (or Service Centre in

NZ) to arrange for an inspection.

Warning: For continued safety of this water heater it must be installed,

operated and maintained in accordance with the Owner’s Guide and Installation

Instructions.

The Rheem warranty may not cover faults if relief valves or other safety

devices are tampered with or if the installation is not in accordance with

these instructions.

ABOUT YOUR WATER HEATER

TO TURN OFF THE WATER HEATER

Switch off the electrical supply at the isolating switch to the water heater

Close the cold side and hot side water isolation valve at the inlets to the water

heater.

TO TURN ON THE WATER HEATER

First, ensure the water is connected to storage tanks, the system is filled with

water and all valves between the tanks and the water heater are open

Open the cold side and hot side water isolation valve fully at the inlets to the

water heater.

Switch on the electrical supply at the isolating switch to the water heater.

Note: The water heater may not turn on immediately when it is first switched on,

if it is switched on within 20 minutes to 2 hours of it having been switched off at

the isolating switch, or the heat pump has just completed a heating cycle. The

water heater will wait until the conditions for start-up are favourable in order to

protect the compressor from damage. This may take up to 20 minutes to 2 hours.

The auxiliary booster will operate instead of the heat pump if the heat pump is in

fault or sufficient energy is not available from the chiller.

HOW DO I KNOW IF THE WATER HEATER IS INSTALLED CORRECTLY?

Installation requirements are shown on page 19. The water heater must be

installed:

by a qualified person, and

in accordance with the installation instructions, and

in compliance with Standards AS/NZS 3500.4, AS/NZS 3000 and all local

codes and regulatory authority requirements.

In New Zealand, the installation must also conform with Clause G12 of the New

Zealand Building Code.

DOES THE WATER CHEMISTRY AFFECT THE WATER HEATER?

This advice relates to the cold water side and hot water side of the heat

pump water heater.

The water heater is suitable for most public water supplies, however some

water chemistries may have detrimental effects on the water heater, its

components and fittings. Refer to “Water Supplies” on page 14. If you are

not sure, have your water chemistry checked against the conditions described

on pages 14 to 15.

ABOUT YOUR WATER HEATER

HOW LONG WILL THE WATER HEATER LAST?

Your water heater is supported by a manufacturer’s warranty (refer to page 72).

There are a number of factors that will affect the length of service the water

heater will provide. These include but are not limited to the water chemistry, the

water pressure, temperature (inlets and outlets) and the water usage pattern.

Precautions

Where damage to property can occur in the event of the water heater leaking,

the water heater must be installed in a safe tray or be suitably bunded.

Construction, installation and draining of a safe tray must comply with AS/NZS

3500.4 and all local codes and regulatory authority requirements.

The water heater must be maintained in accordance with the Owner’s Guide and

Installation Instructions. Refer to “Regular Care” on page 12.

If this water heater is to be used where an uninterrupted hot water supply is

necessary for your application, or business you should ensure that you have

back up redundancy within the hot water system design. This should ensure the

continuity of hot water supply in the event that this water heater were to become

inoperable for any reason. We recommend you seek advice from your plumber

or specifier about your needs and building back up redundancy into your hot

water supply system.

ENVIRONMENT

At the end of the service life of the heat pump water heater and prior to the water

heater being disposed of, a person qualified to work with refrigerants must

recover the refrigerant from within the sealed system. The refrigerant must not

be vented to atmosphere. Phone your nearest Rheem Service Department or

Accredited Service Agent (or Service Centre in NZ) to arrange for an inspection.

HOW YOUR WATER HEATER WORKS

The Rheem commercial water to water heat pump is an instantaneous type and

does not have an integral storage cylinder. The unit is designed to be installed

indoors or outdoors. The water heater’s evaporator absorbs heat from the

returning chilled water circuit or condenser loop and transfers this heat into the

potable water. A circulator transfers

the heated water to a bank of storage

tanks. By taking heat from the chilled

water circuit, the heat pump reduces

load on chiller as colder water returns

to the building chiller circuit. The heat

pump produces a sound level of up to

59 dBA (measured at 3 metres) when

it is operating.

When hot water is drawn off and cold water enters the storage tanks, a remote

thermostat activates the compressor and circulating pumps of the water heater.

The chiller return water (building heat) is drawn in through the cold side inlet and

then through the evaporator (single wall heat exchanger), where heat is

transferred to a refrigerant fluid. The fluid is compressed and passes to the

condenser (double wall heat exchanger) where heat is transferred into the

potable water. The pump circulates water from the bottom of the storage tanks

through the heat exchanger and the heated water is circulated back into the

storage tanks. This process continues until the water in the storage tanks

reaches the set temperature.

The heat pump is designed to operate most efficiently at cold side temperatures

between a minimum of 12C and maximum of 35°C. Operation with higher cold

side inlet temperature is possible, however must be engineered in consultation

with Rheem. The efficiency of the water heater is relative to the building chilled

water circuit temperature and the incoming hot side (potable) water temperature.

Automatic safety controls are fitted to the water heater to provide safe and

efficient operation.

FREEZE PROTECTION

Ice may begin to form in the evaporator when the cold side outlet temperature

falls below 4°C or the flow rate of cold side water is excessively low or the pump

on the cold side fails, and this may damage the evaporator heat exchanger.

HOW YOUR WATER HEATER WORKS

To prevent this damage, the pumps for

both sides of the water heater are sized

and supplied by Rheem and the heat

pump is supplied with a flow switch

sensor and a low temperature cut out

switch. The heat pump will terminate its

operation if poor flow rate is sensed or

the cold side outlet temperature or hot

side outlet temperature falls below

5°C.

AUXILIARY BOOST OPERATION

There are two types of auxiliary boost operation, which operate as follows:

ANTIFREEZE AUXILIARY BOOST OPERATION

When freeze protection activates, the heat pump will cease operating. It is then

possible to activate auxiliary heating mode.

In auxiliary heating mode the controller deactivates the heat pump and switches

to an auxiliary gas or electric water heater, if installed and activated in the menu.

A pump circulates water from the storage tanks through the auxiliary water heater

until the set temperature is reached.

When the cold side outlet temperature and hot side outlet temperature rises to

10°C, the auxiliary heating mode is deactivated and the heat pump starts

operating again.

For installations using multiple heat pumps in a master/slave configuration,

activation of antifreeze auxiliary boost operation on any heat pump activates the

auxiliary boost on all LAN connected heat pumps.

BACKUP AUXILIARY BOOST OPERATION

If the heat pump is in fault mode, the controller switches to an auxiliary gas or

electric water heater, if installed and activated in the menu. A pump circulates

water from the storage tanks through the auxiliary water heater until the set

temperature is reached.

HOW YOUR WATER HEATER WORKS

For multiple heat pump (Master/Slave) configuration, the auxiliary booster will

operate instead of the heat pumps if fifty percent (50%) or more heat pumps are

in fault.

For installations using multiple heat pumps in a master/slave configuration;

activation of backup auxiliary boost operation on any heat pump activates the

auxiliary boost on all LAN connected heat pumps.

The auxiliary boost should be set to 60°C.

The auxiliary boost will remain active until the water heater fault is cleared.

Warning: Rheem will not be responsible for higher utility bills due to

excessive use of auxiliary boost heater. It is the customers’ responsibly

to monitor the system regularly for its correct operation. Rheem

recommends monitoring via BMS (modules supplied separately).

MAINS PRESSURE

The water heater is designed to operate at mains pressure by connecting directly

to the mains water supply. If the mains supply pressure in your area exceeds

that shown on page 21, a pressure limiting valve must be fitted.

THERMAL CUT OUT

The refrigeration circuit is protected by thermal sensors. These will activate a

thermal cut out in the event of excessive heat in the refrigeration system.

If the thermal cut out has activated, the heat pump will not operate for a period

of 20 minutes to 2 hours. The water heater will make two more attempts to start

up. If the thermal cut out is tripped again after the third attempt, the system will

enter lock out and the alarm contacts will close. If connected to a BMS, this will

alert the user that the unit is not operating.

The lockout condition can be manually reset by switching the power to the water

heater off and then on.

CONTROL FUNCTIONALITY

A timer can be set through the heat pump control panel to limit the hours of

operation of the water heater (e.g. to reduce noise at night).

The operation of the heat pump can also be controlled by setting up tariff option

on the control panel to manage operating costs.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de agua de Rheem

Rheem

Rheem GHE119-500 Manual de usuario

Rheem

Rheem STELLAR 850 Series Documento técnico

Rheem

Rheem CRTGH-95X Series Manual de usuario

Rheem

Rheem 862 27 Series Instrucciones de funcionamiento

Rheem

Rheem Gas Domestic Indoor Water Heater Manual de instrucciones

Rheem

Rheem 82VP30 Manual de usuario

Rheem

Rheem 86VP6S Guía de instalación

Rheem

Rheem Eclipse 6C318500A Documento técnico

Rheem

Rheem Multipak MPE02 Documento técnico

Rheem

Rheem AP16697 Manual de usuario

Rheem

Rheem RUUD AdvantagePlus Instrucciones de funcionamiento

Rheem

Rheem AdvantagePlus HE119-130LP Manual de usuario

Rheem

Rheem Raypak B-195 Manual de usuario

Rheem

Rheem RUUD High-Power Commercial Water Heater Manual de usuario

Rheem

Rheem Gas Domestic Indoor Water Heater Manual de instrucciones

Rheem

Rheem 9 Kw Thru 36 Kw Manual de usuario

Rheem

Rheem Raypak 408A Manual de usuario

Rheem

Rheem Guardian PowerVent Manual de usuario

Rheem

Rheem 120 Volt Manual de usuario

Rheem

Rheem RUTG 64DV Manual de programación

Rheem

Rheem RTGH-RH11DV Manual de usuario

Rheem

Rheem RETEX-04T Manual de usuario

Rheem

Rheem HE45-160 Manual de usuario

Rheem

Rheem 3805 Series Documento técnico

Manuales populares de Calentador de agua de otras marcas

Kenmore

Kenmore 153.582400 Manual de usuario

Applimo

Applimo Edel AIR Manual de usuario

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manual de usuario

clage

clage E-Mini Series Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-180 Manual de usuario

Bradford White

Bradford White EF Series Manual de usuario

Eccotemp

Eccotemp 40-H Manual de usuario

Dimplex

Dimplex ECSd125-580 Guía

Dux

Dux 32FCR6N Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guía de solución de problemas

Noritz

Noritz N-132M Manual de instrucciones

TESY

TESY GCV7/4S 10047 Hoja de especificaciones

A.O. Smith

A.O. Smith Gphe 50 Manual de usuario

Koryo

Koryo KWHZF15Y Manual de usuario

Pentair

Pentair PSC-14-4-02 Manual de usuario

GE 40M06AAG Instrucciones de montaje

Thermor

Thermor AEROMAX SPLIT 2 Manual de usuario

American Hometec

American Hometec AHQ-B03X Manual de usuario