Rheem RPH Series Manual de usuario

RPH SERIES SWIMMING POOL HEAT PUMP

USER MANUAL

Heat Pump & Installation Information

Date of installation:

Model Nº:

Serial Nº:

Installed by:

Purchased from:

43 Marigold Street,

Revesby NSW 2212

ABN: 28 062 383 224

ACN: 062 383 224

Rheem Thermal Systems: 1300 132 950

Email:sales@rheemthermal.com.au

www.rheemthermal.com.au

PATENTS

This heat pump may be protected by one or more patents or registered designs.

® Registered trademark of RheemAustralia Pty Ltd.

™Trademark of Rheem Australia Pty Ltd.

Warning: Upon completion of the installation and commissioning of the heat pump, leave this guide with

the premises householder or responsible officer.

DO NOT leave this guide inside of the cover of the heat

pump, as it may interfere with the safe operation of the heat pump or ignite when the heat pump is turned on.

 
Table of contents 
A. Foreword 1 
B. Safety Precautions 1 
1. Warning 1 
1. Attention 2 
2. Safety 3 
3. Service 3 
C. About Your Heat Pump 4 
1. Transportation 4 
2. Accessories 4 
3. Features 5 
4. Operating condition and range 5 
5. Introduction of different modes 5 
6. Technical parameter 6 
7. Dimension 7 
D. Installation Guidance 8 
1. Installation reminder 8 
2. Wiring 10 
3. Electric wiring diagram 11 
4. References for protecting devices and cable specification 11 
E. Operation Guide 12 
1. Key functions 12 
F. Testing 15 
1. Inspect theheat pump before use 15 
2. Leakage detection notice and method 15 
3. Trial & Start Up 15 
G. Maintenance 16 
H. Trouble Shooting for Common Faults 17 
I. Hard Wired - Methods of Water Pump Control Connections 19 
J. Water Pump connection using the Rheem IQ Link –Pump Controllers 22 
K. Wi-Fi Connection Instructions 27 
L. RHEEM THERMAL WARRANTY –RPH SERIES POOL HEAT PUMPS 33 
 

A. Foreword

Thank you for choosing our RheemThermalinverter pool heat pump, which is designed for easeof

operation,quietness and efficiency. The low electrical use of your new heater minimises greenhouse

impact, providing a very green solution to pool heating.

B. Safety Precautions

Your heat pump is supplied as a package unit, being a closed refrigeration system,

connected directly to your pool either via the pool’s filtration or a standalone heating circuit

and suitable for outdoor installation only. This Manual includes important safety messages

please always read and obey all safety messages.

1. Warning

The WARNING sign denotes a hazard. It calls attention to a procedure,

practice, or the like, which, ifnot correctly performed oradhered to, could result inpersonal injury or injury

to a third party. These signs are rare but are extremely important.

a. Keep the heat pump away from a fire source.

b. The heat pump is suitable for outdoor installation only.

c. Repairs and disposal must be carried out by trained service personnel

d. Vacuumise all R32 gas completely before welding pipes. Welding can only

be carried out by professional personnel in a service center.

1. Attention

a. The specific instructions below related to the safe operation of the heat pump are set out below in accordance

with AS/NZS60335-1 and AS/NZS60335-2-40.

b. Installation requirements are detailed in the Installation Guidance section of this Manual.

c. The heat pump must be installed by 1. A qualified person, 2. In accordance with the installation instructions and

3. In compliance with Standards AS/NZS 3000, AS/NZS 3500.4 as applicable under local regulations and all

local codes and regulatory authority requirements.

d. In New Zealand, the installation must also conform with NZS 5261, as applicable under local regulations, and

the NZ Building Code.

e. The heat pump is supplied as a package unit, ready for immediate operation after installation with the provision

ofpowersupplyanddirectconnectionto your swimmingpool via PVC pipingas outlined in the hydraulic sections

of this Manual.

f. It is suitable for outdoor installation only and clearance guidelines are outlined in this Manual.

g. Connection to water mains is not intended.

h. For electrical connection, the selection of type and rating of fuses should be in accordance with the Installation

Guidance Section of this Manual.

i. The heat pump is a closed refrigeration system using the low GWP Refrigerant R32. As such, compliance with

national gas regulations shall be observed.

j. Do not pierce or burn.

k. Be aware that refrigerants may not contain an odour.

l. Do not use means to accelerate the defrosting process or to clean, other than those recommended by the

manufacturer.

m. The heat pump should be located to prevent the risk of mechanical damage from external sources.

n. If a repair is required, please contact the nearest after-sales service center. The repair process must be strictly

in accordance with manual. All repair practice by non-professional is prohibited.

o. Any person who is involved with working on or breaking into a refrigerant circuit should hold a current valid

certificate from an industry-accredited assessment authority, which authorises their competence to handle

refrigerants safely in accordance with an industry recognised assessment specification. Servicing shall only

be performed as recommended by the equipment manufacturer. Maintenance and repair requiring the

assistance of other skilled personnel shall be carried out under the supervision of the person competent in the

use of flammable refrigerants.

p. A leakage test must be performed after installation.

q. Please don’t stack substances, which will block air flow near inlet or outlet area, otherwise the efficiency of the

heat pump will be reduced or even stopped.

r. Don’t use or stock combustible gas or liquid such as thinners, paint and fuel in the vicinity of the heat pump to

avoid the risk of ignition.

s. In order to optimise the heating effect, please install heat preservation insulation on pipes between swimming

pool and the heat pump, and please use a recommended cover on the swimming pool.

t. Connecting pipes of the swimming pool and the heat pump should be ≤10m.

2. Safety

a. This heat pump is only intended to be operated by persons who have the experience or knowledge and the

capabilities to do so.

b. This heat pump is not intended to be operated by persons with reduced physical, sensory or mental

capabilities i.e. the infirm, or by children. Children should be supervised to ensure they do not interfere with or

play with or at the heat pump.

c. If electrical supply conduit to the heat pump is damaged, it must be replaced by a qualified person in order to

avoid a hazard. Phone Rheem or the nearest Accredited Service Agent to arrange for an inspection.

d. Please keep the main power supply switch far away from the children.

e. If power supply is disrupted during operation, the heat pump will start again when power is restored.

f. Please switch off the main power supply in lightning and storm weather to prevent from machine damage that

caused by lightning.

g. Installation and any repairing should be conducted in the area with good ventilation. The ignition source is

prohibited during the operation.

h. Safety inspection must be carried before the maintenance or repair for heat pumps with R32 gas in

order to minimize the risk.

i. If R32 gas leaks during theinstallation process, all operations must be stopped immediately and call the service

center.

3. Service

a. This heat pump must be maintained and serviced in accordance with the Maintenance Guidelines Section of

this Manual.

b. For peak performance, it is suggested that the heat pump is serviced by your nearest Rheem Thermal

Service Department or Accredited Service Agent every four months for commercial installations or annually

for residential installations.

c. Warning: Servicing of a heat pump must only be carried out by a refrigeration mechanic.

C. About Your Heat Pump

1. Transportation

a. Always keep upright

b. Do not lift the unit by the water

unions (Otherwise the titanium

heat exchanger inside the heat

pump may be damaged)

2. Accessories

Connection for the condensate drainage kit:

Water Connection Unions

3. Features

a. Mitsubishi - DC Twin-rotary inverter compressor

b. DC Brushless fan motor

c. EEV Technology

d. Reverse cycle defrost

e. High efficiency twisted titanium heat exchanger

f. Sensitive and accurate temp control and water temp display

g. High pressure and low-pressure protection

h. Full protection on electrical system

4. Operating condition and range

The heat pump RPH009-1A, RPH013-1A, RPH016-1A, RPH021-1A, RPH024-1A can work between ambient

air temperatures of -5°C～43°C and the RPH028-1A, RPH028-3A can work between ambient air temperatures

of -10°C～43°C and their ideal operation range is between 15°C ~ 25°C.

5. Introduction of different modes

a. The heat pump has two modes: Boost and Silence.

b. They have different strengths under different conditions.

Mode

Modes

Strength

Boost mode

Heating capacity: 20% to 100%

Intelligent optimisation

Fast heating

Silence mode

Heating capacity: 20% to 80%

Sound level: 3dB (A) Lower than Boost mode

6. Technical parameter

Model

RPH009-1A

RPH013-1A

RPH016-1A

RPH021-1A

RPH024-1A

RPH028-1A

RPH028-3A

PERFORMANCE CONDITION: Air 27°C/ Water 27°C/ Humid. 80%

Heating

capacity (kW)

8.6

15.5

23.5

27.8

COP Range

14~6.5

14~6.4

15~6.5

14.5~6.4

15.8~7.2

15.6~7.1

Average COP

at 50% Speed

9.0

9.5

9.6

9.3

9.6

11.0

10.7

PERFORMANCE CONDITION: Air 15°C/ Water 26°C/ Humid. 70%

Heating

capacity (kW)

6.4

9.0

10.9

14.5

16.1

18.8

COP Range

6.8~4.5

7~4.4

7~4.5

7~4.6

7.2~4.5

7.8~4.9

Average COP

at 50% Speed

6.2

6.3

6.2

6.3

6.5

6.4

TECHNICAL SPECIFICATIONS

Advised pool

volume (m3) *

20~50

30~60

40~75

50~90

60~110

60~120

Operating air

temperature

(°C)

-5°C ~43°C

-10°C ~43°C

Power supply

240V 1Ph

415V 3Ph

Rated input

power (kW)

0.21~1.42

0.31~2.10

0.37~2.42

0.47~3.20

0.54~3.60

0.50~3.84

0.5~3.84

Rated input

current (A)

0.93~6.20

1.34~8.90

1.60~10.60

2.06~13.70

2.34~15.60

2.17~16.70

0.72~5.56

Recommended

circuit breaker

size (A)

Sound level at

10m dB (A)

19.0~28.4

22.2~30.8

21.2~34.4

23.4~34.1

21.8~36.0

21.5~32.9

Refrigerant

charge (kgs)

0.5

0.75

0.8

1.0

1.2

2.0

Advised water

flow (L/sec)

0.5~1.2

1.2~1.7

1.7~2.3

2.0~2.8

2.8~3.4

Water

Connections

mm)

48.3

Remarks:

The heat pump RPH009-1A, RPH013-1A, RPH016-1A, RPH021-1A, RPH024-1A are all able to perform normally within

air temp -5°C～+43°C and the RPH028-1A, RPH028-3A can perform normally within air temp -10°C~+43°C. Efficiency

cannotbeguaranteedoutofthisrange. Please takeinto considerationthat the pool heat pump performance and parameters

are different under various conditions.

Related parameters are subject to adjustment periodically for technical improvement without further notice. For further

details please refer to the nameplate on the side of the unit.

7. Dimension

※The above product data is subject to change without notice.

Note: The product pictures and dimensions above are specification diagrams for use by technician’s

installers and for layout reference only.

Size (mm)

Model

RPH009-1A

410

645

387

430

890

250

657

RPH013-1A

410

645

387

430

890

290

657

RPH016-1A

410

645

387

430

890

280

657

RPH021-1A

410

710

387

430

1060

390

657

RPH024-1A

410

710

387

430

1060

390

757

Size(mm)

Model

RPH028-1A

410

710

390

430

1060

640

957

RPH028-3A

410

710

390

430

1060

640

957

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de Rheem

Rheem

Rheem MPi Series Manual de usuario

Rheem

Rheem PNL-*AZ Series Manual de usuario

Rheem

Rheem RP1336AC1NA Manual de usuario

Rheem

Rheem MPs Series Manual de usuario

Rheem

Rheem RGEA16 Manual de usuario

Rheem

Rheem RJNA Series Manual de usuario

Rheem

Rheem RJNL-A036CK Manual de usuario

Rheem

Rheem RQMP 14 Series Manual de usuario

Rheem

Rheem 953060DP Documento técnico

Rheem

Rheem AWW023SK JQ-1 Series Manual

Rheem

Rheem RKNA SERIES Manual de usuario

Rheem

Rheem RP13 Manual de usuario

Rheem

Rheem 325 II Series Instrucciones de funcionamiento

Rheem

Rheem Raypak Hi Delta H Series Manual

Rheem

Rheem RA13 Series Manual de usuario

Rheem

Rheem RHPD Series Manual de usuario

Rheem

Rheem RRPL-B Manual de usuario

Rheem

Rheem Raypak Hi Delta P902C Manual

Rheem

Rheem RPVS Series Guía

Rheem

Rheem 15 SEER Series Manual de usuario

Rheem

Rheem P17 Series Manual de usuario

Rheem

Rheem RQPM 15/16 Seer Series Manual de usuario

Rheem

Rheem Seven Manual de usuario

Rheem

Rheem ECONET RP2024BJVCA Manual de usuario

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario