Revolabs Fusion Manual de usuario

Rev 1.1

Revolabs Fusion™ Wireless

Microphone System

User’s Guide

Page 2

Table of Contents

Using the Fusion IR Remote Control 4

Using the Fusion Charger Base 6

Using the Revolabs Solo™ Microphones 8

Wearable Microphone 8

Tabletop Microphone 10

XLR Adapter for Dynamic Microphone 12

Indicator Lights 14

Revolabs Fusion™

Page 3

Great audio, wireless mobility, and simple to install!

Simply plug the cable into the AV system or phone system and it

works. No software configuration is necessary. Even the Fusion

box is designed to be easy to use– vertically or horizontally. No

equipment rack needed. Just set the Fusion system on the

credenza.

Video Conferencing

Revolabs Fusion Wireless Microphone Solution is compatible with

all of the major video-conferencing solutions, including Lifesize,

Polycom, Sony, and Tandberg. It includes a remote control .

Decide on where you want to put the Fusion system, whether you

want to place it vertically or horizontally, plug in the cables and you

are ready to have great wireless audio in any conference room.

Audio Conferencing

Plug the Fusion Wireless Microphone Solution into an analog

telephone jack and you are on your way to great wireless

teleconference calls. There is a remote control dialer to dial the

conference phone number . You may connect to powered

speakers, connect to existing speaker system or connect to a new

room speaker system to hear the call. Decide on where you want to

put the Fusion system, whether you want it vertical or horizontal,

plug in the cables and you are ready to have great wireless audio in

any conference room.

Flexible

The Fusion System supports any combination of Solo Wireless

Microphones- Wearable, Tabletop, or XLR adapter for s handheld

microphone. Choose the right microphone for your meeting

dynamics.

Rechargeable

Revolabs Wireless Microphones have a rechargeable battery that

provides eight hours of talk time after each full charge. Revolabs

Wireless Microphones recharge to 85% capacity in approximately

45 minutes.

Secure

All of Revolabs Wireless Microphones use 128-bit authentication,

so that no one can listen in.

Using the Fusion™ IR Remote Control

Page 4

Flash:phone function

Redial: phone function

Vol +: increases volume

Call: dial-tone

End: hang-up

Vol -: decreases volume

Phone Dial Pad

User’s Guide

Dial a Call

To make a call, push “Call” to get dial tone, then dial the phone number on the

Phone Dial Pad.

Answer a call

To answer a call when the system is ringing, push “Call",

Mute and Unmute a Call Using Remote Control Mute Button

To mute all of the microphones, press the red MUTE button; all microphones

will flash red and no individual microphone can be unmuted until the remote

MUTE button is pressed again. To unmute, press it again. All microphones will

return to their prior state.

Revolabs Fusion™

NOTE: In the default setting, each Solo microphone will mute only itself when

its MUTE button on the microphone is pressed. To mute all of the

microphones, press the red MUTE button on the Remote Control; all

microphones will flash red and no individual microphone can be unmuted until

the remote MUTE button is pressed again. All microphones will return to their

prior state.

However, if the tabletop microphone master mute has been enabled (Refer to

Set-Up Guide), the mute will work as follows: in addition to the Remote

Control MUTE button muting all of the microphones, the Solo Tabletop

microphone MUTE button will also act as a master mute and mute all active

microphones. Pressing any Tabletop microphone MUTE button or the Remote

Control MUTE button will unmute all tabletop microphones. All wearable and

handheld adapter microphones in use will return to their prior state.

End a Call

To end a call, the user must push “End", even if the other callers have hung up.

Redial a Call

To redial a the last phone number, push “Redial”.

Adjust Volume

To increase and decrease the volume , use the Vol + and Vol- buttons.

Flash Button

“Flash” works according to your phone system.

Page 5

User’s Guide

Using the Fusion™ Charger Base

When microphones are not in use, they should be properly inserted into the

Charger Base. It is important to ensure that the system microphones are

inserted fully in the base so that charging will occur.

1. LED indicator — power / mute status indicator

2. Charger Bay — charges up to 8 Microphones.

3. Power Cord Receptacle— power supply input (on rear)

The Charger Base requires 5VDC power, provided by the AC Adapter. Plug the

supplied AC wall adapter into an appropriate power outlet 110-240 AC, 50-

60Hz. The power LED on the Charger Base will illuminate.

Charging the Microphone Batteries

First-time use — before using the wireless microphone the first time, charge

the batteries in the microphones for eight hours (or overnight) in the Charger

Base.

Page 6

Page 7

Recharging — when the YELLOW LED starts to flash intermittently on the

microphone the battery has 30 minutes of charge remaining. To charge the

batteries place microphones into the Revolabs Solo™ Executive Charger Base

and the mic LED's will display a 5 blink "self test". During charging, the LED

indicator will be RED when mics are discharged and turn GREEN when charged.

The microphones are muted while in the Charger Base. In normal use, batteries

should fully charge in about 2 hours, and can be “quick-charged” to 85% capacity

in 45 minutes. Over time (years), batteries gradually wear down and require

longer charging times. This is normal. Always return microphones to the

Charger Base when not in use.

The batteries of microphones left in the Charger Base remain solid GREEN.

Important: The Lithium Polymer rechargeable batteries that power the microphones

are not user serviceable. Please contact Revolabs (www.revolabs.com) or your AV

service provider for replacement instructions and to assure the proper disposal method

is used.

Warning: Never dispose of batteries in a fire because they may explode.

NOTE: A fully charged battery provides approximately 8

hours of talk time

Revolabs Fusion™

Page 7

Using Revolabs Solo™ Microphones and

Microphone Adapters

Use any Solo Microphone microphones with your Revolabs Solo™ Executive

system:

• Revolabs Solo™ Wearable Wireless Microphone

• Solo Tabletop Wireless Boundary Microphone

• Solo Universal Wireless Adapter for Handheld Microphone

Using Revolabs Solo™ Wearable Wireless Microphone

The Revolabs Solo™ Wearable Microphones, shown in the following figure, are

paired to the Base Station and can be worn on the user’s shirt pocket, lapel or

on a lanyard.

1. Microphone port — direct port toward mouth for best audio pickup.

2. Noise cancelling port — do not block opening.

3. Mute Button — press to mute, un-mute and pair microphone.

4. Pocket clip — also used to attach microphone to lanyard.

5. LED display — visual status for mute, un-mute, and pairing.

6. Earpiece jack — accepts the 2.5mm plug for the earpiece

7. Charging port — charges in Charger Base.

Page 8

User’s Guide

Page 9

Revolabs Solo™ Wearable Microphones turn on and mute automatically when

removed from Charger Base, to reduce noise while being attached. The

microphone has a clip on the back which allows the microphone to be easily

attached onto a shirt pocket, blouse, lapel or lanyard.

To use the Wearable Microphone:

• Remove the microphone from the Charger Base.

• Attach the microphone to clothing or to a lanyard close to the mouth,

within 6 - 12 inches (15 – 30cm) is recommended. Make sure microphone

is attached securely with the microphone port pointed up toward mouth.

• With the microphone in the wearing position, un-mute the microphone by

pressing and releasing the Mute button (confirm by viewing flashing GREEN

LED). If the volume is too low, move the microphone closer to the mouth.

• To turn microphones off, return the microphone unit to the Charger Base

or press and hold the Mute button for ~10 seconds until the LED turns

solid RED and release button.

• If the microphones are moved out of range of the Base Station (~100 feet

or 30 meters) the connection will be dropped (LED flashes all colors) and

the microphone will mute.

• After 15 seconds the microphone will beep 5 times, and will continue

beeping every 30 seconds to remind the user to return the microphone to

the conference room. If the microphone is moved back into range within

15 minutes the connection will automatically be re-established to its

original state, and the beeping will cease. If not, the microphone will turn

off.

Muting Microphones

In the default setting, each Solo microphone will mute only itself when its MUTE

button on the microphone is pressed. To mute all of the microphones, press

the red MUTE button on the Remote Control; all microphones will flash red

and no individual microphone can be unmuted until the remote MUTE button is

pressed again. All microphones will return to their prior state.

However, if the tabletop microphone master mute has been enabled (Refer to

Set-Up Guide), the mute will work as follows: in addition to the Remote

Control MUTE button muting all of the microphones, the Solo Tabletop

microphone MUTE button will also act as a master mute and mute all active

microphones. Pressing any Tabletop microphone MUTE button or the Remote

Control MUTE button will unmute all tabletop microphones. All wearable and

handheld adapter microphones in use will return to their prior state.

Revolabs Fusion™

Using Solo Tabletop Wireless Boundary Microphones

The Solo Tabletop Wireless Boundary Microphones enable multiple conference

attendees to use a single microphone.

The Tabletop Wireless Microphone, shown on the following page, is designed to

provide optimum coverage when placed on a conference room table.

1. Mute button — press to mute, un-mute and pair microphone

2. LED display — visual status for mute, un-mute, and pairing

3. Integral grille — protects internal parts (non-removable)

4. Audio jack — accepts a 2.5mm plug

5. Charging port — docks to Charger Base

6. Rubber feet — non-slip, vibration absorbing pads

To use the Revolabs Solo™ Tabletop Microphone:

• Remove the microphone from the Charger Base to turn on and

automatically mute the microphone (indicated by a flashing RED LED)

during placement on the conference table.

• Tabletop microphones should be centered on the table with the integral

grill pointed toward the users (uni-directional), or centrally located

between users (Omni-directional), from 2 to 5 feet (.75 to 1.75m) away. It

is always better to be as close to the person speaking as possible, but avoid

placing the microphone where it might be blocked by equipment or

meeting paperwork. Also do not place microphones too close to an audio

or video conference speaker to avoid echoes.

Page 10

User’s Guide

Otros manuales para Fusion

Tabla de contenidos

Otros manuales de Sistema de micrófono de Revolabs

Revolabs

Revolabs Executive Elite 03-ELITEEXEC8-AU Instrucciones de funcionamiento

Revolabs

Revolabs Executive Elite 2 Instrucciones de funcionamiento

Revolabs

Revolabs 02-HDSGL Manual de usuario

Revolabs

Revolabs xTag 02-DSKSYS-D Manual del propietario

Revolabs

Revolabs 03-HDEXEC4EU Instrucciones de funcionamiento

Revolabs

Revolabs Fusion Manual de usuario

Revolabs

Revolabs 01-HDEXEC4-NM Instrucciones de funcionamiento

Revolabs

Revolabs VSX7000s Manual de usuario

Revolabs

Revolabs xTag Manual de instrucciones

Revolabs

Revolabs Single Channel System Manual de usuario

Revolabs

Revolabs xTag 02-DSKSYS-D Manual del propietario

Revolabs

Revolabs 01-HDVENU Manual de usuario

Revolabs

Revolabs Fusion Manual de usuario

Revolabs

Revolabs 02-HDSGL Manual de usuario

Revolabs

Revolabs 01-4FUSIONEU-NM Manual de usuario

Revolabs

Revolabs Fusion Manual de usuario

Revolabs

Revolabs REVOLABS SOLO 02-DSKSYS Manual de usuario

Revolabs

Revolabs Executive Elite 01-ELITEEXEC8 Instrucciones de funcionamiento

Revolabs

Revolabs Fusion Instrucciones de instalación y funcionamiento

Revolabs

Revolabs SOLO EXECUTIVE 01-EXESYS Manual de usuario

Revolabs

Revolabs 01-HDEXEC-NM Instrucciones de funcionamiento

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Shure

Shure UA844 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario