Response CA2 Manual de usuario
LCD Screen for
Wireless/Wired CCTV Kits
CA2
Installation and Operating Instructions
These instructions should be retained in a safe place for future reference.
2
1INTRODUCTION 3
2KIT CONTENTS 5
3FEATURES 5
4INSTALLATION 6
4.1 Wireless Camera(s) Setup 6
4.2 Screen Installation and Setup 6
5OPERATION 8
5.1 Wired/Wireless Source Function 9
5.2 Wireless Camera(s) Function 9
5.2.1 Manual Function 9
5.2.2 Auto Function 9
5.2.3 Scan Function 9
5.2.4 Cam 1 to 3 Function 9
5.3 Volume Adjustment for
A/V Input Source(s) 10
5.4 General Screen Settings 10
6MAINTENANCE 11
7TROUBLESHOOTING 11
8ACCESSORIES IN
THE RANGE 12
9TECHNICAL SPECIFICATION 13
10 APPENDIX 14
Screen Mounting Guide 14
11 DISPOSAL – RECYCLING
INSTRUCTIONS 15
12 GUARANTEE AND
CUSTOMER HELPLINE 16
CONTENTS
Please read before you start:
Always use discretion when installing CCTV surveillance equipment especially
when there is perceived policy. Enquire regarding local regulations applicable
to the lawful installation of video recording/surveillance. Third party consent
may be required.
3
INTRODUCTION Section 1
The Response Colour LCD Screen allows surveillance of any vulnerable places or areas
you wish to monitor. It allows you to connect both wired and wireless cameras (operating
on the 2.4GHz transmission frequency). You can connect up to 2 wired cameras and up
to 3 wireless cameras for surveillance.
The screen can also be used to view video and hear audio output from devices such as
DVD players, camcorders, etc, using any of the the 2 wired inputs via the supplied adaptors.
IMPORTANT:
Other devices transmitting on the 2.4GHz frequency may be picked up by this monitor on
any wireless channel. If this is experienced investigate the cause of interference. Typical
examples of devices operating on this frequency around the home can include wireless
routers or cordless phones. Avoid placing the LCD screen near to any potential source of
RF interference, a microwave oven or a metal radiator.
For best transmission, avoid installations where there are very thick walls or major
obstructions between the wireless camera and LCD screen.
2.4GHz
Up to 3 Wireless Cameras
2.4GHz transmission frequency
LCD Screen
2 Wired Cameras
+
5 Cameras can be used with the LCD Screen
4
SAFETY AND INSTALLATION TIPS:
The screen is intended for internal use only.
The Remote Control is supplied fitted with a CR2025 Lithium coin cell battery. If it is
removed, do not place in your mouth as this could impair your health. Keep these cells
out of reach from young children as they are a choking hazard.
The battery should not be exposed to excessive heat as this could reduce the battery’s life.
Damage to the unit may occur if the battery is replaced incorrectly according to the polarity
of the battery terminals in the Remote. Replace only with the same or equivalent type.
Do not attempt to open the unit with the power adaptor plug connected to avoid any risk
of personal injury. When installing any wired/wireless CCTV camera(s), always follow the
manufacturer’s advice when using power tools and wear suitable protective equipment
(e.g. safety goggles) when drilling holes, etc. Before drilling holes through walls check for
hidden electricity cables and water pipes. The use of a cable/pipe detector is advisable.
When installing the camera(s), it is advisable to use cable conduit to protect any
video/power extension cables from being exposed externally and to prevent/reduce the
chances of the cables being tampered. After drilling any hole though an external wall for
a cable, ensure the hole is sealed up around the cable using a sealant to prevent drafts.
There are no user serviceable parts inside. Refer servicing to qualified service personnel.
5
FEATURES Section 3
●2.4GHz wireless technology to receive up to 3 wireless cameras
●2 x wired inputs for viewing the output from wired cameras and other devices
such as DVD players, camcorders, VCR’s, etc.
●7.0inch LCD for good quality picture display
●Remote control
●Manual switching between wired and wireless cameras
●Selectable screen ratio of 4:3 (standard), 16:9 (DVD movie) and extended 4:3
●Up/down reverse function when the screen is installed upside down
●Can be wall, table or ceiling mounted
●Dwelling function for automatically viewing each wireless camera at a time
(Note: this function is not available for wired cameras)
KIT CONTENTS Section 2
1x7”Colour LCD Screen
1xRemote Control (supplied fitted with a 3V CR2025 battery)
2xWired cameras adaptor leads
1xPower supply adaptor
1xMonitor fixing kit – wall plugs and screws
1xInstallation and operating manual
Tools Required:
(only for wall/ceiling mounting the screen)
Electric drill
6mm drill bit (use a masonry bit if mounting on concrete walls/ceilings)
6
INSTALLATION Section 4
4.1 Wireless Camera(s) Setup
This screen is compatible with wireless cameras operating on the 2.4GHz frequency. Do
not set multiple cameras on the same channel or interference will appear on the screen.
It is possible to link up to 3 wireless cameras; however you may need to adjust the
orientation of the screen depending on the reception of the viewing channel. If interference
is experience by any of the camera and the source of inference cannot be located, then
set this camera to any of the unused channels.
Note: the channel 4 setting on any wireless camera must not be selected as this screen
only operates with wireless cameras set to channels 1 to 3.
Refer to the installation and operating manual of your wireless camera for setting the channel.
4.2 Screen Installation and Setup
1. The screen can be placed on the table (flat horizontal surface), wall or upside
down mounted. If wall mounting, use the mounting guide in the Appendix section
of this instruction manual. Mark and drill two holes using a 6mm drill bit.
Use the fixing screws and plugs provided.
CAM 2CAM 1 SCANCAM 3 AUTO MANUAL
CAM 1 CAM 2 CAM 3 Scan Auto Manual
LCD SCREEN
LCD Screen
Power Suppl
y
Adaptor
Power Jack
(on back of base)
Infra-Red Receiver
for Remote Control
Earphone
Jack
DC IN 9V
7
2. To connect wired cameras or other devices such as a DVD player to this screen,
use the supplied wired cameras adaptor lead. Up to two units can be connected
to this monitor at the same time using the two adaptors supplied.
2.1 Plug the jack plug end(s) of the adaptor(s) into the AV IN ports.
2.2 Connect the RCA male plug end of the wired camera into the yellow plug
of the adaptor to view video only. If other devices such as a DVD player
are connected then use both the yellow and white plugs for video and
audio output.
3. The screen’s DIP switch is located on the bottom panel. These should be
adjusted to reflect the number of wireless camera channel(s) in use.
By default it will be supplied set to 1 meaning only one wireless camera
will link to it when powered up.
4. To use any earphones with this unit, plug the earphones into the socket provided
on the side.
REAR OF LCD SCREEN
A/V OUT
A/V IN 2
A/V IN 1
A/V OUT
A/V IN 2
A/V IN 1
DC IN 9V
Power Jack
Camera 1
in Use
1 2 3 1 2 3 1 2 3
Cameras
1 and 2
in Use
Cameras
1, 2 and 3
in Use
8
OPERATION Section 5
5. The output from the screen can be viewed on a larger screen using the optional
A/V OUT port. Use any of the supplied two adaptors leads with this kit. You will
need to source a suitable AV output adaptor with male type RCA plugs to
connect to the adaptors supplied.
LCD Screen Control Functions
1. Turn ON any wireless cameras if setup. Turn ON any wired camera(s) or
devices connected to the screen.
2. Plug the LCD screen’s power supply adaptor into the power jack on the rear of
the LCD base.
3. Remove the battery isolation tab located on the battery cover on the Remote
Control unit.
4. Turn on the LCD screen by pressing the POWER button at the top of the monitor.
By default, the monitor will automatically search for any active wireless cameras,
depending on the numbers of channels setup on the screen. It will display each
wireless camera at a time (4 seconds default) and repeat the cycle.
The screen can be set to operate in one of three modes: Scan, Auto or Manual.
The desired operating mode can be selected using the buttons on the front panel
or by using the supplied Remote Control.
CAM 2CAM 1 SCANCAM 3 AUTO MANUAL
Power Source Menu
-
Volume +
CAM 1 CAM 2 CAM 3 Scan Auto Manual
Power Source Menu Volume/Adjust
Mute
Manual
Auto
Scan
Up/Down
Mirror
CAM3
Source
CAM1
CAM2
Menu
Mute CAM 1
CAM 2
Manual
CAM 3
Auto Source
Menu
Scan
LCD SCREEN - FRONT
LCD SCREEN - TOP
REMOTE
CONTROL
Mirror
CAM 3
9
5.1 Wired/Wireless Source Function
Each time the ‘SOURCE’ button is pressed, the screen will change from wireless to wired.
If any wired cameras or devices are connected using the wired adaptors, then press this
button to view the required source.
5.2 Wireless Camera(s) Functions
5.2.1 Manual Function
To view a specific wireless camera, press the ‘MANUAL’ button until the required camera is
viewed. The screen will switch to a different camera each time the Manual button is pressed.
5.2.2 Auto Function
When the ‘AUTO’ button is pressed, the screen will return to cycle or dwell mode and
display each active wireless camera that has been set on the channel DIP switch located
on the screen. In this mode, there is also an optional built-in function for wireless cameras
with a built-in PIR motion detector. When the PIR detector senses motion, the screen’s
beeper will sound and display the image from that camera for a few seconds.
The preset display time for each camera is 4 seconds but is adjustable between 2-30
seconds. To change this dwell time, press and hold both the Auto and Manual buttons
simultaneously. The screen will beep depending on how long the buttons are pressed for.
After releasing them, the screen will ‘beep’ and the green LED on the AUTO button will flash
with each ‘beep’. The total number of beeps and flashes indicate the new dwell time.
5.2.3 Scan Function
(Optional function for PIR activated wireless cameras only)
When the ‘SCAN’ button is pressed, the whole system is placed in standby and the screen
will appear blank. However the screen continues to scan through each active PIR wireless
camera. If a camera senses motion, the screen’s alarm will sound and the image from
this camera will be displayed.
After a further 4 minutes, the system will return to standby again and continue scanning.
5.3.4 Cam 1to 3 Function
By pressing any of the 3 ‘CAM’ buttons corresponding to a PIR wireless camera, the PIR
function of a camera can be enabled or disabled. The LED on the button pressed will turn
green to indicate enabled. If pressed again, it will turn off to indicate it is disabled.
10
5.3 Volume Adjustment for A/V Input Source(s)
The sound level of the audio from the screen can be adjusted by pressing the ‘+’ or ‘
-
‘
button on the Volume/Adjust button.
5.4 General Screen Settings
Press the Menu button to cycle through the following settings:
Alarm volume - adjust by pressing the ‘+’ or ‘
-
‘ button on the Volume/Adjust button.
Contrast - adjust by pressing the ‘+’ or ‘
-
‘ button on the Volume/Adjust button.
Brightness - adjust by pressing the ‘+’ or ‘
-
‘ button on the Volume/Adjust button.
Colour - adjust by pressing the ‘+’ or ‘
-
‘ button on the Volume/Adjust button.
Tint - adjust by pressing the ‘+’ or ‘
-
‘ button on the Volume/Adjust button.
Updown - if the screen is mounted upside down, this function must be
enabled to view the picture correctly in this mounted position.
Mirror - this function is used for vehicle reversing Cameras. The screen
will act as a rear view mirror when this function is enabled.
Tabla de contenidos
