Replay XD 1080 Mini Manual de usuario
QUICK START GUIDE
Replay XD 1080 Mini Camera
(A) Power On/O,
(B) Record, Stop
(C) Removable Lens Cover
(D) Removable End Cap
(E) 15 Degree Markings
(F) Power On/O Blue LED
(G) Record On/O Red LED
(H) Horizontal Sight Line
(I) Vertical Sight Line
(J) microSDHC Slot up to 32GB
(K) Charging Green LED, No SD Card Red LED
(L) Video Mode: 1080p 30, 720p 60 (or Photo)
(M) Internal Mic/Audio Line-In Switch (Ext. Mic-In)
(N) Mini USB Port
(*) Master Reset ORIENTATION
C
H
I
DE
M
N
J
K
L
*
G F
A B
RECORDING
Press A to Power On/Power O. Press B to START/STOP Recording. You’re Done.
Power On (Standby & Mode Setting Selection): Hold down front button (A) for 2 sec. & release, the Replay
XD 1080 Mini will vibrate 3 times & illuminate the blue power LED.
Note: Camera will turn o after 5 seconds if no SD card is present. Camera will turn o after 5 minutes of no activity.
Start Recording: Hold down rear button (B) for 2 sec. & release, the Replay XD 1080 Mini will vibrate 3 times,
illuminate the red LED & automatically start recording or capturing.
Note:The red LED on the rear will blink when the memory card is not inserted properly. Make sure the memory card
is fully inserted with the gold contacts face-down unttil it clicks. Use only Replay XD approved SD cards.
Visit www.replayxd.com for SD card compatibility list.
Stop Recording: Hold down the rear button (B) for 4 sec. & release, the Replay XD 1080 Mini will vibrate 1 time to
notify you that it is saving the le.
Power O: Hold down the front button (A) for 4 sec. and release, the Replay XD 1080 Mini will vibrate 1 time &
power o.
Note:The power button will not function when recording. This is normal to prevent accidental powering o.
Clip File (Available in Advanced text File): While recording quickly press the rear button (B) and release, the Replay XD
1080 Mini will vibrate 1 time to notify you that it is clipping & saving the le, then automatically starts recording.This feature
allow you to start a new le without starting or stopping the recording.
G F
A B
MODES & SETTINGS
1080p Video Mode / Frames Per Second
1. Slide theVideo Mode switch (L) to change video resolution frames per second.
a. 1080p 30 FPS (Full HD)
b. 720p 60 FPS (Smooth HD), Photo Mode can be enabled in the AdvancedText File
Audio Option
1. Slide the INT./EXT. switch (M) to choose audio option.
a. Internal Mic (Default)
b. External Line-in, disables internal Mic
External Line-in is compatible with Replay XD 1080 Mini Audio Adapter or
Replay XD 1080 Mini HW Kit, available at www.replayxd.com
For Advanced Users and Setting Proles visit www.replayxd.com/replay-XD1080MINI-advanced/
REAR VIEW
M
L
1. Find the best mounting location for your Replay XD 1080 Mini and check your angles.
Rigid surfaces are ideal for the best video quality. Note: Youcanmakeatestrecording andcheck
iton your MacorPC.
2. Snap Replay XD 1080 Mini into u-shape camera holder and rotate 360º to desired rotation.
3. AttachVHB SnapTray adhesive mount to a clean smooth surface.
-Flat SnapTray’s are good for at smooth surfaces.
-Curved SnapTray’s are good for curved surfaces such as Helmets & Radius surfaces.
The 3MVHB adhesive is not recommended for textured surfaces.
4. Slide HeimLock mount into SnapTray until it is fully seated and clicks.
5. Adjust swivel 360º or tilt ~8º by releasing the heim cam lever and position Replay XD
1080 Mini in desired direction, then lock the cam lever. Make sure the cam lever is tight.
There is an adjustable tension wheel and phillips screw (*) to make sure you always have
a positive tight lock.You can tighten the screw clockwise in 1/4 turn increments to nd
the desired tension when the cam lever is locked.
HEIMLOCK MOUNT
See our full range of mounts at www.Replayxd.com
*
VHB SnapTray HeimLock Mount
Unlock
Lock
Tighten
Set screw
TiltSwivel
IMPORTANT
Use rubbing alcohol to clean
the mounting surface.Wipe
dry the surface. Apply your
VHB mount to surface. Press
and hold for sixty seconds to
allow adhesive to bond to
the surface. Bond strength
willincreasethrough time.
At room temperature,
wait for at least 24 hours
to achieve 90% bonding
strength, and 72 hours for
100%bonding strength.
1. Find the best mounting location for your Replay XD 1080 Mini and check your angles.
Rigid surfaces are ideal for the best video quality. Note: You can make a test recording and
check it on an iPad/Mac/PC.
2. Flip LowBoy mount upside down and carefully spread, insert Replay XD 1080 Mini
into holder with buttons passing through the cut-out.
3. With the Replay XD 1080 Mini centered in LowBoy mount, rotate 360º to desired
rotation.
4. Slide LowBoy mount into SnapTray until it is fully seated and clicks.The LowBoy mount has
rubber strips to hold your Replay XD 1080 Mini from rotating when seated, make sure your
rotation angle is ideal.You can make ne adjustments by sliding the LowBoy in/out of the
SnapTray.
5. Attach VHB SnapTray adhesive mount to a clean smooth surface.
The 3M VHB adhesive is not recommended for textured surfaces.
LOWBOY MOUNT
See our full range of mounts at www.Replayxd.com
VHB SnapTray LowBoy Mount
Unlock
Lock
IMPORTANT
Use rubbing alcohol to clean
the mounting surface.Wipe
dry the surface. Apply your
VHB mount to surface. Press
and hold for sixty seconds to
allow adhesive to bond to
the surface. Bond strength
willincreasethrough time.
At room temperature,
wait for at least 24 hours
to achieve 90% bonding
strength, and 72 hours for
100%bonding strength.
ALIGNMENT
There are a few references for accurately aiming and aligning your Replay XD 1080 Mini.
1. The Start and REC button should always point up or at the 12 o’clock position for a level horizon.
2. The front silver sight markers are horizontal and vertical which act as a level.
3. The laser etched marks on the side of the Replay XD 1080 Mini are spaced every 15 degrees to give you ne
adjustment.
4. To make sure you are aiming your Replay XD 1080 Mini in the desired direction, simply look down the length of
the housing from the rear–forward as if you’re looking through a telescope. It’s that easy.
12
9
6
3
RIDING HEAD POSITION
ACTUAL LINE OF SIGHT
ACTUAL LINE OF SIGHT (HORIZON LINE)
MOUNTING
HEIMLOCK SWIVEL/TILT MOUNT
LOWBOY MOUNT
Mounting angle and setup:
1. When using a HeimLock mount or LowBoy mount it is important to mount them at an optimal position.
Please reference the illustration on this page for possible positions.
2. When mounting to a helmet, most people have a tendency to lower their head from 15º to and excess of 20º.
It is important to recognize what the natural angle or active position of your mounting locations are on items
such as: helmets, hats, handlebars, vehicle bodies, etc.This will help you to achieve the best angle and capture
professional looking video.
3. For best results have a friend look at your active riding & head position to choose your optimal camera angle
based on your riding position before applying yourVHB SnapTray.
Note: You can make a test recording and check it on an a Mac or PC.
See our full range of mounts and mounting ideas at www.Replayxd.com
1. Remove rear protective cap and connect the supplied mini USB
cable into the Replay XD 1080 Mini USB port.
2. Plug the USB cable into your PC or Mac USB 2.0 port, or our USB
Wall Adapter accessory.
3. The green charging status LED at the rear of the Replay XD 1080
Mini will illuminate to tell you it’s charging. When the green LED
turns o, the battery is full and charging is complete
Note: Charging through the PC/Mac USB port will take approximately
twice as long as using the USB Wall Adapter or Car Adapter. It is not
recommended to record while charging through the PC/Mac USB port
as the Replay XD 1080 Mini uses approximately the same power draw
as the PC/Mac USB port, damage to the Replay XD 1080 Mini or your
computer may occur.
TheReplayXD1080Mini will record for approx.130min. on afullcharge
inoptimal conditions.Extremeheat or coldcanaect batterylife.
SIDE VIEW REAR VIEW
PC/MAC
CHARGING
PC/MAC
MINI USB 2.0
CHARGE/SYNC
CABLE
DOWNLOAD
1. Remove rear protective cap and use option (1) or option (2).
2. Option (1):Take the microSDHC out of the Replay XD 1080 Mini
and use a SDHC compatible card reader to transfer your les to your
computer.
3. Option (2): Download from the Replay XD 1080 Mini USB port.
4. Plug USB cable into Replay XD 1080 Mini and a PC/Mac USB 2.0
port.
5. Press and hold the Start/Stop (B) and Power On your Replay XD 1080
Mini.
6. On a PC/Mac your Replay XD 1080 Mini will mount to your
computer as a mass storage device.You may download your video
les from the DCIM folder created on the microSDHC card.
(Always Eject device from PC/Mac)
Note: Option (2) may exhibit slower transfer speeds.
Playback through USB is not recommended as choppy
playback may occur. Download footage to PC/Mac rst.
PC/MACPC/MAC
MINI USB 2.0
CHARGE/SYNC
CABLE
SIDE VIEW
HOW TO ERASE FILES
1. Move selected video files or folders to yourTrash Can
orRecycleBin
2. For Mac: Go to Finder and select Empty Trash...
Note:SimplymovingfilesorfolderstotheTrashdoesnot
erase files from your memory card, it just moves them
(referenced in the Trash). Files are invisibly stored on
yourmemorycarduntiltheTrashis emptied.
REAR VIEW
B
Tabla de contenidos
Otros manuales de Cámara de acción de Replay XD
