Renson Healthbox 3.0 Manual de usuario
Healthbox®3.0
Anleitung
Manual Software version ≥ 0005
97
en
Healthbox®3.0
Introduction
This manual consists of 2 parts:
• Part 1 - User: guide to the operation of the device
• Part 2 - Installer: guide for performing a correct installation
General safety regulations
Always follow the safety regulations, warnings, comments and instructions from this
manual. If these safety regulations, warnings, comments and instructions are not followed, it could
lead to damage to the Healthbox 3.0 or to personal injury, for which RENSON®NV cannot be
held responsible.
• Installation of the Healthbox 3.0 must be performed in accordance with the general and locally
applicable regulations regarding construction, safety and installation requirements of the
municipal/urban and/or other bodies.
• Only a qualified electrician (or supported by a qualified installer) should install, connect,
commission and maintain Healthbox 3.0 differently than as described in this manual.
• All wiring must be done by a qualified person.
• Please ensure that the electrical power supply for Healthbox 3.0 corresponds to the
requirements in this guide.
• If the power cord is damaged, it must be replaced by the manufacturer, its service
representative or similar qualified persons to avoid danger.
• Healthbox 3.0 is constructed so that in normal use, and without deliberate action, it is not
possible to come into contact with moving or live parts.
• The device must be mounted in a touch-proof manner. This means that, under normal operating
conditions, no one can come into contact with moving or live parts of the fan unit without a
deliberate action such as:
– Disassembling the cover plate (and motor plate).
– Disconnecting an air duct and/or protective cover on the suction points during normal use.
98
en Healthbox®3.0
Specific measures
• Ensure that the Healthbox 3.0 remains easily accessible at all times, so that maintenance and
service can be done easily.
• Healthbox 3.0 meets the legal requirements for electrical devices.
• Modifications to the Healthbox 3.0 are not allowed.
• The fan unit may only be used with appropriate RENSON®accessories.
• Use RENSON®air ducts and a RENSON®roof guide to minimize the pressure drop.
Thisresults in lower energy consumption and lower noise fan noise.
• The installer must ensure that the air extraction of the fan unit is placed at sufficient distance
from the drainage and supply of the boiler.
• The possibility of touching the fan must be excluded. Therefore, an air duct network must
always be connected to Healthbox 3.0 before putting it in to service. The minimum channel
length is 0.5 m.
• When Healthbox 3.0 is combined with products for compartmentalisation to reduce the
distribution risk of fire:
Ensure that the fire valve/butterfly valve/sleeve/... has sufficient free air passage to minimize
pressure loss. Choosing the wrong type may lead to non-functioning of the Healthbox 3.0.
• DO NOT install Healthbox 3.0 in areas where the following items are present or may be
present:
– An excessively fat-laden atmosphere
– Corrosive or flammable gases, liquids or vapours
– Room air temperature above 50°C or lower than -10°C
– Relative humidity higher than 90% or outside
– Healthbox 3.0 should not be used in places where it may be subject to possible water jets
99
en
Healthbox®3.0
The following specific safety measures must be taken:
• Always ensure that before commencing work activities, the power supply is disconnected by
unplugging the power cord from the wall socket or by switching off the fuse. (ensure that this
has actually happened!)
• Always wait for a minimum of 30 seconds to reconnect the power supply.
• Use appropriate/suitable tools for performing work on mounting the Healthbox 3.0.
• Use the device only for applications for which it was designed, as stated in the manual.
Privacy Statement
If this unit is connected to the internet, it sends various unit information automatically to Renson.
For more information about this data processing, see www.renson.eu/privacy.
PLEASE NOTE:
The fan unit has to function permanently, i.e. the Healthbox 3.0 should never
be turned off. [legal obligation according to NBN D50-001 Chapter 4.2. System C)
If Air quality sensor data is used to display graphics (historical) to the user.
Asan installer you are not automatically entitled to access this sensor data of a
Healthbox 3.0 that you installed, conform General Data Protection Regulation
(GDPR).
If a customer’s Healthbox 3.0 is connected to your own account via a user app,
we recommend that you disconnect this connection to your account (via the user
app or web portal for users) before the customer takes the property into use.
100
Healthbox®3.0
en
User
PART 1 • USER
1 • Introduction
Congratulations on your purchase of Healthbox 3.0!
We are convinced that you have made the right choice. With Healthbox 3.0, your home is
correctly ventilated in an energy efficient way, giving you a healthy indoor climate:
• Protection against excessive moisture concentrations
• Supplied with good air quality
By automatically adjusting the ventilation level according to your living habits, heating leakage
is drastically reduced. If you chose the SmartZone option, you can also enjoy demand-controlled
extraction in the bedroom(s).
Via the SmartConnect connection, Healthbox 3.0 can be connected to the internet. This allows
Healthbox 3.0 not only to communicate with the user through a free app, but also with other
smart devices in smart home management systems.
Follow RENSON®and discover all innovations about mechanical ventilation!
www.fb.com/rensonworldwide
@rensonworldwide
@rensonworldwide
www.pinterest.com/rensonworldwide
www.youtube.com/user/RensonMarketing
2 • Healthbox 3.0 operation
Healthbox 3.0 was specifically developed for integration in residential homes and apartments,
but can also be used in the non-residential sector such as residential care centres, studios, etc. It is
a compact device, which means that it does not require a lot of installation space.
Proper functioning of the demand-controlled ventilation system is only guaranteed if the following
three pillars are adapted to one another:
• Supply: self-regulating RENSON®window ventilation class P3 or P4.
• Throughput: door grille or crack under the door.
• Drainage: Healthbox 3.0 demand-controlled fan unit.
101
Healthbox®3.0 en
User
2.1 • Demand-controlled ventilation
The demand-controlled ventilation system from Renson®is successful due to its comfort, energy
efficiency and ease of maintenance. The home is optimally ventilated according to the living
habits of the residents.
Healthbox 3.0 monitors the air quality 24 hours a day for CO2or moisture and/or VOCs (odour)
per connected room. The ventilation level is hereby intelligently fully automatically adjusted in
function of the measured air quality. This is done based on sensors in the control module. As long
as the air quality in a room is good, the ventilation level remains limited, which is very interesting
regarding energy in terms of heat savings and electricity consumption.
2.2 • Fan control
The fan is controlled via an active variable pressure control. This is a smart control that
continuously adjusts the fan speed to achieve the required ventilation air flows at the lowest
possible pressure level. This ensures extremely quiet operation as well as the lowest power
consumption.
2.3 • Breeze function
Healthbox 3.0 is standard equipped with a Breeze function. The Breeze function helps to limit the
risk of overheating inside the home.
What is the Breeze function?
When outside temperatures rise considerably during the day in summer, Healthbox 3.0 helps to
let in the fresh air at night.
The Breeze function becomes active to extract the warm indoor air more quickly in all rooms with
an increased flow rate and thus supply cooler outdoor air.
As a result, the Healthbox 3.0 contributes to the natural cooling of the residence.
Activating the Breeze function
Breeze control is automatic, but can only be active at night (between 0h and 6h) if the average
indoor temperature (measured on all control modules) is higher than the minimum temperature
(e.g. 24°C). The minimum temperature is freely adjustable in the app. The Breeze function must
be active for at least one hour.
102
Healthbox®3.0
en
User
3 • SmartConnect
With the SmartConnect connection, Healthbox 3.0 can be connected to the home network*.
This offers the occupant the following benefits:
• Home network connected to the
internet:
– The app (section 3.2) can be
used to visualise data about
the measured air quality from
the device and if necessary, to
temporarily manually adjust the
ventilation level where necessary.
– The Lio web portal can be
consulted (section 3.3).
– Healthbox 3.0 can be incorporated
into a smart home, to be integrated
into a home management system in order to communicate with other smart devices.
Allpossibilities for interaction can be fully used (section 3.4).
• Home network not connected to the internet:
– Healthbox 3.0 can be incorporated into a smart home to communicate with other
smart devices in a home management system. Interaction possibilities are rather limited
(section3.4).
3.1 • Connecting Healthbox 3.0 to the home network
To use the app and the web portal, the home network to which Healthbox 3.0 is connected must
be connected to the Internet. This way, it is possible to read out all data from the ventilation
system on the app, in order to adjust Healthbox 3.0 with the app, ...
NOTE:
Healthbox 3.0 always works completely autonomously, even if there is no
connection to the home network.
* private and secure network
Quick access to
instructional video
103
Healthbox®3.0 en
User
3.1.1 • Possible ways to connect Healthbox 3.0 to the home network
3.1.1.1 • Network cable
Instructions: connect Healthbox 3.0 directly to the router via a network cable.
3.1.1.2 • Ethernet-over-Power (EoP)
Instructions: connect both Healthbox 3.0 and router via network cable with a powerline ethernet
adapter.
Home network
router
Home network
router
Powerline ethernet
adapter
Powerline ethernet
adapter
Internet
Internet
104
Healthbox®3.0
en
User
3.1.1.3 • Wi-Fi dongle
Healthbox 3.0 is compatible to connect to secure Wi-Fi networks (WEP/WPA/WPA2).
Instructions: Insert the Renson Wi-Fi dongle into any USB connection of the SmartConnect zone (if
not already connected).
3.1.2 • Steps to connect Healthbox 3.0 to the app
First download the app (section 3.2.1) and start the app up until the Log in/Register screen. The
next steps to follow depend on how Healthbox 3.0 is connected to the home network:
1. Connection via network cable or Ethernet-over-Power (EoP)
2. Connection via Wi-Fi dongle
Wi-Fi dongle
Option: Use a Wi-Fi
repeater if there is
a bad Wi-Fi range
OR
Home network
router
Internet
If Healthbox 3.0 is live, Healthbox 3.0 must be disconnected from the power
supply after plugging in the Wi-Fi dongle. Wait for 30 seconds and put the
Healthbox 3.0 back on power.
105
Healthbox®3.0 en
User
3.1.2.1 • Connection via network cable or Ethernet-over-Power (EoP)
1. First, connect Healthbox 3.0 to the network via network cable or Ethernet-over-Power
(seesection 3.1.1).
2. Using the Wi-Fi settings of your smartphone, select the network (with internet) to which
Healthbox 3.0 is connected.
3. The connection between Healthbox 3.0 and the app must be made using the app.
Start the app and create an account by registering:
Router
network ‘x’
Router
network ‘y’
Network cable
or EoP
Wi-Fi settings
Network ‘x’
Network ‘y’
…
Internet
Otros manuales para Healthbox 3.0
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Admirador de Renson
Renson
Renson Endura Twist Manual de usuario
Renson
Renson Endura Twist Manual de usuario
Renson
Renson Healthbox II Manual de usuario
Renson
Renson Endura Twist Manual de usuario
Renson
Renson Fixvent Mono AK EVO Manual de usuario
Renson
Renson Waves Manual de usuario
Renson
Renson Cube Manual de usuario
Renson
Renson Invisivent AIR Manual de usuario
Renson
Renson 421 RC2 Manual de usuario
Renson
Renson Healthbox 3.0 Manual de usuario
