Renesas SDAH01 Manual de usuario

Evaluation Kit Manual

SDAH01

Evaluation Kit for the HS3001 Humidity and Temperature Sensor

R36UH0004EU0100 Rev.1.00

Aug 27, 2021

Page 1

The SDAH01 Evaluation Kit is used to assess the

HS3001 High-Performance Relative Humidity and

Temperature Sensor. The hardware allows users to

perform data logging experiments, and it can

communicate through a standard USB interface with

the user’s computer using the Demo Software. This

software can be used to view measurements in real-

time, adjust the resolution of the sensor, configure

measurement parameters, and download previously

logged measurements.

The evaluation board can be powered directly from

the USB port of the user’s computer or from a 1632

coin cell battery to enable fully autonomous

(untethered) data logging.

Board Contents

■SDAH01 evaluation board

■Three HS3001 sensor modules

■Sensor module extension cable

■USB cable

Features

■Relative Humidity Sensor Module with HS3001

sensor module:

●RH accuracy: ±1.5%RH

●Operating temperature: -40 to 105°C

■Demo Software:

●Data plotter

●Measurement resolution configuration

●Data export

■Sensor module extension cable allows extending

the HS3001 Sensor Module to different

measurement areas

Figure 1. SDAH01 Evaluation Kit

SDAH01 Evaluation Kit Manual

R36UH0004EU0100 Rev.1.00

Aug 27, 2021

Page 2

Contents

1. Functional Description.................................................................................................................................. 3

1.1 Setup and Configuration........................................................................................................................ 3

1.1.1. Computer Requirements......................................................................................................... 3

1.1.2. Software Installation and Setup .............................................................................................. 3

1.2 Kit Hardware Connections..................................................................................................................... 4

2. Using the EVK................................................................................................................................................ 5

2.1 Measurement Settings........................................................................................................................... 5

2.2 Exporting Data....................................................................................................................................... 6

2.3 Data Logging Mode (Untethered).......................................................................................................... 6

2.4 Data Logging Settings ........................................................................................................................... 7

2.5 Using the Plotter.................................................................................................................................... 7

2.6 Valid Settings Ranges........................................................................................................................... 7

3. Ordering Information..................................................................................................................................... 7

4. Revision History ............................................................................................................................................ 7

Figures

Figure 1. SDAH01 Evaluation Kit .............................................................................................................................1

Figure 2. Initial Display after Installation of the Demo Software...............................................................................3

Figure 3. Evaluation Kit Connections .......................................................................................................................4

Figure 4. Start Measurements..................................................................................................................................4

Figure 5. Measurement Settings ..............................................................................................................................5

Figure 6. Set Resolution...........................................................................................................................................5

Figure 7. Battery Installation.....................................................................................................................................6

Figure 8. Download Data to Demo Software............................................................................................................6

SDAH01 Evaluation Kit Manual

R36UH0004EU0100 Rev.1.00

Aug 27, 2021

Page 3

1. Functional Description

1.1 Setup and Configuration

1.1.1. Computer Requirements

A Windows®-based computer is required for interfacing with the kit and configuring the device. The user must

have administrative rights on the computer to install the Renesas Demo Software for the kit.

The computer must meet the following minimum systems requirements:

■CPU – Intel or compatible

■RAM – 512MB

■Operating system – Windows®XP / Vista / 7 / 8 / 10

■Ports – One available USB port

1.1.2. Software Installation and Setup

Complete the following procedure to install the Demo Software:

1. Plug in the USB flash drive to start the setup.

2. If the setup process does not start automatically, double-click on the Setup.exe file.

Figure 2. Initial Display after Installation of the Demo Software

SDAH01 Evaluation Kit Manual

R36UH0004EU0100 Rev.1.00

Aug 27, 2021

Page 4

1.2 Kit Hardware Connections

Complete the following procedure to set up the kit as shown in Figure 3:

1. Install the software from the USB flash drive or download from renesas.com as described in Software

Installation and Setup.

2. Connect one of the HS3001 sensor modules facing up, with or without the extension cable attached, into the

sensor module connector

3. Connect the USB port

of the board to the user’s computer using the supplied USB cable, and ensure that

the power switch

on the board is in the USB position. The “USB” LED

will light.

4. Run the Demo Software package from the Start menu, and click on the “Measure” button

. The

“Measuring” indicator

will blink whenever data is being captured.

Figure 3. Evaluation Kit Connections

Figure 4. Start Measurements

SDAH01 Evaluation Kit Manual

R36UH0004EU0100 Rev.1.00

Aug 27, 2021

Page 5

2. Using the EVK

2.1 Measurement Settings

To change the interval and number of measurements to be made, select Measurement Settings from the Tools

menu, enter the desired values, and then click OK, as shown in Figure 5. For the range of valid settings for these

two entry fields, see Valid Settings Ranges.

Figure 5. Measurement Settings

To change the measurement resolution, select Set Resolution from the Tools menu, select the desired

resolution, and then click OK, as shown in Figure 6. The resolution setting is stored on the sensor, and it will be

the default value applied when measurements are started. Measurement settings can be changed only when no

measurements are being taken.

Figure 6. Set Resolution

SDAH01 Evaluation Kit Manual

R36UH0004EU0100 Rev.1.00

Aug 27, 2021

Page 6

2.2 Exporting Data

The data displayed in the plotter area can be exported in two different formats.

■To export the measured data points in a Microsoft Excel®compatible comma-separated text file, select Save

Data from the File menu. Create a filename for the data, and select the location where the file will be saved.

■To export the plots themselves as a picture file, right-click on the plot area and select Save Image As. Create

a file name, select the location, and select the file type for the image.

2.3 Data Logging Mode (Untethered)

Disconnect the kit from the computer. Ensure that a battery is inserted in the battery holder on the back of the

board with the positive battery terminal facing away from the board, as shown in Figure 7.

Figure 7. Battery Installation

Complete the following to operate the kit in the data logging mode (see Figure 2).

1. To set the board to the data logging mode, put the power switch

in the “Batt” position.

2. To start data logging, hold the “Start/Stop Logging” button

for 3 seconds. The “Measuring” indicator

will light for 2 seconds and then start blinking on every logged measurement. This can be disabled to extend

the battery life by toggling the “L2 Enable” switch

3. To stop data logging, press the “Start/Stop Logging” button. The “Measuring” indicator blinks 3 times to

indicate the end of data logging.

4. To download the logged data to the Demo Software, connect the USB port

to the computer using the

supplied USB cable, and ensure that the power switch

on the board is in the USB position. The “USB”

LED

will light.

5. In the software, select Data Logging from the Tools menu and click on the Download Data button

shown in Figure 8. The maximum number of measurements that can be stored on the board is 2000.

Figure 8. Download Data to Demo Software

SDAH01 Evaluation Kit Manual

R36UH0004EU0100 Rev.1.00

Aug 27, 2021

Page 7

2.4 Data Logging Settings

To change the data logging measurement interval, select Data Logging from the Tools menu, and then click on

Change Interval. Enter the desired measurement interval, and click OK.

The data logging resolution can be selected in the same method as described in Valid Settings Ranges. Data

logging settings can only be changed when no measurements are being taken.

2.5 Using the Plotter

The plotter

displays the measured relative humidity and temperature data simultaneously versus time (see

Figure 3).

■Hold the left-mouse button, and drag it around an area to zoom onto that area.

■Hold the middle mouse or scroll button, and drag to pan across the plot area.

■To undo a zoom or pan operation, right click on the plot area, and select Un-Zoom (Un-Pan).

■The plot area can always be reset to the default view by right clicking on the plot area and selecting Undo All

Zoom/Pan.

■To display the measurement points on the plotted curves, right click on the plot area and select Show Data

Points. While moving the application window, measurements points will not be plotted.

2.6 Valid Settings Ranges

Measurement settings can be selected within the following ranges:

■Measurement interval: 0.5 to 3600 s

■Number of measurements: 1 to unlimited

■Data logging interval: 1 to 250 s

■Measurement resolution: 8, 10, 12, 14 bits

3. Ordering Information

Part Number

Description

SDAH01

SDAH01 Evaluation Kit, including SDAH01 evaluation board, HS3001 sensor modules, sensor

module extension cable, USB key with Demo Software, USB cable

4. Revision History

Revision

Date

Description

1.00

Aug 27, 2021

Initial release.

Corporate Headquarters

TOYOSU FORESIA, 3-2-24 Toyosu,

Koto-ku, Tokyo 135-0061, Japan

www.renesas.com

Contact Information

For further information on a product, technology, the most

up-to-date version of a document, or your nearest sales

office, please visit:

www.renesas.com/contact/

Trademarks

Renesas and the Renesas logo are trademarks of Renesas

Electronics Corporation. All trademarks and registered

trademarks are the property of their respective owners.

IMPORTANT NOTICE AND DISCLAIMER

RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL

SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING

REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND

OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible

for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)

ensuring your application meets applicable standards, and any other safety, security, or other requirements. These

resources are subject to change without notice. Renesas grants you permission to use these resources only for

development of an application that uses Renesas products. Other reproduction or use of these resources is strictly

prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.

Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,

damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject

to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources

expands or otherwise alters any applicable warranties or warranty disclaimers for these products.

(Rev.1.0 Mar 2020)

Tabla de contenidos

Otros manuales de Placa madre de Renesas

Renesas

Renesas RTKA788152DE0000BU Manual de usuario

Renesas

Renesas ISL78226EVKIT1Z Manual de usuario

Renesas

Renesas PG-FP6 Manual de usuario

Renesas

Renesas RX23W Series Manual de usuario

Renesas

Renesas RE01 15000KB Manual de usuario

Renesas

Renesas RH850/D1x Instrucciones de uso

Renesas

Renesas RAA223021 Manual de usuario

Renesas

Renesas QB-V850ESHG3-TB Manual de usuario

Renesas

Renesas RA9530-R Manual de usuario

Renesas

Renesas RA6T1 Series Manual de usuario

Renesas

Renesas RTKA211450DE0000BU Manual de usuario

Renesas

Renesas 8V9705 Series Manual de usuario

Renesas

Renesas ISL9122AIIN-EVZ Manual de usuario

Renesas

Renesas ISL94212EVKIT1Z Manual de usuario

Renesas

Renesas TXS25-4 Manual de usuario

Renesas

Renesas Intersil ISL73007SEHDEMO3Z Manual de usuario

Renesas

Renesas RTKA212831DR0000BU Manual de usuario

Renesas

Renesas RTKA214250DE0020BU Manual de usuario

Renesas

Renesas R0E420000MCU00 Manual de usuario

Renesas

Renesas RL78G14 Manual de usuario

Renesas

Renesas RL78/G10 Manual de usuario

Renesas

Renesas RH850/F1x Manual de usuario

Renesas

Renesas RTKA223011DE0000BU Manual de usuario

Renesas

Renesas RZ/G2L Guía del usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario