Rena DA615 Manual de usuario
RENA Direct Address Printer
DA615
Instruction Manual
This manual is written and verified thoroughly. Yet, we will not undertake liability for any fault.
Technical specifications may change due to design advances.
The data stated are nominal values only.
Order No. R0615.0.980 State 12.99
\text\etd\DA615\contents I.1 DA615 instruction manual
CONTENTS Page
Important notes on safety
1. Introduction 1.1
What can the DA615 address printer do ? 1.1
Presenting the DA615 address printer 1.2
Control panel 1.3
In off-line mode 1.3
In programming mode 1.3
Brief guide 1.4
2. Operation 2.1
Connecting the printer 2.1
Interface cable 2.1
Power cable 2.1
Switching the printer on 2.2
What does the display show ? 2.2
What do the keys mean ? 2.3
When are the keys active ? 2.4
OFF-LINE MODE 2.4
ON-LINE MODE 2.4
3. Addressing media 3.1
Adjusting the support height 3.1
Adjusting the print-head spacing 3.1
Transport direction 3.2
Lateral guides 3.4
Paper transport without address printing 3.4
Positioning the media 3.5
Positioning print areas 3.5
Pinwheels 3.7
Paper guide 3.7
Adjusting the print position 3.8
Address block rotation 3.8
Left margin 3.8
Clearance 3.8
Print test 3.9
Contents
\text\etd\DA615\contents I.2 DA615 instruction manual
4. Printing 4.1
Print cartridge 4.1
Which cartridges to use 4.1
When should the cartridge be replaced ? 4.1
Replacing the cartridge and resetting the ink counter 4.2
Cleaning the ink nozzles 4.3
Print test 4.3
Counting addresses 4.3
Counting test addresses 4.3
Counting received addresses 4.3
5. Printer functions 5.1
Programming mode 5.1
What is programming mode for ? 5.1
Getting to programming mode 5.1
What does the display show in programming mode ? 5.2
The key functions in programming mode 5.2
Menu overview 5.3
Explaining the menu fields 5.4
Example of an application in programming mode 5.14
Initializing the printer 5.14
6. Interfaces 6.1
Centronics parallel interface 6.1
Signal description 6.2
Pulse diagram 6.3
RS-232-C serial interface 6.4
7. Fonts 7.1
Terminology 7.1
Fonts 7.1
Serif or sans serif font type 7.1
Normal/italics 7.1
Spacing 7.2
Pitch 7.2
Dot size 7.3
Underlining 7.3
Expanded mode 7.3
Character spacing 7.3
Quality 7.4
Orientation 7.4
Character sets 7.5
7-bit character set 7.5
8-bit character set 7.5
Selecting fonts for your addresses 7.6
Contents
\text\etd\DA615\contents I.3 DA615 instruction manual
8. Error messages and hints 8.1
General error messages 8.1
Error messages for soft fonts 8.3
Notes on maintenance 8.3
9. Annex 9.1
A. Technical data A.1
B. Character sets B.1
7-bit character sets B.1
8-bit character sets B.4
C. Glossary C.1
D. Index D.1
E. Accessories E.1
Guide brackets E.1
Pinwheels E.2
Paper guide E.2
Variant list
Declaration of conformity
\text\etd\allege\ impnotes Important Notes on Safety
Important Notes on Safety
PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Keep them within easy reach for later use.
All direction and warning labels on instruments must be observed.
Setting up the
printer •When setting up the printer, ensure that it is positioned securely and is
level. If it is allowed to tilt, roll away or drop, injuries may result.
•The printer must be protected from moisture
Electrical
safety •When connecting the printer to the power supply, observe the rated
values for the power connection on the type plate.
•Check the voltage setting at the printer’s power input module.
•For reasons of electrical safety, the power connection socket must be
equipped with a grounded conductor contact.
•The printer has a double-pole fuse protection! In the event of fuse
failure, electrical parts in the instrument may still be live.
•Run the power supply cable so that no-one can trip over it. Also ensure
that nothing is placed upon the cable.
•If the printer remains unused over a longer period of time, disconnect it
from the power supply. This ensures that no damage will be caused by
voltage surges.
•Never open the printer. For reasons of electrical safety, it may be
opened only by authorized service personnel.
Operational
safety •Never touch the internal parts of the printer while it is running !
•To avoid damaging the printer, use only spares that have been
approved by the manufacturer.
Cleaning the
printer •Before cleaning, the printer must always be disconnected from the
power supply.
•Use no liquid or aerosol cleaning agents. Cleaning is best done with a
cloth dampened with water.
Let your service
partner check
the printer !
IN THE FOLLOWING CASES, DISCONNECT THE PRINTER FROM THE POWER
SUPPLY !
•The power cable or power socket are damaged.
•Liquid has penetrated the printer.
•The printer was exposed to moisture.
•If the printer does not function as described in the operating instructions,
or you can obtain no improvements with the aid of these instructions.
•The printer was dropped and/or the housing is damaged.
•If the printer shows clear signs of a defect.
Spares •In the event of repair, only original spares or those corresponding to the
original parts should be used.
Consult your service partner about all queries relating to service and repair. This will ensure that
your printer will operate perfectly at all times.
\text\etd\da615\Introduction 1.1 DA615 instruction manual
1. Introduction
What can the DA615 address printer do?
The DA615 address printer is an ink-jet printer ensuring a high-quality printout. It
prints addresses at the correct positions on media such as envelopes, cards,
brochures, magazines and other documents up to 10 mm in thickness.
A total of thirteen installed fonts lets you choose from a large selection of
different typefaces.
The width of the print area is 600 mm.
Printing is performed with standard exchangeable ink cartridges.
Introduction
\text\etd\da615\Introduction 1.2 DA615 instruction manual
Presenting the DA615 address printer
1. Control panel with display (see next page) 12. Mid-support (R0615.0.098)
2. Locking/unlocking print units H4-H3 13. Guide bracket 1 (R0615.1.076)
3. Locking/unlocking print units H2-H1 14. Guide bracket 2 (R0615.1.077)
4. Print media thickness setting 15. Wide guide bracket 3 (R0615.1.078)
5. Support setting 16. Wide guide bracket 4 (R0615.1.079)
6. Power terminal 17. Short guide bracket 5 (R0615.1.080)
7. Power switch 18. Short guide bracket 6 (R0615.1.081)
8. Switch for changing media transport direction 19. Knurled knob (K2913.029)
9. Interface (parallel) 20. Paper guide (R0615.2.051)
10.Interface (serial) 21. Inkjet – print cartridges
11a.Socket for control signal
11b.Connector for control signal (E0906.024)
Introduction
\text\etd\da615\Introduction 1.3 DA615 instruction manual
Control panel
In off-line mode
On-line mode
Off-line mode Measurement
of paper width
Start/stop
Paper transport Repeat print-out of
last address(es)
Print-out of a test address Programming mode
Measuring the transport speed Address rotation by 180°
In programming
mode In programming mode, menu settings are made on the printer. In this
mode, the upper line of key descriptors applies (END, NEXT, PREV,
ENTER)
End of program-
ming-mode Change activation between
Menu field and option field
Select next value Select previous value
in combination
with the power
switch
Key combination
Power on + Prog
Power on + Start
Meaning
Reset to works default
HexDump
Introduction
\text\etd\da615\Introduction 1.4 DA615 instruction manual
Brief guide
The table shown below lists the operating steps in correct sequence. It allows you
to perform a test print quickly without any prior knowledge. You can find the detailed
description of the various operating steps on the pages shown in the right-hand
column.
Operating step described on Page
Connecting the printer 2.1
Switching the printer on 2.1
Adjusting the height of the supports 3.1
Setting the print-head spacing 3.1
Transport direction 3.2
Adjusting the lateral guides 3.4
Paper transport without address printing 3.4
Positioning the media 3.5
Positioning the print areas 3.5
Print test 3.9; 4.3
\text\etd\da615\Introduction 1.0 DA615 instruction manual
1. Introduction 1.1
What can the DA615 address printer do? 1.1
Presenting the DA615 address printer 1.2
Control panel 1.3
In off-line mode 1.3
In programming mode 1.3
in combination with the power switch 1.3
Brief guide 1.4
Tabla de contenidos
Otros manuales de Impresora de Rena
Rena
Rena MACH 5 Manual de usuario
Rena
Rena AS-150 Manual de usuario
Rena
Rena DA-590 Manual de usuario
Rena
Rena MACH 5 Manual de usuario
Rena
Rena envelope imager III Manual de usuario
Rena
Rena XPS1000 Manual de usuario
Rena
Rena MACH 5 Manual
Rena
Rena MACH 5 Manual de usuario
Rena
Rena Mach 8 Manual de usuario
Rena
Rena MACH 5 Manual de usuario
