REMEHA P 420 Manual de usuario
P 420
Fuel oil/gas boilers
Remeha
Assembly
Instructions
300016854-001-A
EN
63193
2P 420 02/04/08 - 300016854-001-A
1 Package list
Package list : Before starting to assemble the boiler, refer to the table below to check if you have received all the packages required.
1. Boiler body +Accessories
Boilers supplied with an assembled body
For boiler supplied with the boiler body in bulk
2. Baffle plates
3. Casing
4. Cable channel
5. Control panel RC 1
6. Technical documents
Number of sections 8 9 10 11 12 13 14
Assembled boiler body - (contents depend upon model) 1111111
Number of sections 8 9 10 11 12 13 14
Frontsection 1111111
Specialintermediatesection 1111111
Normalintermediatesection 567891011
Rearsection 1111111
Commonaccessories 1PackageCS20CS20CS20CS20CS20CS20CS20
Lowerinsulation,boilerbody 1PackageCS51CS53CS53CS55CS55CS57CS57
Base frame - dimensions depend upon
model 1111111
Number of sections 8 9 10 11 12 13 14
Baffle plates 1 Package CS 30 CS 31 CS 31 CS 32 CS 32 CS 33 CS 33
Number of sections 8 9 10 11 12 13 14
Casing(commonparts) PackageRB21111111
Casing, variable parts Package MP2 - - 1 - - 1 -
Package MP3 1 - - 1 - - 1
PackageMP4-111222
Package MP5 - 1 - - 1 - -
Number of sections 8 9 10 11 12 13 14
Cable channel 1 Package CS 41 CS 42 CS 43 CS 44 CS 45 CS 46 CS 47
Number of sections 8 9 10 11 12 13 14
Technical documents
(Content depends upon country) 1Package1111111
3
02/04/08 - 300016854-001-A P 420
2 Boilers supplied with an assembled body
Manoeuvring the assembled boiler body
To manoeuvre the assembled body, it is possible to use the four
lifting rings located on the frame.
Hydraulic test:
Refer to view 10
Certain parts will have to be removed to carry out the hydraulic test.
Mounting:
For boilers with assembled boiler body, start assembly from figure 16
3 Mounting
Warning : Assemble the boiler in the order given by the
numbers of each figure, in compliance with all the
instructions.
Refer to the applicable price list for any optional features used.
Tools required
- 1 22 box spanner
- 1 Phillips screwdriver
- 1 hammer
- 1 putty gun
- 1 stanley knife
- 13 - 19 - 24 spanners
- 1 Allen key
- JDTE or JDTE Plus assembly tool
4P 420 02/04/08 - 300016854-001-A
Boilers supplied with an assembled body
•Hydraulic test:
Refer to view 10
Certain parts will have to be removed to carry out the hydraulic test.
•Mounting:
For boilers with assembled boiler body, start assembly from figure 16
For boiler supplied with the boiler body in bulk
Hydraulic test: Refer to view 10
Mounting: Assembly of the sections is done from back to front
as shown below, beginning with assembly view 1
Front - Rear
Boiler type Rear section Special intermediate
section
Normal intermediate
section Front section
P 420-8 1151
P 420-9 1161
P 420-10 1171
P 420-11 1181
P 420-12 1191
P 420-13 11101
P 420-14 11111
5
02/04/08 - 300016854-001-A P 420
1 Assembly of the base frame, delivered unassembled
M001233
1
M001234
2
2
3
3
6P 420 02/04/08 - 300016854-001-A
2 Fitting the brackets
Front - Rear
P 420-8 - P 420-10 - P 420-12 - P 420-14
P 420-9 - P 420-11 - P 420-13
`Fit the 2 rear holding brackets and secure them to the frame.
Use the corresponding holes following the indication on the frame.
`Position the lower insulation (fabric to the top) package CS 51 to CS 57. If necessary, adapt the length of or fold the lower insulation after
completing assembly of the casing.
3 Positioning the frame and the rear section
Establish the location of the frame on the basis of the opening direction of the furnace door and the length of the burner.
Position the rear section on the frame and prop it up.
Affix it to the brackets (2 screws HM 12x40/40 + 4 washers L12 + 2 nuts HM12).
Around every 100 mm, place points of silicon mastic (1 tube delivered with the accessories package CS 20) in the leak proofing groove in
the section using a gun.
Carefully introduce the leak proof thermocord into the leak proofing groove.
do not pull on the seal while inserting it. Otherwise, you may stretch it and reduce its thickness. You must not make the junction
point with the thermocord in the lower part of the section.
7
02/04/08 - 300016854-001-A P 420
4
Handle the nipples with gloves, there might be sharp
edges.
- Clean the bores and nipples. Coat with the lubricant supplied with
the sections.
(1) Sandpaper
(2) Lubricant (Supplied)
5
- Gently push in the 2 nipples.
8P 420 02/04/08 - 300016854-001-A
6 Assembling the sections
A : Thermocord
Special intermediate section in front of rear section.
Place the first special intermediate section, making sure that it is turned in the right direction, i.e. with the flattening groove against the
thermocord.
For safety reasons, insert an upper assembly rod (loose boiler body accessories package) into the holes in the 2 sections.
Push the section gently and simultaneously on the 2 nipples of the rear section with a hammer and a piece of wood positioned in line with
the bores.
9
02/04/08 - 300016854-001-A P 420
7
- Put the assembly tool in position.
- Tighten gradually so as to bring together the upper and lower connections evenly and simultaneously.
8
- Fit the remaining sections one by one in the order shown, proceeding as per the views 3-4-5-6.
-Leave the assembly tool in place.
10 P 420 02/04/08 - 300016854-001-A
9 Fitting the upper and lower assembly rods and the upper casing
supports
(1) Front - (2) Rear
- Fit the upper assembly rods (boiler body accessories) in the order
shown in the diagram above. Place the expansion spring and its
washer on each rod at the rear. Stop tightening the nuts when
the free space between the threads is around 2 mm.
- Fit the upper casing supports (package CS13) and the upper
cross-bars (package CS10-11-12-14) with the assembly rods
(boiler body accessories package) as per the details A-B-C-D.
- Fit the lower assembly rods in the order shown in the diagram.
- Remove the assembly tool.
Otros manuales para P 420
2
Tabla de contenidos
Otros manuales de Caldera de REMEHA
REMEHA
REMEHA Quinta Pro series Guía de solución de problemas
REMEHA
REMEHA Quinta Ace 135 Guía de solución de problemas
REMEHA
REMEHA Gas 320 Ace Manual de usuario
REMEHA
REMEHA Gas 210 ECO Manual de usuario
REMEHA
REMEHA Gas 350 L Manual
REMEHA
REMEHA GAS 310 ECO PRO Manual de usuario
REMEHA
REMEHA Avanta 18v Manual de usuario
REMEHA
REMEHA Gas 110 Eco 115 Manual
REMEHA
REMEHA Avanta Plus 35c Manual
REMEHA
REMEHA Gas 550 Manual
REMEHA
REMEHA Gas 210 ECO Guía de solución de problemas
REMEHA
REMEHA Gas 310 ECO Manual
REMEHA
REMEHA Gas 310 ECO Manual
REMEHA
REMEHA Quinta Pro 30 Manual
REMEHA
REMEHA Quinta Ace 135 Manual de usuario
REMEHA
REMEHA P 320-4 Manual del propietario
REMEHA
REMEHA Quinta Ace Guía de solución de problemas
REMEHA
REMEHA 24c Manual de usuario
REMEHA
REMEHA Quinta Pro 65 Manual
REMEHA
REMEHA Quinta Ace 30 Manual de usuario
