Regal Century VGreen Evo Guía
INSTALLATION MANUAL
AND USER GUIDE
VGREEN EVO™VARIABLE
SPEED MOTOR
2
VGREEN EVO™ VARIABLE SPEED MOTOR
INSTALLATION MANUAL AND USER GUIDE
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
• Read and follow all instructions carefully.
• Disconnect and lock out power before installation and maintenance.
Safety is emphasized throughout this Installation Manual and User Guide. These
are safety alert symbols and signal words.They alert the user to potential personal
injury hazards. Obey all safety messages to avoid possible injury or death or damage
to equipment and other property.
TABLE OF CONTENTS
1.0 INTRODUCTION........................................................................................3
2.0 QUICK START INSTRUCTION ..................................................................4
3.0 WIRING......................................................................................................4
4.0 OPERATING THE VGREEN EVO MOTOR .................................................5
4.1 Operating Mode.......................................................................................6
4.2 Override Mode .........................................................................................7
4.3 Pause Mode.............................................................................................8
4.4 Schedule Check Mode .............................................................................9
4.5 Schedule Set Mode........................................................................... 10-15
5.0 PRIMING.................................................................................................. 15
6.0 FREEZE PROTECTION............................................................................. 15
7.0 CARE AND MAINTENANCE ................................................................... 15
8.0 FAULT STATUS, MANUAL RESTART AND POWER
OUTAGES ................................................................................................ 16
9.0 TROUBLESHOOTING GUIDE ................................................................. 17
3
1.0 INTRODUCTION
The VGreen Evo™ motor is a cost-effective variable speed replacement pool
pump motor designed to provide pool owners with maximum savings over
traditional single speed motors. The variable speed design allows the motor to be
programmed at the optimal settings for the pool allowing for energy savings. The
VGreen Evo motor offers ease of installation with direct drop-in replacement for
all applications and features an easy to program user interface to allow for a
simplified user experience, making it the perfect choice for your next pool
installation or motor replacement.
VGreen Evo Motor Features:
• Freeze Protection
• Sealed Ball Bearings
• TEFC Design
• Rotation: CCWPE
• Single Phase
• 50/60 Hz
• Variable Speed Operation
(600 -3450 RPM)
• 303 Stainless Steel Shaft
• Class F Insulation
• 50°C Ambient
• Dual Voltage 230/115 VAC, Auto-Voltage Detect Enabled Device
Benefits:
• New simplified user interface allows for easier programming and motor setup
with the push of one button
• IPX5 moisture intrusion rating provides enhanced protection against moisture
• Lightweight, compact design, and rotatable mains wiring compartment
allows for ease of installation
• Available in both square flange and C-Face mounting configurations to allow
for replacement versatility
• UV and rainproof enclosure helps to protect against harsh weather conditions
to extend motor life
4
2.0 QUICK START INSTRUCTION
When power is applied to the VGreen Evo™ motor for the first time it will
automatically run the programmed default schedule. This feature ensures that the
VGreen Evo motor will re-start in the event of a power outage.
Refer to section 4.5 Schedule Set Mode - to view the default operating schedule,
or to set the VGreen Evo at one of the other operating schedules.
3.0 WIRING
SHOCK HAZARD
The VGreen Evo motor must be wired according to the locally adopted version of
the NEC. A licensed, qualified electrician should complete the wiring for this
product. The motor is designed to operate with 230/115 VAC single phase power,
and is equipped with auto-voltage detection.
The VGreen Evo motor is designed to handle a direct wire connection, the wire
insulation should be stripped to a length of approximately 0.33". The terminal
block is capable of handling solid or stranded wire up to 12 AWG in size. The
screw for the mains connections should be properly tightened to a torque value
of 10 in-lb.
UI Button
Connector
Dip
Switches
RS-485
Connector
Mains
Terminals
VGreen Evo™ motor
5
4.0 OPERATINGTHE VGREEN EVO™ MOTOR
The VGreen Evo™ motor is equipped with 5 different modes that can all be reached
by a series of button presses on the user interface as outlined in sections 4.1
through 4.5.
OPERATING
MODE
BUTTON
OVERRIDE
MODE
PAUSE
MODE
SCHEDULE
CHECK MODE
SCHEDULE
SET MODE
← Button / Auto Timeout
Press 1X →
←Button
←Auto
←Auto Timeout
Press 2X →
Press 3X →
Press
& Hold
→
Auto →
NOTE: The user can only reach each mode from operating mode, with the exception
of moving from schedule set mode to schedule check mode.
6
While the power
is off, the light
will be off and
the motor will
NOT be running:
4.1 OPERATING MODE
Operating Mode will automatically start once power is applied to the motor
and will run the preset or user defined schedule. To turn the motor off power
must be disconnected. The below illustrations show the different scenarios
possible during Operating Mode:
While in
Operating Mode
(during Priming)
light will be on
continuously and
motor will be
running:
While in
Operating Mode
(during Schedul
e
@ Running
RPM) the light
will be on
continuously, the
motor will be
running:
While in
Operating Mode
(during Schedule
@ 0 RPM) the
light will be on
continuously, the
motor will NOT
be running:
NOT RUNNING
RUNNING (any speed)
RUNNING (high speed)
NOT RUNNING
RUNNING (any speed)
RUNNING (high speed)
NOT RUNNING
RUNNING (any speed)
RUNNING (high speed)
NOT RUNNING
RUNNING (any speed)
RUNNING (high speed)
7
4.2 OVERRIDE MODE
The VGreen Evo™ motor is equipped with an Override Mode, which can be
engaged to temporarily run at 3450 RPM OR high speed if the motor is currently
operating at less than 3450 RPM. If the motor is operating at 3450 RPM there
will be no change in motor speed. Follow the illustrations below to operate
Override Mode:
To enter Override Mode
PRESS button 1 time:
To exit Override Mode
PRESS and HOLD button
for 3 seconds then
release:
Automatic timeout of Override Mode:
PRESS 1 Time
1x
21∕2sec 1∕8sec
24 HOURS
While in Override Mode light will blink slowly:
NOT RUNNING
RUNNING (any speed)
RUNNING (high speed)
PRESS & HOLD for 3 Seconds
3 sec
8
4.3 PAUSE MODE
The VGreen Evo™ motor is equipped with a Pause Mode that will allow the
user to temporarily stop the VGreen Evo motor for maintenance work without
disrupting the 24 hour schedule (i.e., for backwashing the filter). If the VGreen
Evo motor is currently running, the user can follow the below illustrations to
operate Pause Mode:
To enter Pause Mode
PRESS button 2 times:
While in Pause Mode light will blink slowly:
There is NO automatic timeout of Pause Mode:
1∕8sec 21∕2sec
NOT RUNNING
RUNNING (any speed)
RUNNING (high speed)
PRESS 2 Times
2x
24 HOURS
To exit Pause Mode PRESS
and HOLD button for 3
seconds then release:
PRESS & HOLD for 3 Seconds
3 sec
9
4.4 SCHEDULE CHECK MODE
The VGreen Evo™ motor is equipped with a Schedule Check Mode that will
allow the user to check which of the 8 available schedules the motor is
currently operating. The user can follow the below illustrations to operate
Schedule Check Mode:
Once the light turns back on, begin counting. The light will blink 1-8 times
depending upon the set schedule. Then, the light will turn off for 3 seconds:
Once the light blinking
sequence is complete the
light will turn off and the
motor will automatically
return to Operating Mode:
NOTE: You can enter Schedule Check Mode while the motor is in Operating
Mode.
To enter Schedule Check
Mode PRESS button 3
times. After pressing the
button 3 times, the light will
turn on for 3 seconds then
turn off:
PRESS 3 Times
3 sec
3x
1∕2sec 1∕2sec 3 sec
= CURRENT
SCHEDULE #
AUTOMATIC
RETURN TO
OPERATING
MODE
10
4.5 SCHEDULE SET MODE
The VGreen Evo™ motor is equipped with two sets of energy efficient
operating schedules: Schedule Set A and Schedule Set B. Schedule Set B is
California Energy Commission 2021 Compliant.
The 8 pre-programmed operating schedules for the Schedule Set A can be
seen in the table below.
To select this set of schedules the dip switch positions must be set to, #3 OFF,
#4 OFF.
SCHEDULE SET A
SCHEDULE
PRIME
(WHEN MOTOR STARTS
FROM A STOPPED
POSITION)
24 HOURS
TIME
HOURS
0-2
HOURS
2-4
HOURS
4-6
HOURS
6-8
HOURS
8-10
HOURS
10-12
HOURS
12-18
HOURS
18-24
Schedule 1
(Factory Default)
3 minute prime
@ 3450 RPM 3450 RPM 2750 RPM 1750 RPM 1150 RPM 0 RPM
Schedule 2 3 minute prime
@ 3450 RPM 3450 RPM 2850 RPM 1850 RPM 1250 RPM 0 RPM
Schedule 3 3 minute prime
@ 3450 RPM 3450 RPM 1750 RPM 1150 RPM 0 RPM
Schedule 4 3 minute prime
@ 3450 RPM 3250 RPM 1150 RPM 3250 RPM 0 RPM
Schedule 5 3 minute prime
@ 3450 RPM 1725 RPM
Schedule 6 None WATER FEATURE ONLY (1100 RPM) FOR USE WITH CONNECTED POOL PUMP TIMER
Schedule 7 None WATER FEATURE ONLY (1725 RPM) FOR USE WITH CONNECTED POOL PUMP TIMER
Schedule 8 None WATER FEATURE ONLY (3450 RPM) FOR USE WITH CONNECTED POOL PUMPTIMER
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Motor de Regal
Regal
Regal marathon PPA Series Manual
Regal
Regal genteq Evergreen CM Manual de usuario
Regal
Regal Century Manual
Regal
Regal genteq Evergreen OM Manual de usuario
Regal
Regal Genteq Evergreen OM Manual de usuario
Regal
Regal Genteq Evergreen IM Manual de usuario
Regal
Regal genteq Evergreen OM Manual de usuario
Regal
Regal genteq ECM Manual de usuario
Regal
Regal Century VGreen 270 Manual de usuario
Regal
Regal Genteq KRYO FORTRESS Manual de usuario
