Rear view safety RVS-6139Q Manual de usuario
1
What’s in the Box?
System connects to four (4) cameras
• 1 DIGITAL 9" T T LCD Quad View Color Monitor with universal
mount/stand and wire
• 2 66' Extension Cables for Backup Cameras
• 2 33' Extension Cables for Side Cameras
• 1 Remote Control
• 1 Power Connection Wire
• 1 Screw Kit for installation
3
Table of Contents
Introduction...................................................................................................4
Safety Information ..................................................................................5-7
Before Beginning Installation...................................................................8
Installation Guide.........................................................................................9
Wiring Camera & Monitor.................................................................10-11
Installing the Monitor ..............................................................................12
Installation Diagram .................................................................................13
Monitor Operation.....................................................................................14
Splitting & Splicing ...................................................................................15
Positioning.................................................................................................. 16
Power Harness ............................................................................................17
Monitor Dimensions..................................................................................18
Monitor Specifications.............................................................................19
Camera Dimensions...................................................................................20
Camera Specifications..............................................................................21
Camera Dimensions...................................................................................22
Camera Specifications..............................................................................23
Troubleshooting..........................................................................................24
Warranty.......................................................................................................25
Disclaimer ....................................................................................................26
Rear View Safety
4
Introduction
Congratulations on purchasing a Rear View Backup Camera
System! With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already
exists in your vehicle. The Backup Camera System should not be
used as a substitute for the standard rear view mirror or for any
other mirror that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located for-
ward of the back of the driver’s seat or in any location that is
visible, directly or indirectly, to the driver while operating the ve-
hicle.
Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
5
Reverse With Confidence™
Safety Information
Please read the entire manual and follow the instructions and
warnings carefully. ailure to do so can cause serious damage
and/or injury, including loss of life. Be sure to obey all applica-
ble local traffic and motor vehicle regulations as it pertains to
this product. Improper installation will void manufacturer’s
warranty.
USAGE
•The Rear View Camera System
is designed to help the driver
safely detect people and/or
objects helping to avoid
damage or injury. However,
you the driver, must use it
properly. Use of this system is
not a substitute for safe,
proper or legal driving.
•Never back up while looking
at the monitor alone. You
should always check behind
and around the vehicle when
backing up, in the same way
as you would if the vehicle
did not have the Rear View
Camera System. If you back
up while looking only at the
monitor, you may cause
damage or injury. Always
back up slowly.
•The Rear View Camera Sys-
tem is not intended for use
during exstensive back-up
maneuvers or backing into
cross traffic or pedestrian
walkways.
•Please, always remember,
the area displayed by the
Rear View Camera System is
limited. It does not display
the entire panorama that is
behind you.
Rear View Safety
6
INSTALLATION
•Electric shock or product
malfunction may occur if
this product is installed
incorrectly.
•Use this product within
the voltage range specified.
ailure to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to firmly affix the
product before use.
•If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may
touch a metal case, cover the
cable with a friction tape. A
short circuit or disconnected
wire may cause a fire.
• While installing the RVS
System be careful with the
wire positioning in order to
avoid wire damage.
•The RVS System should only
be used when the
vehicle is in reverse.
•Do not watch movies or
operate the monitor while
driving; as it may cause an
accident.
•Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
•Dropping the unit may cause
possible mechanical failure.
Safety Information
7
Reverse With Confidence™
Safety Information
IN NO EVENT SHALL SELLER OR MANU ACTURER BE
LIABLE OR ANY DIRECT OR CONSEQUENTIAL DAMAGES O
ANY NATURE, OR LOSSES OR EXPENSES RESULTING ROM
ANY DE ECTIVE PRODUCT OR THE USE O ANY PRODUCT.
If you have questions about this product, contact:
Customer Service:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: 1.800.764.1028
Rear View Safety
8
Before Beginning Installation
Before drilling please check that no cable or wiring is on the
other side of the wall. Please clamp all wires securely to reduce
the possibility of them being damaged while vehicle is in use.
Keep all cables away from hot or moving parts and electrical
noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed,
perform a system function test by temporarily connecting the
system. If the system seems to not be operating properly see
troubleshooting (page 17).
Before Beginning Installation
9
Reverse With Confidence™
Installation Guide
Camera Installation
1. Attach camera bracket close to rear marker lights, centered on vehicle.
2. Camera: Drill a 20mm (0.8in) diameter hole into vehicle body near the camera and
bracket. Insert camera cable into vehicle (be careful not to kink cable) and fit grommet
into hole. Apply sealant around grommet to increase resistance to water penetration.
Connect camera to the camera extension cable which runs inside the vehicle.
3. eed as much cable as possible into vehicle & clamp securely. This reduces the pos-
sibility of cable being hooked or snagged. The aviation camera cable uses aircraft
grade connectors which means the camera cable can be exposed to all weather ele-
ments.
4. Attach camera to bracket using screws provided and adjust the angle.
Wiring Camera
5. The power harness on this unit has 4 camera ports (BLUE-BACKUP, YELLOW-LE T,
BROWN-RIGHT, and BLACK- RONT.)
6. Each camera should be connected to its corresponding port. All that is needed for
the system to work is to connect the POWER (red) to 12V and the GROUND (black).
7. The camera and monitor can always be activated by manually pushing the power
button on monitor. This is in addition to utilizing the positive triggers.
8. As you may have noticed, there are also 3 multi-colored wires (blue, brown, yellow).
These are trigger wires, and when they are energized (12V) they will turn on their cor-
responding channel. The Blue wire will also turn on gridlines and sound.
9. The camera system can be wired to be powered “ON” the entire time the vehicle is on.
This is typical in RV and some commercial applications.
Rear View Safety
10
Installation Guide
FInfrared technology built
into camera IRs are activated
automatically according to the
lighting conditions.
FWhen using the postive trig-
ger functions (blue, yellow &
white wires) each trigger
function needs to work on a
seperate 12V+ source i.e. the
Yellow and White wires can be
wired to a turn signal circuit
etc.
FGrid lines function can be
turned on/off by manually
from menu. (See page 13)
Monitor
1. To Attach the Pedestal mount to the dashboard or to the headliner use self-tapping
screws and/or the adhesive pad.
2. Attach monitor to mount, and adjust mounting angle to allow optimum driver
viewing comfort. (see figure 1.1 on page 11)
Note: If connecting power
directly to battery, the camera
is always ON and therefore can
drain battery. Therefore it is
recommended to connect
power to an ignition switched
accessory power source.
Tabla de contenidos
Otros manuales de Monitor de Rear view safety
Rear view safety
Rear view safety G Series Manual de usuario
Rear view safety
Rear view safety RVS-96D Instrucciones de montaje
Rear view safety
Rear view safety RVS-6137-RCA Manual de usuario
Rear view safety
Rear view safety RVS-SA150 Manual de usuario
Rear view safety
Rear view safety RVS-97 Manual de usuario
Rear view safety
Rear view safety RVS-97QUAD-DVR Manual de usuario
Rear view safety
Rear view safety RVS-718-7 Manual de usuario
