Reactor Heavy Water 100-lap Manual de instrucciones de instalación
Heavy Water 100-lap
Instructions & Warranty
IMPORTANT! Register for your warranty
online at www.reactorwatch.com
p/n 10009 rev9-12
www.reactorwatch.com www.reactorwatch.com
Welcome
REACTOR watches were conceived,
designed and built to withstand the real
world of sport enthusiasts. We are very
proud of what we have accomplished
and we are excited to welcome you to
our ever-growing family.
While your REACTOR watch is built for
maximum durability, it should ALWAYS be
rinsed thoroughly after use in salt water.
Designed for the Water
Your REACTOR Heavy Water watch is
specially designed for regular use in
water, and the special side wings create
an air flow channel to allow water or
perspiration to drain or evaporate from
under the watch.
ALWAYS RINSE YOUR HEAVY WATER
WATCH THOROUGHLY IN FRESH WATER
AFTER USE IN SALT WATER!
www.reactorwatch.com www.reactorwatch.com
Heavy Water Features
Buttons referenced as B1-4 hereafter
EL/SETMODE
B1
B2
Your Heavy Water has these functions:
1) Normal time
Press B3 for temp, B4 for Time 2
4) Chronograph with 100-lap memory
5) Recall of lap times in 9 segments
6) Countdown timer
7) Alarm
Pressing B2 advances through these
functions in the order shown.
ST/LAP SP/RESET
B3
B4
www.reactorwatch.com www.reactorwatch.com
Setting the Time
With the watch in normal Time mode,
press and hold B1 to enter SET mode.
Press B3 to increase or B4 to decrease
value. Press B2 for next step.
1) Choose from 12H or 24H format.
2) Seconds, minutes, hours of Time 1.
Note “PM” will display in 12H mode
if hours advance past noon.
3) Year, month, calendar date.
Day of week is set automatically .
4) Set unit (F or C) for temp display
5) For Offset, see Temp instructions on
the following pages.
Press B1 again to exit SET mode.
While in normal time mode, you can:
1) Press B3 to view temperature
Will revert to day of week in 20 secs.
2) Hold B3 to toggle hourly chime
Symbol will appear above hours.
3) Press B4 to quickly view Time 2
4) Hold B4 to switch to Time 2.
www.reactorwatch.com www.reactorwatch.com
Time 2 Mode
Time 2 allows for second time zone
EL/SET
ST/LAP
MODE
SP/RESET
B1
B2
B3
B4
The Time 2 mode allows the watch to
display a second time zone, and includes
a second calendar to accommodate
distant locales that may be a day ahead
or behind your normal time setting.
Time 2 can be viewed quickly by a press
of B4 while in normal time mode. To set
Time 2, press and hold B4 for 5 secs.
Then press and hold B1 to enter set
mode and follow the instructions from
the previous page.
www.reactorwatch.com www.reactorwatch.com
Adjusting the Temp
With the watch in normal Time mode,
press B3 to see the current air or water
temperature. The temperature sensor
is located on the right side of the watch
between B3 and B4, and reads the temp
when B3 is pressed.
Due to its location, the temp reading can
be influenced by body heat, so an offset
feature has been added to correct for
this effect. You will see the offset
function as the final step of the time
set procedure. To determine the offset,
wear the watch in a room of known
temperature for at least 15 minutes.
Press B3 to read the temp, then compare
to the known temperature of the room.
Determine the offset by subtracting the
displayed value from the known temp,
and enter the result into the offset field.
For most accurate water temp readings,
the offset value should be left at zero.
www.reactorwatch.com www.reactorwatch.com
Using the Chrono
STOP
Middle line displays most recent lap time.
Bottom line displays cumulative time.
Press B2 to enter CHRONO mode. The
amount of free memory will display
briefly before switching to chrono view.
1) Press B3 to start the chrono.
2) Press B3 again at the conclusion of
each lap. Lap time will display for 10
secs then change to new lap time.
3) Press B4 to stop chrono. Final lap and
total time will be displayed.
4) Press and hold B1 to save to memory
or B4 to clear this segment.
B1
B2
B3
B4
www.reactorwatch.com www.reactorwatch.com
Lap Memory Recall
Middle line displays most recent lap time.
Bottom line displays cumulative time.
B1
B2
B3
B4
IMPORTANT! Run segments must be
saved in CHRONO mode to be available in
RECALL mode. See prior pg. for details.
Although your watch has 100-lap
memory, this memory can only be
divided into nine segments (RUNs 1-9).
Once all nine segments are used (even
if lap memory is still free), saving an
additional segment will delete RUN 1 and
shift all previous RUNs back one position,
recording the new segment as RUN 9.
www.reactorwatch.com www.reactorwatch.com
RECALL mode continued...
To enter RECALL mode, press B2 until
RECALL is displayed. The watch will then
display the last segment recorded along
with the date it was recorded. Press
B3 to change segments (RUNs 1-9).
To review a segment, press B4 to scroll
through all the available data:
• TOTAL time • AVErage lap time
• BEST lap time • SLOWest lap time
• Individual LAP times
To view a different segment, press B3 to
return to the segment select screen and
B3 again to change the segment.
To delete a particular segment, while
in the segment select screen, press and
hold B4 until DELETE displays. The
segment will be deleted.
To clear all segments, press and hold B3
until DELETE ALL displays and flashes
three times. Display will show DATA NO
indicating that lap memory is clear.
www.reactorwatch.com www.reactorwatch.com
The Timer has three modes that change
what happens when the timer reaches
zero. CD-STP is countdown stop, which
will countdown once and stop. CD-UP
is countdown – count up, which will
countdown, then count up until stopped.
CD-REP is countdown repeat, which will
countdown and repeat up to 99 times
(the repeat value must be set as the last
step of the setting process in this mode).
In any mode, hold B4 to reset the timer.
Countdown Timer
From the time mode, push B2 three
times to enter Timer mode. Push and
hold B1 to enter set mode - the current
timer mode will flash. Press B3 to
change mode (explained at right).
Press B2 to change set point. Push B3 to
advance and B4 to retard value. Push B1
when all values are set. Press B3 to start
or stop the timer and hold B4 to reset
the timer to the initial set value.
Tabla de contenidos
Otros manuales de Mirar de Reactor
