RCA 20F650TECY Manual de usuario

Television

User's Guide

Changmg Entertainment.

mportant nformation

RISKOFELECTRICSHOCK

DONOTOPEN

This symbol indicates that this product incorporates double

insulation between hazardous mains voltage and user

accessible parts. When servicing use only identical

replacement parts.

Caution: To reduce the risk of electric shock, do not remove cover {or back], No user serviceable

parts inside, Refer servicing to qualified service personnel.

_. This symbol indicates important AThis symbol indicates "dangerous voltage" inside the

instructions accompanying the _. product that presents a risk of electric shock or

product, personal injury.

WARNING

To reduce the risk of fire or electric shock,

do not expose this product to rain or

moisture.

The apparatus shall not be exposed to

dripping or splashing and that no objects

filled with liquids, such as vases, shall be

placed on the apparatus.

Refer to the identification/rating label located on the

hack panel of your product for its proper operating

voltage.

FCC Regulations state that unauthorized changes or

modifications to this equipment may void the user's

authority to operate it.

Caution: Using video games or any external accessory

with fixed images for extended periods of time can

cause them to be permanently imprinted on the

picture tube (or projection ]_/picture tubes). ALSO,

some network/program Iogos, phone numbers, etc.

may cause similar damage. This damage is not covered

by your warranty.

Cable ]_/Installer: This reminder is provided to call your

attention to Article 820-40 of the National Electrical

Code (Section 54 of the Canadian Electrical Code, Part

1) which provides guidelines for proper grounding and,

in particular, specifies that the cable ground shall be

connected to the grounding system of the building as

dose to the point of cable entry as practical

Product Registration

Please fill out the product registration card (packed separately] and return it immediately. For US.

customers: Your RCA Consumer Electronics product may also be registered at www.rca.com/

productregistration. Registering this product allows us to contact you if needed.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here

and record the serial and mode[ numbers. These numbers are located on the product.

Model No. Serial No. Purchase Date:

Dealer/Address/Phone:

Tabte of Contents

Chapter 1: Connections & Setup

Things to Consider Before You Connect ....................................................................... 3

Protect Against Power Surges ........................................................................... 3

Protect Components from Overheating ........................................................... 3

Position Cables Properly to Avoid Audio Interference .................................... 3

Important Stand and Base Safety Information ................................................ 3

Use Indirect Light ............................................................................................... 3

Cables Needed to Connect Components to Your TV ....................................... 3

TV + DVD + VCR .............................................................................................................. 4

Explanation of Jacks ....................................................................................................... 5

The Front of Your TV ...................................................................................................... 5

Front Input Jacks ................................................................................................ 5

Front Panel Buttons ........................................................................................... 6

Plug in theTV .................................................................................................................. 6

Put batteries in the remote ........................................................................................... 6

How to Use the Remote Control to Complete the Initial Setup ................................ 6

Turn on the TV................................................................................................................. 7

Complete the Initial Setup ............................................................................................. 7

Complete Auto Channel Search ........................................................................ 7

Chapter 2: Using the Remote Control

Button Descriptions for TV Mode .................................................................................. 8

Button Descriptions for DVD and VCR Modes .............................................................. 8

Using the INPUT Button ..................................................................................... 9

Programming the Remote to Operate Other Components .......................................... 9

Find Out If You Need to Program the Remote ................................................. 9

Programming the Remote ................................................................................. 9

How to Use the Remote After You've Programmed It .................................. 11

Remote Control Codes .................................................................................................. 11

Chapter 3: Using the TV's Features

Channel Banner ............................................................................................................ 13

Why You Should Use the Auto Tuning Feature ........................................................ 13

How to Set Up the Auto Tuning Feature ........................................................ 13

Parental Controls and V-Chip ..................................................................................... 14

How V-Chip Works ........................................................................................... 15

USA V_Chip Rating System ............................................................................... 15

Canadian English V-Chip Rating System ......................................................... 16

Yable of Contents

Canadian French V-Chip Rating System .......................................................... 17

USA V-Chip TV Rating Limit ............................................................................. 17

Blocking Specific Content Themes .................................................................. 19

Viewing Specific Content Themes ................................................................... 19

Blocking Canadian V-Chip Ratings .................................................................. 20

V-Chip Movie Rating Limit ............................................................................... 20

V-Chip Exempt Program Block ......................................................................... 20

KidPass .............................................................................................................. 21

V-Chip Active .................................................................................................... 21

Front Panel Lock ............................................................................................... 21

Change Password ............................................................................................. 21

Chapter 4: Using the TV's Menu System

Sound Menu .................................................................................................................. 22

Picture Menu ................................................................................................................ 22

Setup Menu .................................................................................................................. 23

Parental Control Menu ................................................................................................ 24

Time Menu .................................................................................................................... 24

Chapter 5: Other Information

Troubleshooting ............................................................................................................ 25

Care and Cleaning ........................................................................................................ 27

Limited Warranty ......................................................................................................... 27

Things to Consider Before You Connect

Protect Against Power Surges

•Connect all components before you plug any of their power cords into the wall outlet,

• Turn off the I1/and/or component before you connect or disconnect any cables.

• Make sure aH antennas and cables are properly grounded, Refer to the Important Safety Instructions

packed separate]y.

Protect Components from Overheating

• Don't block ventilation holes on any of the components. Arrange the components so that air can

circulate freely.

• Don't stack components.

• If you place eompone_ts in a stand, make sure you allow adequate ventilation.

• If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it won't

flow around other components.

Position Cables Properly to Avoid Audio Interference

• Insert each cable firmly into the designated jack.

• If you place components above the I_, route all cables down the side of the back of the _/instead

of straight down the middle of the IX/.

• If your antenna uses 3OO-ohm twin lead cables, do not coil the cables. Also. keep the twin lead

cables away from audio/video cables.

Important Stand and Base Safety Information

Choose the location for your IV carefully. Place the _/on a stand or base that is of adequate size and

strength to prevent the ]V from being accidentally tipped over, pushed off. or pulled off. This could

cause personal injury and/or damage the _/. Refer to the Important Safety Instructions packed

separately.

Use Indirect Light

Don't place the 1V where sunlight or room lighting will be directed toward the screen. Use soft or

indirect lighting.

Cables Needed to Connect Components to Your TV

The pictures below show the cables needed for the connections represented in this book.

Coaxia_ came S Video cable Audio/Video cables

Chapter 1 Graphics contained within this publication are for representation onl}4 3

Connections Set p

VCR

fVIDEO gUDIO

o°,00

or Ant_nfla

TV (back panel)

TV + DVD + VCR

1. Connect your DVD Player to your 1V.

A. Connect the audio (white and red) cables to the R and L/MONO AUDIO jacks on the back of the

TV and to the Audio Output jacks on the DVD player.

B, If your DVD player has an S-Video jack, connect an S-Video cable to the S-Video jack on the DVD

player and to the S-VIDEO [N jack on the back of the _/, If your DVD player doesn't have an

S-Video iack, go to C.

-OR-

C. Connect a video cane {yellow) to the Video Output Jack on the DVD player and to the VIDEO jack

on the back of the _I.

2. Connect your TV to your VCR

Connect a coaxial cable to the _I ANT jack on your _I and to the Output Jack on your VCR

(sometimes labeled OUTTOIV),

3. Make sure cable or antenna is connected to your VCR.

Connect the coaxial cable from your cable outlet or antenna to the antenna input on the VCR,

Go to page 6

4Graphics contoined within this publicotion ore for representotion onl_ Chapter 1

Connections Setup

Explanation of .lacks

Thissection describes the jacks you can use to make connections, Thereare several

ways to connect components to your IV,

IV ANT Letsyou connect acoaxial cable to receivethe signal from the antenna,

cable,cable box, or if using the example on page 4,a VCR,

B LiMONO

AUDIO VIDEOS-VIDEOIN

,=: VIDEO I

VIDEO, AUDIO R and L/MONO Lets you connect a

component such as a VCR, DVD player, or laserdisc player.

• R {RIGHI) AUDIO Provides right audio connection The

right audio connector is usually red.

• L/MONO AUDIO Provides left audio connection The

left audio connector is usually white,

• VIDEO Provides composite video connection, The video

connector is usually yellow.

S-VIDEO IN Provides better picture quality than the

video jacks because the color part of the signal is

separated from the black and white part of the picture,

When using S-VIDEO IN, make sure to connect left and

right audio cables to the L/MONO and R AUDIO Input

jacks.

The Front of Your IX/

Front Input Jacks

The IV has front input jacks for your convc_Rence: one set of

audio/video inputs and a headphone jack. To access the

compone_t you connected to the front of the IV, press the

INPUT button on your remote until FRNTappears on the

screen, The jacks are ideal for connecting a video game

console or a camcorder.

Note:Whenconnecling ocomponenl lhol hasonly one oudiojock,

suchassomecamcorders,usethe TV'sAUDIOL/MONOjack toheor

the audio

VIDEO Receives video from another component such as a

VCR, camcorder, or video game console,

L/MONO and RAUDIO Receivesaudio from another

component such asaVCR,camcorder,or video game console,

PHONES Allows you to connect headphones to listen to the

sound coming from the IV.

Chapter 1 Graphics contained within this publication are for representation onl R 5

Connections Setup

Front Panel Buttons

If you cannot locate your remote, you can use the front panel buttons of your TV

to operate many of the _/'s features.

MENU/OK Brings up the Main menu. In the menu system, it selects highlighted

items.

CH- Scans down through the current channel list. In the menu system, acts like

the down arrow button on the remote control and adjusts menu controls.

CH+ Scans up through the channel list. In the menu system, acts like the up

arrow button on the remote control and adjusts menu controls.

VOL- Decreases the volume. In the menu system, acts like the left arrow button

on the remote control and adjusts menu controls.

VOL+ Increases the volume. In the menu system, acts like the right arrow button

on the remote control and adjusts menu controls.

POWER Turns the I_ on and off

Plug in the TV

Plug the endof the power cord into a grounded wall outlet. Insert the plug

completely into the outlet.

Put batteries in the remote

• Remove the battery compartment cover from the back of the remote by

pushing down on and sliding off the cover.

• Insert 2 "AAA" fresh batteries, Make sure the polarities {+ and -) are aligned

correctly.

• Replace the cover.

/Arrows

button

How to Use the Remote Control to Complete

the Initial Setup

The technical term is "Navigation"- how you move through

the on-screen menus, The method is the same throughout

the menu screens: highlight your choice and select it,

To highlight a menu item, press the arrow buttons on the

remote to highlight one of the items listed on the screen.

Use the up or down arrow button to move up or down. Use

the right or left arrow button to move right or left.

To select the item that you've highlighted, press OK.

Note H_ghlighledmeanslhat themenu _ternslands out from olher

menu itemson theI_sl¸_ppears darker,brighl_r, or _differenl¸color}¸

6Graphics contained within this pu61ication ere for representation only Chapter 1

Connections Setup

Turn on the TV

PressIV on the remote, or press POWER on the Ivs front panel.

Note:Pressinglhe TVbu_Lunhal only turnson lhe T_,bul pul_ Lhcrcmolc mto I1/mode "TV

mode"mcons that the'buttonson theremoteconltol operateLh_ TV'sfunclions

Complete the Initial Setup

The menu system in your 1V allows the ]V's features to work

properly. The first time you turn on your IV, the SETUPsereen

appears with Language highlighted. The default language is

English. To choose another language, press the right arrow

button on the remote.

Complete Auto Channel Search

This part of the setup allows the IV to search for all channels

viewable through your antenna or cable IV system. This is

sometimes called auto programming.

I, Highlight Auto Ch. Search and press OK.

2. The Signal Type option is set to Cable. To change the

option to Antenna, press the right arrow button and then

press OK.

3 Pressthe down arrow button to highlight StarL Press OK

to begin the auto channel search.

Once the search is complete, you can begin watching IV, For

information on customizing your channels or menu options,

go to Chapter 4.

Chapter 1 Graphics contained within this publication are for representation onl}4 7

Indicator Button Descriptions for TV Mode

Arrows Usedto highlight different items in the _/menu and to adjust the menu

controls.

Indicator Indicates the programming mode when programming the remote to

control components. Lights when you press a valid button on the remote. Flickers

when a button is pressed and the batteries are low.

{0-9) Number Buttons Enter channel numbers and time settings directly

through the remote control.

To enter a one-digit ehannd, enter a zero first. To enter a two-digit ehannd, press

the two digits and expect a few seconds delay. This is if you want to enter a third

digit.

CC Toggles dosed captioning on and off.

CH + or CH - Scans up or down through the current channel list. Press once to

change the ehannd up or down; press and hold to continue changing ehannds.

CLEAR Removesany menu or display from the screenandreturns you to normal

viewing.

GO BACK Returns you to the previous channel.

INFO Brings up the channel banner.

INPUT Joggles through the available input sources (VtDI. SVID. FRN1,and current

channel}.

MENU Brings up the Main menu,

MUTE Reduces the W's volume to its minimum level Press again to restore the

volume,

OK When in the menu system, selects highlighted items,

ONoOFF When in JV mode, turns the JV on and off. If in another mode (VCR,

DVD, ete,] and programmed, will turn the component on and off.

PRESETS Brings up sound and picture presets,

SKIP Pressonce before changing channels and the ]!/will wait 30 seconds before

returning to the original ehannd. Press repeatedly to add more time.

TV Turns on the TVand puts the remote in TV mode. ADo displays current status.

VOL - or VOL + Decreases or increases the J!/'s volume.

Button Descriptions for DVD and VCR Modes

AGAIN In DVDmode, replaysthe last severalsecondsof the title you're playing.

ANTENNA InVCRmode,functions asa W/VCRbutton.

DVD Putsthe remote in DVDmode and, if auto tuning isenabled,will turn on

the TVandtune to the correct video input channel.

GUIDE If you're operating another component that hasa guide, this button

accessesthe on-screen Guide.

OPEN,CLOSE In DVDmode, opensor closesthe DVDdisc tray.

8Graphics contained within this puGlication are for representation only. Chapter 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de TELEVISOR de otras marcas

Philips

Philips Colour Television Manual de usuario

Toshiba

Toshiba 27A10 Manual de usuario

Philips

Philips 42PF9630A/37 Manual de usuario

Hitachi

Hitachi 32FX48B Manual de usuario

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario

Changhong Electric

Changhong Electric uhd55b6000is Manual de usuario

Philips

Philips Matchline 21CE7551 Manual de usuario

Panasonic

Panasonic Genus TX-G10 Manual de usuario

Toshiba

Toshiba 19A20 Manual de usuario

Philips

Philips 25PT4523-16 Manual de usuario

Sony

Sony XBR-100Z9D Manual de usuario

Philips

Philips PR0930X3 Manual de usuario

Philips

Philips Brilliance 231P4QPY Manual de usuario

Samsung

Samsung 55S9 B Series Manual de usuario

Philips

Philips 32HF9385D Guía de solución de problemas

Sharp

Sharp LC-40FI5012E Manual de usuario

Loewe

Loewe Table Stand Reference 55 Manual de usuario

Philips

Philips 32PFH5300 Manual de usuario