RC Lander F9F-2 Guía de inicio rápido
F9F-2
OPERATIONAL MANUAL
7 different color to meet customer’s choice. 2 different material
F9F-2/OB:
F9F-2/TB:
F9F-2/YB:
F9F-2/WR:
F9F-2/GYR:
F9F-2/GRW:
F9F-2/BRY:
Original Blue
Tail Blue
Yellow/Blue
White/Red
Gray/Yellow/Red
Gray/Red/White
Blue/Red/Yellow
1. EPS
2. SEPO
3 PC-Cover
- 2 -
Please read before operating this system!
We would like thank you for purchasing our new product—F9F-2, designed for the
hobby enthusiast. Base on its full - scale counterpart, this USAJet can finish loops,
inverted flight and rolls and other aerobatics easily. Even the beginner can easily
setup the model and fly it stably. It is also made as a highly maneuverable model
for the intermediate to expert pilot. With the F9F-2 model which includes EDF set*,
speed controller, electric servo and landing gear with front steering (retract landing
gear & flap system are optional requirement) you will have joyful time in model
flying.
Remarks:* We have two types EDF set for your selection.
1) EDF68-1AP is standard equipment.
2) EDF68-1Ais a higher grade EDF set which is an aluminum alloy material EDF
more powerful output, efficient and durability.
3)Please be noticed that all servo have been pre-set the center point before out of
factory. It maybe appeared some difference due to difference band mark radio
control. Kindly make sure to do the adjustment (special to pre-set the travel of
gear servo up to 130 %. If you select gear doors system with special
modified travel throw servos. You are needed to pre-set the travel of gear
servo up to 110-120%) with your own radio equipment before installation this jet
model.
4) From main wing edge to center 70-75mm is the CG point.
5) Please make sure to use a little piece of attached magic sticker for your LiPo
battery for fixing on the position before on flight.
- 3 -
Specifications:
Wing Span : 1050mm
Len
g
th: 1000mm
Height: 300mm
Flying weight: 1150g up
Servo: 9g×5pcs or9pcs
Power system: Brushless electrical ducted fan
Thrust: Up to 1200g with 3s
Up to 1450g with 4s
Up to 1600g with 6s
Function: Retract landing gear system,full scale flap performance(optional), Gear doorssystem.
ESC: 55Aor above
Radio: 5 to 6 CH
Battery: Li-po 11.1v/3s-3300mAh or above &
Li-po 14.8v/4s-3300mAh or above
- 4 -
EDF SYSTEM
EDF68-1A
Material:
A
luminium Alloy,Metal special
Weight: Ca. 90g(Motor not included)
Rotor: 68mm dia,5-bladed.
Max rpm 45,000 rpm
A
pplication: 200-700W
Static Thrust: Up to 1.45kg(14.21 N ,48.3oz)
Related product
1. LEDF68-1A43
2. LEDF68-1A39
3. LEDF68-1A35
4. LEDF68-1A21
EDF68-1AP
Material:
A
luminium Alloy,Metal special
Weight: Ca. 80g (Motor not included)
Rotor: 68mm dia,5-bladed.
Max rpm 40,000 rpm
A
pplication: 200-500W
Static Thrust: Up to 780g(7.35N ,25oz)
Related product
LEDF68-1AP39
Caution:
1. EDF during working ,please don’t overload the current high-point.
LEDF68-1A39﹍﹍﹍ 40A@60s;45A@30s;50A@10s (4S/3S Li-po)
LEDF68-1A35 ﹍﹍﹍45A@60s;50A@30s;55A@10s;(４SＬi-po)
LEDF68-1A43﹍﹍﹍ 50A@60s;55A@30s;60A@10s;(3S Li-po)
LEDF68-1A21------------60A 65A 80A (6S li-po)
LEDF68-1AP39﹍﹍﹍ 35A@60s;40A@30s;45A@10s;(3S Li-po)
2. EDF will getting heat during working ,please control the tail pipe temperature under 75 degree.
3. Please don’t make any testing run of EDF unit by hand hold method, It maybe cause any danger to you or damages the unit possibly.
- 5 -
It must be installed into the plane body or test stand for operation.
4. Please don’t remove any parts of this unit by yourself. Since it has been done well balancing procedure. Otherwise it may be affected
the performance after any removal action.
MainAccessories
MAIN WING SET WING FUELTANK (RIGHT & LEFT) HEADER COVER
EDF COVER SET CANOPY SET
LANDING GEAR HOSUING SET
INTAKE SET (RIGHT&LEFT) MAIN FUSELAGE
LOWER FRONT FUSELAGE
EXHAUST COVER SET HORIZONTALSTABILIZER
VERTICALSTABILIZER
Remarks: 1) Operational Manual (included)
2) 5 Min. epoxy set (included)
- 6 -
3) Extension cord x 2 & Y cord x 3 (not included)
4) Push rods for Elevator, Rudder,Aileron, Retract Gear & Steering (included)
5) One plastic bag includes screws, Control Horns, LinkageStoppers & Retract Landing Gear.
Assembling the aircraft
Take out the elevator from the horizontal stabilizer
Use the epoxy set to glue up the elevator
Install the elevator & rudderservo into the vertical stabilizer
Take out the ruder from the vertical stabilizer first
- 7 -
Put the horizontal stabilizer into vertical stabilizer with epoxy
Then link up the rudder and glue up with epoxy
Please link up both servo of rudder & elevator with the extension
cord first
Install those into the main fuselage with epoxy.
Then install the intake set (right & left) into the main fuselage.
- 8 -
Install the front retract landing gear & battery hard wood platform
Glue the lower front fuselage into main fuselage
Take out the aileron from the main wing
Use the epoxy set to glue up into the main wing
Install the main retract landing gear
- 9 -
Install both of wing fuel tank into main wing with epoxy
Install the canopy plastic lock up set
The canopy set is used push in method to install into main
fuselage and push down the front canopy with click to lock up.
Hand holds the front canopy and pull up to open it for changing
the battery or doing any maintenance issue.
The final action is installed the main wing into the main fuselage
with enough epoxy. Please be reminded that you need to make
sure the servo of landing gear, and flap and related extension
cords link up well before glue up the main wing.
- 10 -
Install the EDF set and ESC system
Lock up the EDF cover set
Link up the elevator push rod
Link up the right & left aileron push rods
Tabla de contenidos
Otros manuales de Juguete de RC Lander
