Rangevision SPECTRUM Manual de uso y cuidado

RANGEVISION

Setup and calibration

SPECTRUM

Contents
Contents 2
Introduction 3
Technicalspeciﬁcations 4
3Dresolution 4
Systemrequirements 4
Preparingforwork 5
Packagecontents 5
Installingsoftwareanddrivers 7
Settingupyourcomputerforworkwiththe scanner 8
Connectingprojector 8
Conﬁguringcomputerparameters 9
ScannerAssembly 10
Scannersetup 11
ScanCenterNGlaunch 11
Selectscanningzone 12
Calibrationﬁeldparameters 13
Placingthecalibrationplate 13
Initialsetupofcamerasandlenses 14
Checkingcameraarrangement 15
Findingaworkingdistance 15
Adjustmentoftheprojectorfocus 16
Bringingthecamerastogether 16
Finalcalibrationofthecameras 17
Calibratingthescanner 21
Calibrationplate 21
Fullcalibration 23
Fastcalibration(orientation) 25
Focus assessment during calibration 27
2

Introduction

ThankyouforchoosingRаngeVisiоnSpectrum!

PleasereadthismanualbeforeusingRangeVision3Dscanner.Herearedescribed the

procedures for preparing the scanner, installing the required drivers, calibration

procedure, scanning procedure,andtipsforacquiringhigh-quality three-dimensional

object model.

Informationmaybeamendedfromtimetotime.Thesechangeswillbeinserted into the

new versionsofthemanual,orintheadditionaldocumentsandpublications.

Technicalspeciﬁcations

Scanningzone

Scanning Area (WxHxD) (mm)

520*400*400

320*250*220

120*90*100

3Dpointaccuracy

0.12mm

0.06mm

0.04mm

Model

Spectrum

Resolutionofcameras

3Mpix

Diagonalofthematrix

1/2”

Texturescanning

Yes

3Dresolution

Scanningzone

3Dresolution

0.25mm

0.15mm

0.06mm

Operationdistance

1.05m

0.6m

0.3m

Systemrequirements

●operatingsystem-Windows7/8/1064bit,

●processor-IntelCorei3/i51.8GHzandbetter,

●graphicscardwithHDMIoutput,

●RAM-Notlessthan8GB,

●3 USB-ports.

Preparingforwork

Packagecontents

RаngeVisiоn3Dscannerissuppliedinaprotectedroadhardcase.Cameratripodis

placedinaseparatebag.

Thescannerisequippedwiththreescanningareas.Scanningareaisacalibrationplate

andstandforthecalibrationplate.

№

Name

qty.

Scanning module:

Installation construction with projector

Cable kit for connection to a PC (2 USB + HDMI)

Machine vision camera

Tripod

Calibration plate

Kit of optics

Stand for the calibration plate

USB disk with the software

License dongle

Power Cord 5 m

USB hub

Hex key

Rotary table + cables

Installingsoftwareanddrivers

Get the RаngeVisiоn software (equipped with the scanner) and run the installer -

RаngeVisiоn SсаnCenter setup.

Followingtheprompts,selectthedesiredlanguage,typeandpathforinstallation.

Aftertheﬁleshavebeencopiedinstalldriversandgraphicslibraries,necessaryfor

thecorrectoperationofRangeVision3Dscanner.

If you have access to the Internet RangeVision ScanCenter NG will automatically notify

you when updates are available. You can check for updates manually by clicking

About → Check for Updates.

Settingupyourcomputerforworkwiththe scanner

ForthecorrectoperationofRаngevisiоn3Dscanneryouwillneedtosetupyour

computer. Thisprocedureisperformedoncebeforetheﬁrstuseofthescanner.

Connectingprojector

TurnontheprojectorandconnectittotheHDMI-portofyourvideocard.After

connecting the projector,itshouldbedisplayedinthesystem.Ifthecomputer has

several videooutputs,deﬁnetheonetobeused.

1. Right click on the desktop, select Screen resolution,

2. Makesurethattheprojectorhasbeensuccessfullyrecognizedbythesystem

andthatbothconnectedscreensaredisplayed.

Conﬁguringcomputerparameters

Toavoidarecurrenceoftheproblemsduringthescanneroperation,youmustturn off

the screensaverandsleepmode.

Byclickingrightmousebuttononthedesktop,selectPersonalize→Screensaver and

turn off thescreensaver,disableturningoffthedisplayandputtingthe computer in sleep

mode.

ScannerAssembly

1. Mountthecamerasonthescanningmodule.

2. Installthescanningmoduleontripod.

3. ConnecttheprojectorwithHDMIcable.

4. ConnectcameraswithUSBcables.

5. Connectpowersupplyandturnontheprojector.

*old color variant with identical speciﬁcations is pictured

Otros manuales para SPECTRUM

Tabla de contenidos

Otros manuales de Escáner de Rangevision

Rangevision

Rangevision NEO Manual de uso y cuidado

Rangevision

Rangevision Smart Manual de usuario

Rangevision

Rangevision NEO Manual de uso y cuidado

Rangevision

Rangevision Smart Guía de solución de problemas

Rangevision

Rangevision Standard Plus Manual de usuario

Rangevision

Rangevision SMART ScanCenter 2016.2 Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario