R&S VTE Manual de usuario

R&S®VTE

Video Tester

Getting Started

Version 07

2116127002

(E@<Ô2)

This manual describes the R&S®VTE (2115.7300.02).

The software contained in this product uses several valuable open source software packages. For infor-

mation, see the "Open Source Acknowledgment" document, which is available for download from the

R&S VTE product page at www.rohde-schwarz.com/product/vte.html > "Downloads" > "Firmware".

Rohde & Schwarz would like to thank the open source community for their valuable contribution to embed-

ded computing.

Mühldorfstr. 15, 81671 München, Germany

Phone: +49 89 41 29 - 0

Email: [email protected]

Internet: www.rohde-schwarz.com

Subject to change – Data without tolerance limits is not binding.

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

Trade names are trademarks of the owners.

2116.1270.02 | Version 07 | R&S®VTE

Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g.

R&S®VTE is indicated as R&S VTE.

Contents

R&S®VTE

3Getting Started 2116.1270.02 ─ 07

Contents

1 Safety and Regulatory Information...................................... 7

1.1 Safety Instructions................................................................................7

1.2 Labels on the Product........................................................................ 10

1.3 Warning Messages in the Documentation........................................ 11

1.4 Korea Certification Class A................................................................11

2 Documentation Overview....................................................13

2.1 Getting Started Manual.......................................................................13

2.2 User Manuals and Help...................................................................... 13

2.3 Tutorials............................................................................................... 13

2.4 Printed Safety Instructions................................................................ 14

2.5 Data Sheets and Brochures............................................................... 14

2.6 Release Notes and Open Source Acknowledgment (OSA).............14

2.7 Application Notes, Application Cards, White Papers, etc...............14

3 Key Features........................................................................ 15

4 Preparing for Use.................................................................17

4.1 Lifting and Carrying............................................................................17

4.2 Unpacking and Checking................................................................... 17

4.3 Choosing the Operating Site............................................................. 18

4.3.1 Setting Up the Product..........................................................................18

4.4 Considerations for Test Setup...........................................................20

4.5 Connecting to Power.......................................................................... 21

4.6 Connecting External USB Devices....................................................21

4.6.1 External Keyboard................................................................................ 22

4.6.2 Mouse................................................................................................... 23

Contents

R&S®VTE

4Getting Started 2116.1270.02 ─ 07

4.6.3 Memory Stick........................................................................................ 23

4.6.4 External Drive....................................................................................... 23

4.7 Switching On or Off............................................................................ 23

4.8 Checking the Provided Options........................................................ 25

4.9 Turn-On Tests...................................................................................... 25

5 Instrument Tour................................................................... 27

5.1 Front Panel.......................................................................................... 27

5.1.1 Standby Key..........................................................................................28

5.1.2 Cursor Keys.......................................................................................... 29

5.1.3 ENTER/ESC Keys................................................................................ 29

5.1.4 Rotary Knob.......................................................................................... 30

5.1.5 Display.................................................................................................. 30

5.1.6 USB Interfaces......................................................................................30

5.1.7 Headphones..........................................................................................30

5.2 Rear Panel........................................................................................... 31

5.2.1 AC Power Supply Connector and Switch..............................................31

5.2.2 TRIGGER Input.....................................................................................32

5.2.3 MARKER Output...................................................................................32

5.2.4 EXT REF IN.......................................................................................... 32

5.2.5 REF OUT.............................................................................................. 33

5.2.6 DISPLAY PORT.................................................................................... 33

5.2.7 DVI Port................................................................................................ 33

5.2.8 LAN....................................................................................................... 34

5.2.9 USB Interfaces......................................................................................34

5.2.10 USB DEVICE Port.................................................................................35

5.2.11 eSATA Interface.................................................................................... 35

5.2.12 HDMI Connector................................................................................... 35

Contents

R&S®VTE

5Getting Started 2116.1270.02 ─ 07

6 Operating the R&S VTE in a LAN....................................... 37

6.1 Connecting the R&S VTE to a Network.............................................37

6.2 Connecting the R&S VTE to a Computer..........................................38

6.2.1 Windows 7 Operating System...............................................................38

6.2.2 Other Operating Systems..................................................................... 39

6.3 Zero Configuration Networking......................................................... 39

6.4 Configuring the Network Card...........................................................39

6.5 Firewall Settings................................................................................. 41

7 Installed Software................................................................ 43

7.1 Operating System............................................................................... 43

7.1.1 Login..................................................................................................... 43

7.1.2 Windows 7 Start Menu..........................................................................44

7.2 Additional Software............................................................................ 44

7.3 Backup and Restore Application.......................................................44

7.3.1 Creating a Backup................................................................................ 46

7.3.2 Restoring a Selected Backup Version...................................................47

7.3.3 Deleting a Backup.................................................................................48

8 Contacting Customer Support........................................... 49

Index..................................................................................... 51

Contents

R&S®VTE

6Getting Started 2116.1270.02 ─ 07

Safety and Regulatory Information

R&S®VTE

7Getting Started 2116.1270.02 ─ 07

1 Safety and Regulatory Information

The product documentation helps you use the product safely and efficiently. Fol-

low the instructions provided here and in the Chapter 1.1, "Safety Instructions",

on page 7.

Intended use

The product is intended for the development, production and verification of elec-

tronic components and devices in industrial, administrative, and laboratory envi-

ronments. Use the product only for its designated purpose. Observe the operating

conditions and performance limits stated in the data sheet.

Where do I find safety information?

Safety information is part of the product documentation. It warns you of potential

dangers and gives instructions on how to prevent personal injury or damage

caused by dangerous situations. Safety information is provided as follows:

●In Chapter 1.1, "Safety Instructions", on page 7. The same information is

provided in many languages as printed "Safety Instructions". The printed

"Safety Instructions" are delivered with the product.

●Throughout the documentation, safety instructions are provided when you

need to take care during setup or operation.

1.1 Safety Instructions

Products from the Rohde & Schwarz group of companies are manufactured

according to the highest technical standards. To use the products safely, follow

the instructions provided here and in the product documentation. Keep the prod-

uct documentation nearby and offer it to other users.

Use the product only for its intended use and within its performance limits. Inten-

ded use and limits are described in the product documentation such as the data

sheet, manuals and the printed safety instructions. If you are unsure about the

appropriate use, contact Rohde & Schwarz customer service.

Using the product requires specialists or specially trained personnel. These users

also need sound knowledge of at least one of the languages in which the user

interfaces and the product documentation are available.

Safety Instructions

Safety and Regulatory Information

R&S®VTE

8Getting Started 2116.1270.02 ─ 07

If any part of the product is damaged or broken, stop using the product. Never

open the casing of the product. Only service personnel authorized by

Rohde & Schwarz are allowed to repair the product. Contact Rohde & Schwarz

customer service at http://www.customersupport.rohde-schwarz.com.

Lifting and carrying the product

The maximum weight of the product is provided in the data sheet. To move the

product safely, you can use lifting or transporting equipment such as lift trucks

and forklifts. Follow the instructions provided by the equipment manufacturer.

Choosing the operating site

Only use the product indoors. The product casing is not waterproof. Water that

enters can electrically connect the casing with live parts, which can lead to elec-

tric shock, serious personal injury or death if you touch the casing. If

Rohde & Schwarz provides a carrying bag designed for your product, you can

use the product outdoors.

Unless otherwise specified, you can operate the product up to an altitude of

2000 m above sea level. The product is suitable for pollution degree 2 environ-

ments where nonconductive contamination can occur. For more information on

environmental conditions such as ambient temperature and humidity, see the

data sheet.

Setting up the product

Always place the product on a stable, flat and level surface with the bottom of the

product facing down. If the product is designed for different positions, secure the

product so that it cannot fall over.

If the product has foldable feet, always fold the feet completely in or out to ensure

stability. The feet can collapse if they are not folded out completely or if the prod-

uct is moved without lifting it. The foldable feet are designed to carry the weight of

the product, but not an extra load.

If stacking is possible, keep in mind that a stack of products can fall over and

cause injury.

If you mount products in a rack, ensure that the rack has sufficient load capacity

and stability. Observe the specifications of the rack manufacturer. Always install

the products from the bottom shelf to the top shelf so that the rack stands

securely. Secure the product so that it cannot fall off the rack.

Safety Instructions

Safety and Regulatory Information

R&S®VTE

9Getting Started 2116.1270.02 ─ 07

Connecting to power

The product is an overvoltage category II product and has to be connected to a

fixed installation used to supply energy-consuming equipment such as household

appliances and similar loads. Be aware that electrically powered products have

risks, such as electric shock, fire, personal injury or even death.

Take the following measures for your safety:

●Before switching on the product, ensure that the voltage and frequency indica-

ted on the product match the available power source. If the power adapter

does not adjust automatically, set the correct value and check the rating of the

fuse.

●If a product has an exchangeable fuse, its type and characteristics are indica-

ted next to the fuse holder. Before changing the fuse, switch off the instrument

and disconnect it from the power source. How to change the fuse is described

in the product documentation.

●Only use the power cable delivered with the product. It complies with country-

specific safety requirements. Only insert the plug into an outlet with protective

conductor terminal.

●Only use intact cables and route them carefully so that they cannot be dam-

aged. Check the power cables regularly to ensure that they are undamaged.

Also ensure that nobody can trip over loose cables.

●If the product needs an external power supply, use the power supply that is

delivered with the product or that is recommended in the product documenta-

tion or a power supply that conforms to the country-specific regulations.

●Only connect the product to a power source with a fuse protection of maxi-

mum 20 A.

●Ensure that you can disconnect the product from the power source at any

time. Pull the power plug to disconnect the product. The power plug must be

easily accessible. If the product is integrated into a system that does not meet

these requirements, provide an easily accessible circuit breaker at the system

level.

Cleaning the product

Use a dry, lint-free cloth to clean the product. When cleaning, keep in mind that

the casing is not waterproof. Do not use liquid cleaning agents.

Meaning of safety labels

Safety labels on the product warn against potential hazards.

Safety Instructions

Safety and Regulatory Information

R&S®VTE

10Getting Started 2116.1270.02 ─ 07

Potential hazard

Read the product documentation to avoid personal injury or product damage.

Electrical hazard

Indicates live parts. Risk of electric shock, fire, personal injury or even death.

Hot surface

Do not touch. Risk of skin burns. Risk of fire.

Protective conductor terminal

Connect this terminal to a grounded external conductor or to protective ground. This

protects you against electric shock should an electric problem occur.

Connecting headphones

Take the following measures to prevent hearing damage. Before using head-

phones, check the volume and reduce it if necessary. If you monitor varying sig-

nal levels, take off the headphones and wait until the signal has settled. Then

adjust the volume.

1.2 Labels on the Product

Labels on the casing inform about:

●Personal safety, see "Meaning of safety labels" on page 9.

●Product and environment safety, see Table 1-1.

●Identification of the product on the type plate.

Table 1-1: Labels regarding product and environment safety

Labeling in line with EN 50419 for disposal of electrical and electronic equipment after

the product has come to the end of its service life.

For more information, see the product user manual, chapter "Disposal".

Read the manual for information.

Headphone. Take care with the volume setting, see "Connecting headphones"

on page 10.

Labels on the Product

Este manual sirve para los siguientes modelos

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario