RadioLink TrackStar D-Spec TS4G Manual de usuario

Digital 4-Channel Proportional RC System

Instruction Manual

RadioLink Electronics Co., Ltd

Http://www.radiolink.com.cn

CE FCC ROHS

ＴｈｉｓｉｌｌｕｓｔｒａｔｉｏｎｉｓｆｏｒＲＣ４Ｇ＆ＲＣ３Ｓ

1. Introduction and service………………………………………………………….2

2. Safety guides……………………………………………………………….....…. 2

3. Battery recharge notice……………………………………………………..….…3

4. Contents and specifications………………………………………………..…..….4

5. Receiver installation and binding…………………………………………………5

8. Display when power switch turned on…………………………………….……... 8

9. Language Select "LANGUAGE"………………....……………………………......10

10. Model Select "MODEL"………………………………………………...................10

11. End Point Adjuster "EPA"………………………………….…..…..…………...…11

12. Steering EXP "STEXP"…………………………………….………..……………..12

13. Steering Speed "STSPD"……………………………………. .….…………..…... 13

14. Throttle EXP "THEXP"…………………………………………………………... 14

15. Throttle Speed "THSPD"………………………………………………………..... 16

16. A.B.S. Function "A.B.S"………………………………………………….............. 18

17. Throttle Acceleration "ACCEL"…………………………………………………. ..23

18. Idle-Up "IDLUP"…………………………………………………………........…. 2 4

19. Subtrim "SUBTR"…………………………………………………………..……. 2 5

20. Servo Reverse "REV"……………………………………………………….....…. 2 6

21. Steering Dual Rate/Throttle Dual Rate "D/R"………………………………...…… 27

22. ATL Function "ATL"………………………………………………………...…… 28

23. Programmable Mixes "PMIX"………………………………………………..….... 28

24. Channel 3 Position "AUX"………………………………………..…………… 31

25. Model name "NAME"…………………………………………………….….... 31

26.Low voltage alarm……………………………………………………...………. 32

29. Reset function "RESET"……………………………………………………...….. 34

Usage method of receiver intergrated with gyro and settings.......................................

6 .

ＳｃｈｅｍａｔｉｃｆｏｒｃｏｎｎｅｃｔｏｒｓｏｆＲ４ＥＨ－ＨａｎｄＲ４ＥＨ－Ｇ

ＧｙｒｏＳｅｎｓｉｔｉｖｉｔｙ

Ｆａｉｌｓａｆｅ

27.

28.

………………………… 7

……………………………………………………………

……… …………………………………………………… ………

Thank you for choosing RadioLink RC system, if you are the first time to use

this type of products, please read this statement carefully and strictly in accordance

with the requirements of operation. You could refer to the Manual if you meet any

problems during the operation . Please well keep the manual after use because you

might have to use it again next time.

If you found any problems during the operation process, please refer to the

manual. If the problem still exists, you could contact our dealers to find out the way to

solve it. And you could also log on our website for service:

Http://www.radiolink.com.cn

Important Safety Notice：

The following two symbols will appear in this manual（please pay attention to

the paragraph with this two symbols labeled）：

Prohibition Testing and confirmation

Do not use in bad weather such as rainy or thundering to assure the safety of

you and others.

Forbid to use this product in the crowd and the place against national law!

You need to turn the throttle channel(ch3) and inch switch to the lowest

before you use. Then switch on the transmitter, finally connect the receiver.

Before using, please make sure the movements of servo are corresponding

with the direction of joystick. If inconsistent, please adjust them before using.

Safety guides

Introduction and Service

The sequence to shut down is that turn off the receiver power first, and then

shut down the transmitter. If the above operations are reverse, it might lead to

uncontrolled situation and cause accidents

The transmitter needs to be powered by 4 AA alkaline 5# batteries or Ni-MH

batteries. Please check the voltage of batteries before using, as it might lead to

uncontrolled situation and accidents when the voltage is lacked. So you must change

the battery or recharge them in time.

Recharge steps：

A. Install the batteries to transmitter with correct directions, and cover it.

B. Connect the charger to the main connector.

C. Connect the charger to the transmitter charging port.

D. Cut off the power supply immediately while recharging completed.

Warning: Don’t try to charge to one-off dry batteries, avoiding a fire, explosion or

other severe consequence.

If you are using a nickel-cadmium, nickel-metal hydride batteries for recharging,

please use our company dedicated charger(optional accessory). If the electrical

current is too large and it might lead to overheated and cause a burning accident.

Please cut off the power supply immediately after recharging. Please take out the

batteries from the transmitter when you are not using it within a period, because the

battery might damage the battery connection metal flake, thus cause bad connection.

Above safety notices must be complied strictly, our company will not be

responsible for any damage caused by the behaviors forbidden in above notices.

Battery recharge notice

106mm

4.6-10

Contents and Specifications：

Contents：

1.Antenna 2.Binding key

3.Channel connection pin

Specs：

Size：51.5*24*15（mm）

Channel number：4 channels

Power standard：V

Frequency：2.4GHz Weight：5g

Contents：

1. Antenna

2. LCD

3. Menu key

4. Turning wheel

5. Function key A throttle

6. Function key B Direction

7. Function key C the 3rd channel

8. The 3rd/4rd channel VR

9. The 3rd/4rd channel button

10. Recharge connection slot

11. Throttle trigger

12.Simulator port

13.Power switch

14. USB hardware upgrade port

Specs：

Size：213*117*115.5(mm)

Antenna length：

Weight：420g

Channel number：4 channels

LCD：128*64 lattice（with backlight）

Contents and specifications

range,

Power standard：6VDC (1.5AA*4)

RF power：less than 10dbm

Power extending: JST port 2S~3S

LiPo/LiFePo battery

Modulation: FHSS

Low voltage alert：Yes（lower than 4.6V）

Data resolution：2048

Frequency：2.4GHz

RF range: 300meters on ground

Failsafe: in 1 second receiver fail getting signal from TX, the throttle will be 0, servos

keep the last status.

Receiver’s connection and installation：（such as some car model）

Rudder Servo(CH1)

Throttle

Servo(CH2)

Servo(CH3)

Servo(CH4)

NOTICE：

1．Confirm battery, switch, servos and etc are connected with receiver right.

2．While installing servos, please keep servo’s distance from model body,

otherwise the vibration can lead to servo and make servo damaged.

3．After installation of servos, please try to control the servo to full if it

got stuck or sounded abnormal, you must solve the problem. Even if servo

Receiver installation and binding

* RC3S standard equipment:A transmitter and a R4EH-H receiver.

* RC4G standard equipment:A transmitter and a R4EH-G receiver.

was not damaged, large circuit occurred.

4．Do not cut off or bind the receiver antenna, and try the best to keep it

far

away from metal and carbon graphite material.

5．Receiver is made up from precise electronic components, it need to

protected from vibration by packaged with sponge or other shock

absorption materials.

Schematic for connectors of R4EH-H

Schematic for connectors of R4EH-G

Code-matching method between transmitter and receiver:

1．Load the battery into transmitter, power on it.

2．Connect the power to the 2nd Channel pin of receiver.

3．Press the binding button on the receiver till LED starts twinkling.

4．LED stops the twinkle, bright light indicates a successful

code-matching was completed.

Display when

power

R4EH-G is intergrated with gyro,it can make cars run stablely,

the effect is more obvious

when the car is turning.

The gyro function can be set "ON"and "OFF"

Description of indicator light:

1.Receiver in normal working condition:Green light on

2.Gyro in working normal condition:Red light on

Attention:The gyro function was set to on by factory.

When the receiver is in working condition

At this time,

the red light flashing,the gyro enter a self-examination state.

please keep the

receiver in a stable condition.

In normal condition, the direction of cars including forward and backward.

Method of using receiver intergrated with gyro

The gyro should

only work in forward direction.

only when choosing the correct direction,can the gyro really work.

Attention:The vehicle gyro has the phase adjusting function,

Gyro function settings:

1.Usage method of gyro:Short press the code key for three times(time interval

between

each time lasts less than 1 second ), the red light continuous flashing three times, then

the red light into a lasting bright, it shows the gyro in a normal state.

2.The gyro sensitivity:The default is three channel.

The VR switch can be used for real-

time adjustment when the radio control works,to ensure that the third channel VR

control

(Factory default)

clockwise, the sensitivity increases, counterclocwise, the sensitivity decreases.

Attention:Sensitivity shuoldn't be set to 0.

powered

button twice, the

phase correction is completed.

press code

In this situation, short

When to the right,wheel left correction.

When rotating the car to the left,wheel

to observe whether the gyro is correcting wheel.

turn around the car

forward direction. , then the

code button for once(less than 1 second),

, then gyro works in backward direction.

engine doesn't move

release the accelerator

the

3.Gyro usage method in forward and backward direction:

When gyro in working state, pull

remote acceleraterto keep the car move forward for a distance,

in the premise of not playing the direction key,

turn around the

car body,

You need

the right light flashes once

4.Gyro phase adjustment:When the gyro works in forward direction,

if the steering

to short press the

gyro works in

Receiver

Battery

voltage

Model name

display R/C

control

system name

Steering trim display

Throttle trim display

Display when power switch turned on

LCD Screen

When you power on the transmitter, LCD screen shows

battery

voltage,

R/C

control

system

name, model name,

steering

trim,throttle trim

Model Name

can store the data for 10 models, model name will show on the LCD when

you power on the transmitter. Please make sure the model name the screen displayed

is the right what you want. If the model name you chose is not corresponding with

your model, the pre-settings should be wrong.

Transmitter battery voltage

In addition to the model#, LCD can show the voltage of battery. When the

voltage is lower than 4.6V, it would start the low-voltage alert, it would send out

“BeBe…” sounds, till the transmitter is power-off. When you hear the low-voltage

alert, you have no more than 4 minutes for controlling your model, please safely stop

your model before the uncontrolled situation. Please make sure the battery voltage is

higher than this voltage data while radio controlling.

Transmitter function menu setting

When you want to browse or change a setting of transmitter, you should go into

function menu setting mode. Under function menu setting mode, you can set up

Language Select "LANGUAGE", Model Select "MODEL",End Point Adjuster "EPA",

Steering EXP "STEXP",Steering Speed "STSPD",Throttle EXP "THEXP",Throttle

Speed "THSPD",A.B.S. Function "A.B.S",Throttle Acceleration "ACCEL",Idle-Up

"IDLUP",Subtrim "SUBTR",Servo Reverse "REV",Steering Dual Rate/Second

Dual Rate "D/R",ATL Function "ATL",Programmable Mixes "PMIX", Auxiliary

Channel 3 and 4 "AUX"，Model name "NAME", Reset function "RESET".

,the red light flashes two times

The system

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mando a distancia de RadioLink

RadioLink

RadioLink RC4GS V3 Manual de usuario

RadioLink

RadioLink T8S(BT) Manual de usuario

RadioLink

RadioLink AT9 Manual de usuario

RadioLink

RadioLink T8S Manual de usuario

RadioLink

RadioLink RC4GS V3 Manual de usuario

RadioLink

RadioLink T4EU Manual de usuario

RadioLink

RadioLink T8S Manual de usuario

RadioLink

RadioLink T6EAP Manual de usuario

RadioLink

RadioLink T8S(BT) Manual de usuario

RadioLink

RadioLink Ei411H Manual de usuario

RadioLink

RadioLink AT10 Manual de usuario

RadioLink

RadioLink RL036T-001A Manual de usuario

RadioLink

RadioLink t8fb Manual de usuario

RadioLink

RadioLink RC4GS V2 Manual de usuario

RadioLink

RadioLink RC8X Manual de usuario

RadioLink

RadioLink t8fb Manual de usuario

RadioLink

RadioLink T8S Manual de usuario

RadioLink

RadioLink T8S Manual de usuario

RadioLink

RadioLink t8fb Manual de usuario

RadioLink

RadioLink RC6GS V2 Manual de usuario

RadioLink

RadioLink t8fb Manual de usuario

RadioLink

RadioLink AT10II Manual de usuario

RadioLink

RadioLink AT10II Manual de usuario

RadioLink

RadioLink T7F-2.4Ghz Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación