Radiocrafts RC2301DK Manual de usuario

Radiocrafts

EmbeddedWirelessSolutions RC2301DK

RC2301DK Demonstration Kit Quick Start

ZigBee®-ready Location Engine demo

Introduction

The RC2301DK demonstration kit shows a ZigBee®-ready location demo application on the

Figure 8 Wireless Z-stack from Texas Instruments. To make the demonstration a minimum of

8 nodes are required:

•One Location Dongle (D) configured as network coordinator

•Six reference nodes (R1 to R6) configured as network routers

•One blind node (B) with RC2301 configured as network router

The kit contains all 8 boards and each board has an identifier label on the reverse side.

Radiocrafts

EmbeddedWirelessSolutions RC2301DK

Quick Start Guide

1. Download location demo PC application

Download the latest verion of the location demo PC(Z-Location Engine) SW from TI (

http://www.ti.com/litv/zip/swrc070c ) and install it on your PC.

2. Set up the Location Dongle

Start the Z-location Engine program on the PC. Power up the Location Dongle and connect it

to a COM-port on your computer. Make sure the “Select COM port field at the bottom of the

application window correspond to the correct port. The program does not support USB-Com

port, only pure RS232 COM ports.

Press the “►” button in the application and observe that the application connects to the

dongle at the bottom of the application window.

Figure 1. Before connection

Figure 2. After connection

3. Add a background image

Select the Background tab in the application window. Select a Background Image and type in

the width and height. Displacement should be 0 if the image shall be placed in the top left

corner of the image window in the application.

Figure 3 Background tab

Press Update, and the picture should become visible in the application window.

Radiocrafts

EmbeddedWirelessSolutions RC2301DK

4. Power up reference nodes

Connect power to reference node 1 (R1). Make sure that it is in range of the location dongle.

The reference node will appear in the Reference Node Setup tab in the application, and will

also appear in the graphical window as a yellow ball.

Figure 4. Reference Node Setup tab

Double-click on the node in the list and change the location coordinates. Press update.

Status of the device will be updating. When the update is complete, double-click the node

again to make sure the updating was successful. Then place the node at the specified

location.

Repeat for nodes R2 to R6.

5. Activate blind node

Activate the blind node by connecting it to a battery. After a few seconds the blind node will

appear in the application window as a green ball.

6. Tuning the application

The application can be tuned by changing the parameters that the location engine in RC2301

uses. This is done in the Blind Node Setup tab. Double-click on the blind node you want to

change, set the parameters and press update. For a description of the parameters see the

Radiocrafts

EmbeddedWirelessSolutions RC2301DK

chapter on Blind Node Configuration in the Z-Stack Location Profile document by TI

(Document Number: F8W-2006-0002).

Some parameters of the application can also be tuned in the Settings window.

Contact Information

Radiocrafts AS

Sandakerveien 64

NO-0484 OSLO

NORWAY

www.radiocrafts.com

radiocrafts@radiocrafts.com

Tel: +47 4000 5195

Fax: +47 22 71 29 15

reserved.

Tabla de contenidos

Otros manuales de Placa madre de Radiocrafts

Radiocrafts

Radiocrafts RC188 DK Series Manual de usuario

Radiocrafts

Radiocrafts RC2300DK Manual de usuario

Radiocrafts

Radiocrafts RC1880DK Manual de usuario

Radiocrafts

Radiocrafts RC2200DK-HCL Manual de usuario

Radiocrafts

Radiocrafts RC2300DK Manual de usuario

Radiocrafts

Radiocrafts ZigBee RC2200DD Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario