Quick BTAC Series Manual de usuario

ELECTRIC THRUSTERS

USER MANUAL IT pag. 3

BTAC

series

DOUBLE PROPELLER

REV 000A

BTAC250200 •BTAC300300 • BTAC300350 •BTAC386420 •BTAC386460 • BTAC 5131000

3INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series EN

Index

1 - Information about the product Pag. 4

1.1 - Technical data Pag. 4

2 - Supplied parts Pag. 5

2.0 - Package contents Pag. 5

2.1 - Needed tools for installation Pag. 5

2.2 - “Quick®” recommended accessories Pag. 5

3 - Introduction Pag. 5

3.0 - Important notes Pag. 5

3.1 - Precautions for the installer Pag. 5

3.2 - Installation requirements Pag. 6

4 - Safety Pag. 6

4.0 - Warnings Pag. 6

5 - Installation Pag. 7

5.0 - Propellers Pag. 7

5.1 - Tunnel Pag. 8

5.2 - Thruster Pag. 9

5.3.0 - BTAC 250/300 gearleg and motor support ange Pag. 10

5.3.1 - BTAC 386 gearleg and motor support ange Pag. 11

5.3.2 - BTAC 513 gearleg and motor support ange Pag. 11

5.4.0 - BTAC 386 rilsan tube and oil tank Pag. 12

5.4.1 - BTAC 513 rilsan tube and oil tank Pag. 12

5.5 - Oil tank positioning Pag. 13

5.6 - BTAC 386/513 coupling/motor assembly Pag. 14

5.7 - Propellers tting Pag. 15

6 - Connection diagram Pag. 16

7 - Warnings Pag. 16

7.0 - Warnings Pag. 16

8 - Usage Pag. 17

9 - Maintenance Pag. 17

10 - Disposal of the product Pag. 17

11 - Spare parts Pag. 18

12 - Dimensions Pag. 21

4INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series

1 - Information about the product

MODELS BTAC386420 BTAC386460 BTAC513100

N° Propellers 2 contra-rotating NIBRAL 2 contra-rotating NIBRAL

Tunnel Ø

386 mm (15” 13/64)

513mm (20” 13/64)

Motor type Four-pole electric motor

Motor power 30 kW 37 kW 75 kW

Voltage 400/690 V 400/690 V 400/690 V

Thrust 420 kgf (925 lb) 460 kgf (1014 lb) 1000 kg (2205 lb)

Limit thickness values of

the tunnel

min. 8 mm - max 15 mm

(min. 5/16" - max 19/32")

min.12 - max 22 mm

(15/32" - 55/64")

Weight 304 kg (670.20 lb) 387 kg (853.19 lb) 742 kg (1636 lb)

MODELS BTAC250200 BTAC300300 BTAC300350

N° Propellers 2 contra-rotating PLASTIC 2 contra-rotating NIBRAL

Tunnel Ø

250 mm (9" 27/32) 300 mm (11" 13/16) 300 mm (11" 13/16)

Motor type Two-pole electric motor

Motor power 15 kW 15 kW 22 kW

Voltage 400/960 V 400/690 V 400/960 V

Thrust 200 kgf (441 lbs) 300 kgf (661 lbs) 350 kgf (771 lbs)

Limit thickness values of

the tunnel

min. 6,5 mm - max 11 mm

(min. 1/4" - max 7/16")

min. 9,5 mm - max 13,5 mm

(min. 3/8" - max 17/32")

Weight 160 kg (353 lb) 167 kg (368 lb) 216 kg (476 lb)

BEFORE USING THE THRUSTER, CAREFULLY READ THIS USER MANUAL.

IF IN DOUBT, CONTACT YOUR NEAREST QUICK®DEALER

QUICK® RESERVES THE RIGHT TO INTRODUCE CHANGES TO THE EQUIPMENT AND THE CONTENTS OF THIS MANUAL WITHOUT PRIOR NOTICE. IN CASE OF DISCREPANCIES OR

ERRORS BETWEEN THE TRANSLATED TEXT AND THE ORIGINAL ITALIAN TEXT, PLEASE REFER TO THE ITALIAN TEXT

1.0 - Technical data

5INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series EN

2 - Supplied parts

2.0 - Fornitura di serie e materiale incluso nella confezione

• AC Thrusters

• Drilling template

• Gasket

• O-ring (for assembly) - (only 250-300-513)

• User’s manual

• Conditions of warranty

2.1 - Needed tools for installation

BTAC 250 • Drill and drill bits Ø 11 mm (7/6”) • Hole saw Ø 46 mm (1” 13/16)

• Hex keys 4 mm, 5 mm, 8 mm e 10 mm • wrench 24 mm

BTAC 300 • Drill and drill bits Ø 15 mm (19/32”) • Hole saw Ø 53 mm (2” 3/32)

• Hex keys 4 mm, 5 mm, 8 mm e 12 mm • wrench 27 mm

BTAC 386 • Drill and drill bits Ø 16 mm (4" 5/8) • Hole saw Ø 120 mm (4" 23/32)

• Hex keys 4mm, 6mm 5 mm, 8 mm e 14 mm • wrench 27 mm

BTAC 513 • Drill and drill bits Ø 18 mm (45/64”) • Hole saw Ø 140 mm (5” 33/64)

• Hex keys 5 mm, 8 mm e 14 mm • wrench 32 mm

2.2 - Quick®recommended accessories

• TCD 1022 • AC POWER

• TCD 1062 • INVERTER

• TCD 1042 • AJ1

• TCD 1044 • PCS TJ1

• PCS TJ2

• PCS TJ3

• PCS DTW

3 - Introduction BTAC series

This document contains the instructions that are necessary for boat manufacturers and

marine equipment installers to assemble and commission the Thrusters.

Warning symbol concerning hazardous

situations.

Caution symbol to avoid direct or

indirect damage to the product.

This manual contains Warning and/or Caution symbols that are important for safety.

Comply with the recommendations provided herein.

3.0 Important notes

PROCEEDING WITH THE INSTALLATION IN GOOD LIGHT CONDITIONS.

We recommend using an appropriate personal protective equipment.

Quick®thrusters are not suitable for installation in potentially explosive environments and/or atmospheres.

Assembly and subsequent checks or repairs must only be carried out by qualied personnel.

3.1 Precautions for the installer

6INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series

3 - Introduction

4 - Safety BTAC series

3.2 - Installation requirements

It is strongly recommended to entrust a professional with the preparation and positioning of the tunnel in the hull.

These instructions are generic and do not show by any means the details of the operations of preparing the thruster, which

falls under the competence of the shipyard. In case of problems caused by a defective installation, the installer will be held

responsible.

Despite all components and moving mechanical parts are of high quality, the correct installation of the propulsion unit is funda-

mental for a safe and efcient use of the boat, as well as of the propulsion unit itself.

Please note that the installation of such unit is an operation requiring experience and technical competence. It is recommended

to entrust the installation to competent staff and to consult the manufacturer or naval architects to fully evaluate the entity

of the work.

THE PRODUCT MUST BE DISCONNECTED FROM THE HYDRAULIC SYSTEM BEFORE INSTALLING OR PROVIDING

MAINTENANCE.

Quick® takes no responsibility regarding the inadequate connection of the users to the hydraulic system

and to the safety of itself.

4.0 - Warnings

• Quick®Thrusters have been designed and constructed only for nautical use.

• Do not use these appliances for other uses.

• Quick®shall accept no responsibility for direct or indirect damages caused by improper use of the

appliance or an improper installation.

• The Thruster is not designed to maintain loads generated in particular atmospheric conditions (storms).

• We recommend that you entrust the preparation and the positioning of the tunnel on the hull to a skilled

professional.

• These are generic instructions and do not give details of the preparatory operations for installing the tunnel,

which falls under the competence of the boatyard. The installer shall bear full responsibility for any problems

caused by defective installation of the tunnel.

• Do not install the electric motor near easily inammable objects.

7INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series EN

5 - Installation

minimum 0,75 times the

tunnel Ø

BARYCENTER

L 1

L 2

A A

• The position of the tunnel will depend on the

interior and exterior shape of the boats bow.

• Optimal positioning of the tunnel will be in the

bow and as low as possible and at a distance

from the waterline which should be at least 0,75

times the tunnel diameter.

• To avoid cavitation in the propeller, the tunnel

must be positioned as low as possible in the

hull.

• The lever effect in the boat is proportional to

the increase of the distance (L1 and L2) between

the barycentre and the position of the tunnel A

and B.

• An increase in the length of the tunnel increases the effect of the loss of charge, decreasing the nominal driving force.

• For a correct use of the thruster we suggest a maximum length of 3-4 times the tunnel diameter and a minimum length of

1,5 times the tunnel diameter. To limit efciency loss it is acceptable a length that is six times the tunnel diameter.

FFor greater lever effect prefer position B

to position A.

5.0 - Propellers

MINIMUM 1,5 TIMES

TUNNEL Ø

MAXIMUM 6 TIMES

TUNNEL Ø

8INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series

5 - Installation

5.1 - Tunnel

• The rounded ends of the tunnel limit the creation of turbulences and cavitations, improving performance of the propeller

thrust and reducing noise levels to a minimum.

• The force produced by the ow of the water when the boat is moving produces resistance on the rear face of the tunnel,

which is an area exposed frontally to the water ow.

To limit this phenomenon, prepare an indentation in the rear part of the tunnel. Otherwise, create a deector on the front

part of the tunnel.

• If the tunnel is near the waterline, it is advisable to t a grating at the end of the tube.

The grating must have vertical and as large as possible meshes to avoid contrasting the

propeller thrust.

The vertical meshes prevent the entry of most of the oating objects.

9INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series EN

10 2 3 4 5 6 7 8 9 10

Fig. D Fig. E

Fig. F

BTAC 250/300 BTAC 386 BTAC 513

5 - Installation

5.2 - Thruster

SUPPORT

TUNNEL

HULL

Fig. A Fig. B

SUPPORT TUNNEL

Fig. C

• It is recommended to install the thruster with a support base; the motor is already equipped with support feet.

• FIG.A The AC motor must be installed on a separate support from the hull. The support must be dimensioned so as to with-

stand the weight and power specied (table on page 4).

• FIG.B The distance (D) between the tunnel centerline (gure B) and the motor support must allow correct alignment between

the drive axle and the gearbox shaft.

• FIG.C The angle between the two shafts (gearbox and engine) must not exceed +/- 1.5 degrees.

• To position the thruster in the tube, nd the halfway

point. Fig.D

• Use the ange to mark the centre of the holes on

the tube. Fig.E

• Fix the drilling template on the reference points, making su-

re they are aligned with precision at the half-way point of the

tube. FIG.F

N.B. All holes must be exactly aligned with the half-way

point of the tunnel, since tolerance between propeller

and tunnel is minimal.

• Take care that there are no resin residues in the contact

area between ange and tube; this could cause misalignment.

Any resin residues and any other hindrance to correct contact

must be removed by sandpaper.

10 INSTALLATION AND USE MANUAL BTAC SERIES - REV000A

BTAC Series

5 - Installation

Fig.G

• Insert two o-rings into the special

seats inside the ange.

Fig.G BTAC 250/300

5.3.0 - BTAC 250/300 Gearleg and motor support flange

SILICONE

• Proceed with tting the gearleg with

the special seal gasket.

• For further protection against the entry

of water, apply silicone for nautical

use around the point of contact between

ange and tube.

• Fasten everything to the ange using

the special screws.

• Grease the terminal part of the gearleg shaft; fit the

small key into its seat.

• Insert the elastic joint in the terminal part of the

gearleg shaft.

• Insert the motor onto the elastic joint. Secure with

four screws and four washers.

• Grease the terminal part of the gearleg shaft.

Otros manuales para BTAC Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Motor fuera de borda de otras marcas

Yamaha

Yamaha VF150 Manual de usuario

Sleipner

Sleipner SEP-IP30 Manual de usuario

Suzuki

Suzuki DF 40 Manual de usuario

SELVA MARINE

SELVA MARINE Corse Manual de usuario

TOHATSU

TOHATSU BFT 250A Manual de usuario

KONRAD

KONRAD Series 600B Manual de usuario

Mercury

Mercury 8 Bigfoot 4-Stroke Guía de instalación

Sleipner

Sleipner E-Vision Electric Thruster E300 Manual de usuario

Suzuki

Suzuki DF40A Manual de usuario

IST

IST 18.BF200D Manual de usuario

Side-Power

Side-Power SP 155 TC i Manual de usuario

Mercury

Mercury 40 FourStroke Manual de usuario

Yamaha

Yamaha VF90 Manual de usuario

Yamaha

Yamaha D150H Manual de usuario

Yanmar

Yanmar ZT350 series Manual de usuario

MotorGuide

MotorGuide X3-40 Manual de usuario

Mercury

Mercury 30 - 60 HP Manual de usuario

Yamaha

Yamaha 20D Manual de usuario