Quasar SQ3202 Manual de usuario
32” HD LED TV
SQ3202
AIR/CABLE MODE SELECTION
The Air/Cable menu option is set to the “Air” mode at the factory so that you
can receive the over-the-air broadcast signal. If you want to receive the Cable
TV signal through the antenna input terminal, this menu option must be switch
to the “Cable” (Cable TV) mode. Please refer to page 14 of this manual for the
details of the menu.
INSTRUCTION MANUAL
Contents
zIntroduction
zWarning
zCaution
zMain Unit Description
zRemote Control
zOSD Basic Adjustment
zSpecifications
zTroubleshooting
1
Introduction
INSTALLATION
Locate the receiver in the room where direct light does not strike the screen.
Total darkness or a reflection on the picture screen can cause eyestrain.
Soft and indirect lighting is recommended for comfortable viewing.
Allow enough space between the receiver and the wall to permit ventilation.
Avoid excessively warm locations to prevent possible damage to the cabinet or
premature component failure.
This TV can be connected to AC 100-240V~ 50/60HZ.
Do not install the TV in a location near heat sources such as radiators, air ducts,
direct sunlight, or in closed compartments and closed areas.
Do not cover the ventilation openings when using the TV.
The indicator light will last for about 30 seconds after the power has been turned
off.
Wait until the indicator light goes out before repowering the TV.
Thank you for purchasing QUASAR HD LED Television. To get the most out of your
new purchase, it is highly recommended that you read this manual before starting the
operation.
2
Warning
This symbol is intended to alert the user to avoid the risk
of electric shock. This equipment may only be disassembled
by qualified service personnel.
This symbol is intended to alert the user to the presence
of important operation and maintenance instructions in
the literature accompanying the equipment.
Class I structures of equipment should be connected to the grid
power output with a protective earth connection on the socket.
Power plug as a broken applianceˈbroken installations should
be easy to operate.
CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
3
Caution
Caution
High voltages are used in the operation of this product.
Do not open the product's casing. Refer servicing to qualified
service personnel .
Caution
To prevent fire or electrical shock hazard, do not expose the main
unit to rain or moistureˈdo not place objects filled with liquids,
such as vases, on the apparatus.
Caution
Do not drop or push objects into the television cabinet slots or
openings. Never spill any kind of liquid on the television
receiver.
Caution
Avoid exposing the main unit to direct sunlight and other sources
of heat. Do not stand the television receiver irectly on other
products which give off heat: e. g. video cassette players and
audio amplifiers. Do not block the ventilation holes in the back
cover. Ventilation is essential to prevent failure of electrical
components. Do not squash the power supply cord under the
main unit or other heavy objects.
4
Caution
Caution
Never stand on, lean on or suddenly push the product or its stand.
You should pay special attention to children.
Caution
Do not place the main unit on an unstable cart stand,
shelf or table. Serious injury to an individual and
damage to the television may result if it should fall.
Caution
When the product is not used for an extended period of time, it is
advisable to disconnect the AC power from the AC outlet.
Caution
The LED panel used in this product is made of glass and is therefore
breakable. This product must not be dropped or banged. If the LED
Panel breaks be careful of being injured by broken glass.
5
Main unit description
Control Panel Button Function
TV Terminal Connections
1. HEADPHONE out terminal.
2. Coaxial out terminal.
3. Audio input terminal for component video/composite video.
4. Component video/composite video input terminal.
5. HDMI1 input terminal.
6. HDMI2 input terminal.
7. HDMI3 input terminal
8. VGA input terminal of simulation signal of PC.
9. PC AUDIO input terminal.
10. RF antenna.
11. USB input terminal˄Playing JPEG files.˅
VOL+ : Volume up.
VOL- : Volume down.
CH+ : TV channel up.
CH- : TV channel down.
MENU : Press to select the main menu.
SOURCE : Select the input sources.
POWER : Switching Power On/Standby.
6
Remote control
POWER: Power on/off button, press once to turn the TV on and press
again to turn the TV off.
MUTE: Press this button to mute or restore sound.
MTS: In the TV condition, press this key to select the stereo mode.
ASPECT: Press to adjust picture ratio.
PICTURE: Select picture mode.
SOUND: Select sound mode.
0-9: Select and switch to a channel using 0 - 9.
-/--: Switch the program digit.
: Switch back and front between the current and previous channels.
AUTO: Adjust the picture automatically in pc mode.
EPG Enter electronic program guide
FAV: Switch between custom set "Favorite List"
RED, GREEN, YELLOW, CYAN: This button is not available.
SLEEP: Set the sleep timer.
SOURCE: Press to change signal source.
ENTER: Enter the selected option or perform the selected operation.
MENU: Press this button to enter the main menu.
EXIT: Exit the OSD (On-screen display).
CH+/CH-: Change the channel.
CC: Press this key to select the CC ,ON or OFF mode
DISPLAY: Display TV information.
VOL+/VOL-: Adjust the volume.
PICTURE
SOUND
AUTO
Quasar
Quasar
Instruction for Wall Mount
200mm x 200mm
4
8
Installation Guide
Press MENU button to display the MAIN OSD MENU; Press / button to select the
MENU you want; Press ENTER button to enter the sub menu; Press / button to select the
option and then press / to adjust the value in the sub menu; You can press MENU button to
go backto the upper menu or EXIT button to close the OSD.
PICTURE
You can select the type of picture, which best corresponds to your viewing. Press the “MENU”
button to enter the OSD menu .Then press
“e/f” button to select the “PICTURE”
menu.
1. Press “d” button to select “Picture
Mode”, press “e/f” button to select.
2. Press “c/d” button to select
“Brightness” and press the “e/f”
button to enter brightness adjustment
menu to adjust brightness.
3. Press “c/d” button to select
“Contrast” and press the “e/f” button
to enter contrast adjustment menu to adjust contrast.
4. Press “c/d” button to select “Color” and press the “e/f” button to enter color adjustment
menu to adjust color.
5. Press “c/d” button to select “Tint” and press the “e/f” button to enter hue adjustment menu
to adjust tint.
Note: The 'Tint' item is used in NTSC mode only.
6. Press “c/d” button to select “Sharpness” and press the “e/f” button to enter sharpness
adjustment menu to adjust
sharpness.
7. Press “c/d” button to select
“Color Temperature” and press the
“e/f” button to select.
8. Press “c/d” button to select
“Advanced Setting” and press the
“ENTER/f” button to enter
sub-menu.
a. Press “c/d” button to select
Tabla de contenidos
Idiomas:
Otros manuales de TELEVISOR de Quasar
Quasar
Quasar SP-2721 Manual de usuario
Quasar
Quasar SP-2021D Manual de usuario
Quasar
Quasar SP-2729UV Manual de usuario
Quasar
Quasar SQ4800 Manual de usuario
Quasar
Quasar SP-2022D Manual de usuario
Quasar
Quasar SR-5133 Manual de usuario
Quasar
Quasar SP-2019D Manual de usuario
Quasar
Quasar SP-2725F Manual de usuario
Quasar
Quasar SR5143B - 51" PROJECTION TV Manual de usuario
Quasar
Quasar SQ3204 Manual de usuario
Manuales populares de TELEVISOR de otras marcas
Philips
Philips Colour Television Manual de usuario
Toshiba
Toshiba 27A10 Manual de usuario
Philips
Philips 42PF9630A/37 Manual de usuario
Hitachi
Hitachi 32FX48B Manual de usuario
DAEWOO ELECTRONICS
DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario
Changhong Electric
Changhong Electric uhd55b6000is Manual de usuario
