Quanturi HAYTECH Manual de usuario

Temperature monitoring system

with base staon QNT300-10

User manual

Manuel d‘ulisaon

Gebrauchsanweisung

HAYTECH

Tango M

Tango XN

In case of problems please

contact:

[email protected]

Find more instrucons at:

www.quanturi.com/resources

Support

transmion or transcripon of this

manual are not permied without

Quanturi's prior consent. Quanturi

reserves the right to change the content

of this manual at any me and without

prior noce.

Content

English 4

Base staon 6

Troubleshoong 8

HAYTECH probes 10

Tango and Tango XN probes 13

Français 16

Lecteur 18

Problèmes techniques 20

Sondes HAYTECH 22

Sondes Tango et Tango XN 25

Deutsch 28

Basisstaon 30

Problembehebung 32

HAYTECH Sensoren 34

Tango und Tango XN Sensoren 37

English

User Manual

Usage and precauons

The User is expected to thoroughly familiarize themselves with the

HAYTECH system usage instrucons, and then use the product with

care and diligence.

The User's installaon of the HAYTECH system is not to replace the

normal usage and safety precauons that the User should connue

to take to avoid a re breaking out. The HAYTECH system acts as an

addional tool to safeguard hay, but under no circumstances should

it be used as the sole surveillance system. Quanturi cannot be held

responsible for a re breaking out nor for any of the consequences of

this.

The User undertakes to regularly check that the whole HAYTECH

system works properly, and to take all necessary precauons with

respect to the material’s upkeep.

The HAYTECH monitoring system is used for wireless temperature

monitoring of square and round bales during the storage period.

The HAYTECH monitoring system is composed of temperature probes,

a base staon and repeater(s). The temperature probes are placed

inside the bales before storage. When taking a bale out of the storage

for use, the probe should be removed and stored for the next cut or

the next season. The repeater is used to transmit the temperature

values from the probes to the base staon. The base staon sends the

measurement data to Quanturi.app.

This manual walks you through the installaon and setup procedure.

Aer going through all the steps in this manual, the HAYTECH

monitoring system is ready for use.

The User hereby notes that each temperature probe is to be used to

measure the temperature of only one single hay bale, and may not be

used to measure several enes.

Furthermore, the User undertakes to remove the temperature probes

from the hay bales before they are used for any purpose other than

conservaon.

Quanturi may not under any circumstances be held liable for any

damages arising from the User's negligent use of the material whether

this be directly or indirectly, including – but not limited to – loss of

prots, loss of savings or any other damages or expense.

For more informaon about the terms of use, please visit:

hps://quanturi.com/pages/terms



200 m

50 m

3 Mount the base staon

vercally and do not mount the

it on a metallic surface. Keep the

base staon at least 10 cm away

from any solid metal objects.

2 Mount the base staon at

a minimum height of 2 meters,

so that no major obstacles are

in between it and the sensor

probes.

Do not mount the base staon

directly above the probes.

Base staon

1 The base staon

communicates wirelessly with

the temperature probes in the

storage. The distance between

the probes and the base staon

is ideally less than 50 meters.

200 m



200 m

50 m

3 Create an account by

specifying your username,

password, company, address,

and phone number. You will

receive an SMS to conrm your

phone number. Alerts will be

sent to this phone number.

4 Upon your rst login, you will

be promted to add your probes

to the system, using code 2 from

your probe package.

1 Go to the web address:

www.quanturi.app/acvaon

to start the acvaon.

2 Acvate your system by

entering code 1 from your base

staon package.

Acvaon

QNT100-00

CODE-1234

EFGH-5678

HAYTECH System 10

www.quanturi.app/activation

Activation code 2 / Code d’activation 2

PRODUCT STICKER

ACTIVATION STICKER

PROBE ID X00001, X000002, X000003, X000004,

X000005, X000006, X000007, X000008, X000009,

X000010

BS ID X0000001

MADE IN FINLAND

PAP

2 m



200 m 200 m



200 m

Indicator Lights

79°C

74°C

68°C

62°C

55°C

49°C

45°C

38°C

TemperatureID

1321

1232

1234

2223

1112

2333

2096

2124

2243

220V

NETWORK

ADAPTER



2 m



The DATA indicator is on, when the base staon has stored new data

to be sent to the Quanturi server. The indicator light is blinking when

the base staon is receiving data from the sensors.

DATA

4 Connect the base staon

with the included power supply

to an electrical outlet.

220V

ADAPTER

200 m

min. 2 m



5 Wait for the base staon to

inialize. Aer a few minutes the

NETWORK light in the middle

turns on. It indicates that the

base staon is connected to the

network and operaonal.

220V

ADAPTER

200 m

min. 2 m



6The temperature probes start

sending temperature data within

1 hour from the base staon

start-up. Login to:

www.quanturi.app

for the data visualizaon.

79°C

74°C

68°C

62°C

55°C

49°C

45°C

38 °C

38°C

TemperatureID

1321

1232

1234

2223

1112

2333

2096

2124

2243

220V

NETWORK

ADAPTER



2 m



If the "NETWORK" LED does not light up:

B Repeat step 4 of the

installaon by unplugging and

reconnecng the cable.

C If the problem persists, contact: [email protected]

A Make sure to register to the

Quanturi.app service before

installing the base staon.

NETWORK

The NETWORK indicator is on when the network connecon is

79°C

74°C

68°C

62°C

55°C

49°C

45°C

38°C

TemperatureID

1321

1232

1234

2223

1112

2333

2096

2124

2243

220V

NETWORK

ADAPTER



2 m



ALERT

The ALERT indicator is on when one or more sensors have measured

temperatures above the alert level. You will receive SMS alert

messages in alert situaons.

79°C

74°C

68°C

62°C

55°C

49°C

45°C

38°C

TemperatureID

1321

1232

1234

2223

1112

2333

2096

2124

2243

220V

NETWORK

ADAPTER



2 m



Quanturi.app

Quanturi.app is the service

applicaon for visualizing the

sensor temperatures and for

customizing your account

sengs. The applicaon is

available under the web address:

hps://www.quanturi.app.

79°C

74°C

68°C

62°C

55°C

49°C

45°C

38 °C

38°C

TemperatureID

1321

1232

1234

2223

1112

2333

2096

2124

2243

220V

NETWORK

ADAPTER



2 m



Quanturi system acvaon.

27.6.2018

ALARM

Sensor 5498 73°C

12.7.2018

ALARM

Sensor 5487 71°C

79°C

74°C

68°C

62°C

55°C

49°C

45°C

38 °C

38°C

35°C

Quanturi

79°C

74°C

68°C

62°C

55°C

49°C

45°C

38 °C

38°C

TemperatureID

1321

1232

1234

2223

1112

2333

2096

2124

2243

Connecon symbols

Excellent Signal - Probes are sending data every hour

Good Signal - Probes are sending data every hour

Weak Signal - Probes are sending data less than every hour

Very Weak Signal - Probes are not sending data

Please refer to the steps below to solve this problem



220V

NETWORK

ADAPTER

200 m

200 m 200 m

200 m



220V

NETWORK

ADAPTER

200 m

200 m 200 m

200 m



220V

NETWORK

ADAPTER

200 m

200 m 200 m

200 m



220V

NETWORK

ADAPTER

200 m

200 m 200 m

200 m

If you don't receive any data in your dashboard:

1 Make sure you wait for at least one hour aer installing the base

staon unl the probes send the rst data.

established. The indicator is blinking when the base staon is sending

data to the Quanturi.app server. If the indicator is o, there is a

problem with the mobile GPRS data network connecon.

If one of your probes is not sending data:

1 Check that you have connected the baeries of the probes

properly. (HAYTECH probes only)

2 If you have a repeater, place the probe closer to the repeater and

wait for 2-3h.

A) If you receive some data, it means that your probe is too far

from the repeater. Move it closer.

B) If you don't receive any data, contact [email protected]

3 If you don't have a repeater, move the probe closer to the base

staon and wait for 2-3h.

A) If you receive some data, it means that your probe is too far

from the base staon. Move it closer.

B) If you don't receive any data, contact [email protected]

2 Check that you have connected the baeries of the probes

properly. (HAYTECH probes only)

3 Check that the base staon is connected to the internet (the green

NETWORK indicator should be on).

4 Check that the base staon is within the specied range from the

probes. (This also applies to the repeater, if installed.)

5 To check if the probes are working, move some of them closer to

the base staon and wait for 2-3h.

A) If you receive some data, it means that your base staon is

too far away from the other probes in the storage.

B) If you don't receive any data, contact [email protected]

6 If you have a repeater, place some of the probes closer to the

repeater and wait for 2-3h.

A) If you receive some data, it means that your repeater is too

far away from the other probes in the storage. Move it closer

to the probes in the storage.

B) If you don't receive any data, it means that your repeater is

too far away from the base staon. Move it closer.

7 If you sll don't receive any data at this point, contact us at

[email protected]

Repeater (oponal)

A repeater can be placed to cover probes in a second hay storage. The

distance between the base staon and the repeater is ideally less than

200 meters.

For professional

use only

Store at room

temperature

Do not store the

probes up-side down

Sharp spike, please

handle with care

Safety instrucons

Follow the safety instrucons to prevent harm or injury to yourself and

people near you when using the Quanturi System.

HAYTECH probes

Otros manuales para HAYTECH

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Maquinaria agrícola de Quanturi

Quanturi

Quanturi HAYTECH Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario