Qualstar XLS Series Manual de funcionamiento

‘

Technical Service

Manual

Document No. 501610

Rev. 07-01-19

XLS Series of Tape Libraries

501610 Rev. 07-01-19

2006

by Qualstar Corporation

—

Information contained in this document is copyrighted by Qualstar Corporation. It is intended for

use by Qualstar's customers and prospective customers to evaluate, integrate, operate, and

maintain Qualstar products. Customers and prospective customers may reproduce this document as

needed for these uses. Reproduction in whole or in part for any other use or by any other party is

prohibited without prior written permission from Qualstar Corporation.

Disclaimer

Every effort has been made to keep the information contained in this document current and

accurate as of the date of publication or revision. However, no guarantee is given or implied that the

document is error-free or that it is accurate with regard to any specification.

Qualstar reserves the right to modify the design or specification without notice. This specification

may not be construed as a contractual obligation except as specifically agreed to by Qualstar in

writing at the time of order.

Trademark Notices

Qualstar and the Qualstar logo are registered trademarks and X-Link is a trademark of Qualstar

Corporation. Other trademarks are the property of their respective owners.

Revision

History

Revision

Release

Date

Description

17-Apr-2007

Initial

rele

07-01-19

01-Jul-2019

Address updated

XLS

Library Technical Service

Manual

Notices

Qualstar products are covered by one or more of the following patents: 6,271,982; 6,560,061; and

7,181,313. Other patents pending.

Qualstar equipment is manufactured from new parts, or new and used parts. In some cases,

Qualstar equipment may not be new and may have been previously installed. Regardless,

Qualstar’s warranty terms apply unless the equipment is specifically identified by Qualstar as

“used” or “refurbished.”

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense. Shielded cables are

required for this device to comply with FCC Rules. Use shielded cables when connecting this device

to others.

European Union Directive 89/336/EEC and Standard

EN55022

(Electromagnetic

Compatibility)

This product has been tested and is certified to be compliant with the Class A provisions of the U.S.,

Canadian, and European standards for electromagnetic compatibility (EMC).

European Directive

Waste Electrical and Electronic Equipment (WEEE)

Qualstar encourages its customers to use current recycling practices in order to reduce

the burden that waste electronic products place on the environment.

If you are retiring a fully functional tape library, you are encouraged to transfer the

functional unit to a new user, thereby extending the useful life of the tape library. The

manufacture of all products requires the consumption of energy. By extending the life of the tape

library, energy is conserved.

In accordance with environmental directives that are being implemented in many countries (refer to

the European Directive on Waste Electrical and Electronic Equipment - WEEE), Qualstar provides

customers with “End of Life Instructions”that identify the process for recycling the materials

and components that make up a Qualstar tape library.

End

Life

Inst

ructions

Tools

required

•#1 and #2 Phillips screwdrivers

•T20 Torx head screwdriver

•Hex head (Allen) wrench/driver set

•1/4-inch hex nut driver

Disassembly

procedure

1. Remove the door(s).

2. Remove the front panel.

3. Remove the external side panels.

4. Remove the internal subassemblies.

501610 Rev. 07-01-19

Items recyclable using conventional

methods

•Aluminum: Front panel, exterior side and rear panels, robotics, cartridge and drive bays,

carousel and shroud panels

•Stainless steel: Robot guides

•Steel: Frames, fasteners

•Plastic: Windows, cartridge magazines, tape cassettes

•Copper: Internal wiring, motors, SCSI cables

•Paper: Manuals

Items requiring special disposal due

lead-based

solder

•Printed circuit boards: Controller card, miscellaneous small printed circuit boards

Items that may have salvage

resale

value

•Tape drives

•EMI line power filter

Reduction

Hazardous Substances

(RoHS)

Qualstar is committed to the implementation of RoHS (Restriction of the use of certain hazardous

substances in electrical and electronic equipment) in accordance with the European Directive. The

compliance date is July 1, 2006, at which time Qualstar will certify that its tape library products are

compliant with the RoHS standard.

Qualstar tape libraries are classified as “Information Technology Storage Array Systems”for which

the RoHS Directive provides an exemption for lead solder until the year 2010. Until Qualstar

replaces lead-based solder with lead-free solder, affected subassemblies must be disposed of

appropriately.

Technical

Suppo

The best source for service-related information is your system reseller. Alternately, you can reach

the Qualstar Technical Support Department at:

Qualstar Corporation

1267 Flynn Road

Camarillo, CA

93012

Monday

Friday

7:00 A.M.to 4:00 P.M.

Phone:(8

05) 416-7055

Toll Free: (877) 886-2758

E-mail:

support@

ualsta

com

-mail:

sale

s@qu

alstar

.com

www

.qualstar.com

XLS

Library Technical Service

Manual

Table of Contents

Part

Before You

Begin

Getting Started

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.1 How

This Manual Is Organized

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.2

Safety Notices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.3

Tools Check List.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1.4

Materials Check

List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.5

Conventions Used

This

Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.5.1

Terminology

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.5.2

Typographic Conventions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1.5.3

Safety Notices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1.6

For

MoreInformation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1.6.1

Related Manuals

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1.6.2

Contacting Qualstar.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

About

the

XLS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.1

Product

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.1.1

XLS-832700

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2.1.2

XLS-820500

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2.1.3

XLS-812300

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.2

Librar

Resource

Module

(LRM).

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2.2.1

Power/PC Bay

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2.2.2

Touch Screen

and

LEDs.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2.2.3

Robotic

Handlerand

Barcode Reader

. . . . . . . . . . . . . . . . . . . . . . 2-11

2.2.4

Tape

Drives

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

2.2.5

I/O

Ports

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

2.2.6

Cartridge

Slots

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

2.2.7

Doors

and

Light Curtain Sensors

. . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

2.2.8

quipment

Rack

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

2.3 Media

Expansion

Module

(MEM)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

501610 Rev. 07-01-19

Table

ontent

3.1

Diagrams

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Power

Distribution.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.2

CAN

Bus

Communication

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

3.3

X-YController DCB

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

3.4

Connections

to the

User Interface Controller DCB

. . . . . . . . . . . . . . . . . . . . . 3-7

3.5

ompo

nen

on the Gripper

Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

3.6

Cabling

for the Drive

Bay Assemblies

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

3.7

Cabling

for the

Carousel

Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Preventive Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1

Checking

the Air

Filter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2

Replacing

the Air

Filters

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

4.2.1

Removing

the Air

Filters.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

4.2.2

Installing

the Air

Filters.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4.3

Inspecting

the

Cartridge Slots

and

Fiducials

. . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4.4

Inspecting

the

Fans

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

4.5

Inspecting

and

Cleaning

the Gripperand

Barcode Reader

. . . . . . . . . . . . . . . 4-7

4.5.1

Powering

Off theGripper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4.5.2

Inspecting

and

Cleaning

the Gripper . . . . . . . . . . . . . . . . . . . . . . . . 4-9

4.5.3

Powering

On theGripperand

Resuming

Operation.. . . . . . . . . . . 4-11

Part

II:

Using

X-Link

Using X-Link Service

Options . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.1

Connecting

the

XLS

to aComputer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.1.1

Connecting

to aNetworkedComputer . . . . . . . . . . . . . . . . . . . . . . 5-3

5.1.2

Connecting

to a

Standalone

Computer . . . . . . . . . . . . . . . . . . . . . . 5-4

5.2

Logging

Into X-Link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

5.3

cces

ing

the

Service

Portlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

5.4

Changing

the

Operating

Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

5.4.1 About

Logical

and

Physical Libraries

. . . . . . . . . . . . . . . . . . . . . . . . 5-8

5.4.2 About

Logical

and

Physical

Modes

. . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

5.4.3

Putting

the

XLS

Physical

Mode. . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

5.4.4

Putting

the

XLS

Logical

Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

5.5

Performing Diagnostics

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

5.5.1

xecuting

aCommand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

5.5.2

Auditing

the

Library

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13

5.5.3

Viewing

the

SCSI

Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

5.5.4

Using

the

Service

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15

Table

ent

XLS

Library Technical Service

Manual

7.1

Installi

Replacing

Power Supply

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

7.1.1

Removing

Power

Sup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

7.1.2

Installing

Power Supply

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

5.6

Changing

the

Configuration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17

5.6.1

Uploading

aFile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

5.6.2

Installing

File.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19

5.6.3

Viewing

Editing SCSI Log Settings

. . . . . . . . . . . . . . . . . . . . . . . 5-20

Shutting Down

the

XLS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.1 What

Happens

When the

XLS is Shut

Down . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.2

hutting

Down the

XLS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.3

Restarting

the

XLS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Part

III:

Replacing

FRUs

Replacing Power/PC Bay Components

. . . . . . . . . . . . . . . . . . . . 7-1

7.2

Replacing

the

Battery

Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

7.2.1

Removing

the

Battery

Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

7.2.2

Installing

the

Battery

Module

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

7.3

lidin

the

Power/PC Bay

In andOut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11

7.3.1

liding

the

Power/PC Bay

Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11

7.3.2

liding

the

Power/PC Bay

In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

7.4

Replacing

Fan

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

7.4.1

Removing

Fan.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13

7.4.2

Installing

aFan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

7.5

Replacing System Controller Components

. . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

7.5.1

cces

ing

System Controller Components

. . . . . . . . . . . . . . . . . . . 7-15

7.5.2

Replacing PCI Cards

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16

7.5.3

Replacing

the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

7.5.4

Replacing

the

System Controller

Cover . . . . . . . . . . . . . . . . . . . . . 7-20

7.6

Replacing

the

Power/PC Bay Assembly.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

7.6.1

Removing

the

Power/PC Bay Assembly

. . . . . . . . . . . . . . . . . . . . . 7-21

7.6.2

Installing

the

Power/PC Bay Assembly

. . . . . . . . . . . . . . . . . . . . . . 7-24

7.7

Replacing

the

Power/PC Bay Slide Rails

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

7.7.1

Removing

the

Slide Rails

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

7.7.2

Installing

the

Slide Rails

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26

Table

ontent

501610 Rev. 07-01-19

Replacing Tape

Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

8.1

cces

ing

the

View/Manage Tape Drives

Page

. . . . . . . . . . . . . . . . . . . . . . . . 8-2

8.2

Taking

Tape

Drive

ffline

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

8.3

Powering

Off a

Tape

Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

8.4

Removing

Tape

Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

8.5

Installing

Tape Drive

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

8.6

Applying Power

to a

Tape

Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

8.7

Calibrating

Tape

Drive

(optional).

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11

8.8

Bringing

Tape

Drive Online. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

nstalling

Replacing Cartridge Slots and

Drive

Bays

. . . . . . . 9-1

9.1

XLS Fiducials

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

9.2

Replacing

Cartridge Magazine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

9.2.1

Removing

Cartridge

Magazine. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

9.2.2

Installing

Cartridge Magazine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

9.3

Installing

and

Removing

Door

Slots

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

9.3.1

Installing

Door

Slots

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

9.3.2

Removing

Door

Slots

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7

9.4

Replacing

Cartridge Bay

with aDrive

Bay

. . . . . . . . . . . . . . . . . . . . . . . . . 9-10

9.4.1

Removing

Cartridge Bay

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11

9.4.2

Installing

aDrive

Bay

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13

9.5

Replacing

aDrive

Bay

with a

Cartridge Bay

. . . . . . . . . . . . . . . . . . . . . . . . . 9-16

9.5.1

Removing

aDrive

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17

9.5.2

Installing

Cartridge Bay

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20

Replacing Frame Components

. . . . . . . . . . . . . . . . . . . . . . . . 10-1

10.1

Removing

the

Front Panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

10.1.1

Removing Front Panel Cartridges

. . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

10.1.2

Removing

the Air

Filter

Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

10.1.3

Detaching

the Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

10.1.4

Removing

the

Front Panel

from the

Frame.

. . . . . . . . . . . . . . . . . . 10-5

10.2

Installin

the

Front Panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7

10.2.1

Inserting

the

Front Panel

in the

Frame

. . . . . . . . . . . . . . . . . . . . . . 10-8

10.2.2

Attaching

the

Cables

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9

10.2.3

Replacing

the Air

Filter

Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10

10.2.4

Replacing

the

Cartridges

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

10.3

Replacing

Side Panel.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

10.3.1

Removing

Side

Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

10.3.2

Installing

Side Panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12

Table

ent

XLS

Library Technical Service

Manual

Replacing

I/O

Ports and Fixed Port Assemblies

. . . . . . . . . . . 11-1

11.1

Replacing

anI/O

Port.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

11.1.1

Removing

anI/O Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

11.1.2

Installing

anI/O Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5

11.2

Replacing

Fixed Port Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7

11.2.1

Removing

Fixed Port Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . 11-7

11.2.2

Installing

Fixed Port Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8

11.3

Upgrading

Fixed Port Assembly

to anI/O

Port

. . . . . . . . . . . . . . . . . . . . . . 11-9

11.3.1

Removing

Fixed Port Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . 11-10

11.3.2

Installing

anI/O Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11

Replacing Handler Components

. . . . . . . . . . . . . . . . . . . . . . . 12-1

12.1

Replacing

theGripper

Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2

12.1.1

Powering

Off the Gripper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3

12.1.2

Removing

theGripper

Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . 12-5

12.1.3

Installing

the

Gripper Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7

12.1.4

Aligning

the Gripper

Assembly

with the

Left Back

Wall . . . . . . . . . 12-9

12.1.5

Aligning

the Gripper

Assembly

with the

Right Back

Wall . . . . . . . 12-10

12.1.6

Aligning

the Gripperwith Any

MEMs

. . . . . . . . . . . . . . . . . . . . . . 12-11

12.1.7

Updating

the

Database

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-12

12.1.8

Scanning

the

Fiducials

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

12.2

Replacing

the

X-YController Card

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-15

12.2.1

Removing

the

X-Y Controller

Card

. . . . . . . . . . . . . . . . . . . . . . . . 12-16

12.2.2

Installing

the

X-Y Controller

Card

. . . . . . . . . . . . . . . . . . . . . . . . . 12-18

12.3

Replacing

the

X-Axis Cable

and

Cat

Track. . . . . . . . . . . . . . . . . . . . . . . . . 12-19

12.3.1

Removing

the

X-Axis Cable

and

Cat Track

. . . . . . . . . . . . . . . . . . 12-20

12.3.2

Installing

the

X-Axis Cable

and

Cat Track

. . . . . . . . . . . . . . . . . . . 12-22

12.4

Replacing

theX-Motor

Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22

12.4.1

Removing

the

X-Axis

Motor

Assembly

. . . . . . . . . . . . . . . . . . . . . 12-23

12.4.2

Installing

the X-Motor

sembly

. . . . . . . . . . . . . . . . . . . . . . . . . . 12-26

12.5

Replacing

the

Y-Axis Cable

and

Cat

Track. . . . . . . . . . . . . . . . . . . . . . . . . 12-30

12.5.1

Removing

the

Y-Axis Cable

and

Cat Track

. . . . . . . . . . . . . . . . . . 12-30

12.5.2

Installing

the

Y-Axis Cable

and

Cat Track

. . . . . . . . . . . . . . . . . . . 12-33

12.6

Replacing

the

Y-Motor Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-34

12.6.1

Removing

the

Y-Axis

Motor

Assembly

. . . . . . . . . . . . . . . . . . . . . 12-34

12.6.2

Installing

the

Y-Motor

Ass

mbly

. . . . . . . . . . . . . . . . . . . . . . . . . . 12-37

Replacing

the

Touch Screen and User Interface Assemblies

. 13-1

13.1

Replacing

the

Touch Screen Assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

13.1.1

Removing

the

Touch Screen Assembly.

. . . . . . . . . . . . . . . . . . . . . 13-2

13.1.2

Installing

the

Touch Screen Assembly.

. . . . . . . . . . . . . . . . . . . . . . 13-4

13.1.3

Calibrating

the

Touch Screen.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5

Table

ontent

501610 Rev. 07-01-19

13.2

Replacing

the

User Interface

sembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5

13.2.1

Removing

the

User Interface Assembly

. . . . . . . . . . . . . . . . . . . . . 13-6

13.2.2

Installing

the

User Interface Assembly

. . . . . . . . . . . . . . . . . . . . . . 13-8

Replacing Library Sensors and Solenoids

. . . . . . . . . . . . . . . . 14-1

14.1

Replacing

aDoor

Interlock

Sen

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

14.1.1

Removing

aDoor

Interlock Sensor.

. . . . . . . . . . . . . . . . . . . . . . . . 14-2

14.1.2

Installing

aDoor

Interlock Sensor

. . . . . . . . . . . . . . . . . . . . . . . . . 14-3

14.2

Replacing

Door-Lock

Solenoid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4

14.2.1

Removing

Door-Lock Solenoid

. . . . . . . . . . . . . . . . . . . . . . . . . . 14-4

14.2.2

Installing

Door-Lock Solenoid

. . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5

14.3

Replacing

anI/O

Port

Open

Sensor

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5

14.3.1

Removing

anI/O

Port

Open

Sensor

. . . . . . . . . . . . . . . . . . . . . . . . 14-6

14.3.2

Installing

anI/O

Port

Open

Sen

or.

. . . . . . . . . . . . . . . . . . . . . . . . 14-7

14.4

Replacing

anI/O

Port

Solenoid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8

14.4.1

Removing

anI/O

Port Solenoid

. . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8

14.4.2

Installing

anI/O

Port Solenoid

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9

14.5

Replacing Light Curtain Sensors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10

14.5.1

Removing

the

Light Curtain

Sensors

. . . . . . . . . . . . . . . . . . . . . . . 14-13

14.5.2

Installing

the

Light Curtain Sensors.

. . . . . . . . . . . . . . . . . . . . . . . 14-18

Replacing

MEM

Components

. . . . . . . . . . . . . . . . . . . . . . . . . 15-1

15.1

Ins

ling

aMEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1

15.1.1

Preparing

the LRM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3

15.1.2

Removing

the

X-Axis

Hard

Stop

. . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4

15.1.3

Releasing

the

Carousel

Locks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6

15.1.4

Connecting

the

Carousel Controller Cable

. . . . . . . . . . . . . . . . . . . 15-8

15.1.5

Attaching

the

LRM

to theMEM. . . . . . . . . . . . . . . . . . . . . . . . . . 15-10

15.1.6

Lowering

the

Leveling

Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-11

15.1.7

Lowering

the

Carousel Supports

. . . . . . . . . . . . . . . . . . . . . . . . . 15-13

15.1.8

Installing

the

Side Panel

on the MEM.. . . . . . . . . . . . . . . . . . . . . 15-14

15.1.9

Applying Power

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-14

15.1.10

Aligning

theGripperwith the

MEM

. . . . . . . . . . . . . . . . . . . . . . . 15-16

15.1.11

Updating

the

Hardware

Con

iguration

. . . . . . . . . . . . . . . . . . . . . 15-19

15.1.12

can

ing

the

Fiducials

and

Inventory

. . . . . . . . . . . . . . . . . . . . . . 15-19

15.2

Replacing

the

MEM

’

Door

Solenoid Assembly

. . . . . . . . . . . . . . . . . . . . . 15-21

15.2.1

Removing

the Door

Solenoid Assembly

. . . . . . . . . . . . . . . . . . . . 15-21

15.2.2

Installing

the Door

Solenoid Assembly

. . . . . . . . . . . . . . . . . . . . . 15-22

15.3

Replacing

the

Carousel

Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23

15.3.1

Powering

Off the

Carousel

Controller . . . . . . . . . . . . . . . . . . . . . 15-23

15.3.2

Removing

the

Carousel

Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . 15-25

15.3.3

Installing

the

Carousel Motor

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-28

15.3.4

Powering

the

Carousel Controller Back

On . . . . . . . . . . . . . . . . . 15-30

Otros manuales para XLS Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Qualstar

Qualstar

Qualstar RLS-8350 Manual de usuario

Qualstar

Qualstar Q40 Manual de usuario

Qualstar

Qualstar HP9000 Manual de usuario

Qualstar

Qualstar Q1 Manual de usuario

Qualstar

Qualstar XLS-810160 Manual técnico

Qualstar

Qualstar RLS-8350 Manual de funcionamiento

Qualstar

Qualstar RLS-4470 Manual de funcionamiento

Qualstar

Qualstar XLS Series Manual técnico

Qualstar

Qualstar XLS Series Manual de usuario

Qualstar

Qualstar Q48 Manual de usuario

Qualstar

Qualstar Qi Desktop LTO SAS Manual de usuario

Qualstar

Qualstar 9-Track Tape Drives 3400 Series Manual de usuario

Qualstar

Qualstar Qi Manual de usuario

Qualstar

Qualstar Q40 Manual de usuario

Qualstar

Qualstar 105X Manual de usuario

Qualstar

Qualstar 34XX Series Manual de usuario

Qualstar

Qualstar 1260 Manual de usuario

Qualstar

Qualstar Q24 Manual de usuario

Qualstar

Qualstar RLS-8350 Manual del propietario

Qualstar

Qualstar Q80 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario