Quadra-Fire CLASSIC BAY 1200 Manual de usuario

1June 4, 20197027-801C

CLASSIC BAY 1200 PELLET

APPLIANCE

MODEL:

CB1200-C

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

CAUTION

Tested and approved for wood pellets and shelled eld

corn fuel only. Burning of any other type of fuel voids

your warranty.

NOTE: To obtain a French translation of this

manual, please contact your dealer or visit

www.quadrare.com

REMARQUE : Pour obtenir une traduction française de

ce manuel, s’il vous plaît contacter votre

revendeur ou visitez www.quadrare.com

If the information in these instructions is

not followed exactly, a re could result

causing property damage, personal injury,

or death.

WARNING

• Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any

other appliance.

• Do not over re - If appliance or chimney connector

glows, you are over ring. Over ring will void

your warranty.

• Comply with all minimum clearances to combustibles

as specied. Failure to comply may cause house re.

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

WARNING

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high

temperatures

• High temperatures may ignite clothing or other

ammable materials.

• Keep clothing, furniture, draperies and other

ammable materials away.

CAUTION

Check building codes prior to installation.

• Installation MUST comply with local, regional, state

and national codes and regulations.

• Consult local building, re o󰀩cials or authorities

having jurisdiction about restrictions, installation

inspection, and permits.

2June 4, 20197027-801C

CB1200 Free Standing

TABLE OF CONTENTS

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the appliance or to property.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

1 Important Safety Information............. 3

A. Appliance Certication........................3

B. BTU & E󰀩ciency Specications ................3

C. Glass Specications .........................4

D. Electrical Rating ............................4

E. Mobile Home Approved .......................4

F. Non-Combustible Materials ....................4

G. Combustible Materials .......................4

H. Sleeping Room .............................4

I. California - Prop65 ...........................4

2 Getting Started .................................... 5

A. Design, Installation & Location Considerations .....5

B. Thermostat Wall Control Location ...............6

C. Tools And Supplies Needed ...................6

D. Inspect Appliance and Components .............6

E. Install Checklist .............................7

3 Dimensions and Clearances.............. 8

A. Appliance Dimensions ........................8

B. Clearances to Combustibles (UL and ULC) ......10

C. Hearth Pad Requirements (UL and ULC) ........11

D. Alcove ...................................12

4 Vent Information................................ 13

A. Venting Termination Minimum Requirements .....13

B. Avoiding Smoke and Odors...................14

C. Draft ....................................14

D. Negative Pressure..........................15

E. Chimney and Exhaust Connection .............15

F. Equivalent Feet of Pipe ......................16

G. Pipe Selection Chart ........................16

5 Venting Systems ............................... 17

A. Through The Wall ..........................17

B. Vertical into Existing Class A Chimney ..........18

C. Through The Wall & Vertical - Exterior ..........18

D. Vertical - Interior - Typical Installation . . . . . . . . . . .18

E. Masonry..................................19

F. Alternate Masonry ..........................19

6 Appliance Set-Up .............................. 20

A. Outside Air Kit Instructions ...................20

B. Top Vent Adapter Installation..................21

C. Rear Vent & Rear Vent to Top Vent Adapter ......21

D. Thermostat Installation and Operation ..........21

E. Optional Log Set Placement Instructions ........23

F. Installing Logo .............................23

7 Mobile Home Installation.................. 24

8 Accessory List .................................. 25

A. Service & Maintenance Log ..................25

B. Accessory List .............................26

3June 4, 2019 7027-801C

CB1200 Free Standing

Model CB1200 Pellet Appliance

Laboratory OMNI Test Laboratories, Inc.

Safety

Report No. 061-S-21-4

Type Solid Fuel Room Appliance/Pellet Fuel

Burning Type

Standard

ASTM E1509-04, ULC S627-00 and

ULC/ORD-C1482-M1990 Room

Appliance Pellet Fuel Burning type and

(UM) 84-HUD, Mobile Home Approved.

Emissions Report No: 0061PS013E

EPA Certication #: 176-19

EPA Certied Emissions: 1.1 grams per hour

*LHV Tested E󰀩ciency: 77.8%

**HHV Tested E󰀩ciency: 72.7%

***EPA BTU Output: 11,100 - 30,900 / hr

****BTU Input: 15,900 - 41,100 / hr

Vent Size: 3 or 4 inches “L” or “PL”, or

6 inches

Hopper Capacity: 80 lbs.

Fuel: Premium Wood Pellets

*Weighted average LHV (Low Heating Value) e󰀩ciency

using data collected during EPA emissions tests.

**Weighted average HHV (High Heating Value) e󰀩ciency

using data collected during EPA emissions tests.

***A range of BTU outputs calculated using HHV

e󰀩ciency and the burn rates from the EPA tests.

****Based on the maximum feed rate per hour multiplied

by approximately 8600 BTU’s which is the average BTU’s

from a pound of pellets.

‡ Grade of pellet fuel as certied by Pellet Fuels Institute (PFI), ENPlus

or CANplus.

1 Important Safety Information

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM

E1509-04, ULC S627-00, (UM) 84-HUD and ULC/ORD-C-1482.

A. Appliance Certication B. BTU & E󰀩ciency Specications

This pellet appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate

this pellet appliance in a manner inconsistent with operating instructions in this manual.

This Classic Bay 1200 is

Certied to comply with 2020

particulate emission standards.

4June 4, 20197027-801C

CB1200 Free Standing

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualied

installer, service agency or your dealer.

C. Glass Specications

This appliance is equipped with 5mm ceramic glass.

Replace glass only with 5mm ceramic glass. Please contact

your dealer for replacement glass.

F. Non-Combustible Materials

Material which will not ignite and burn, composed of any

combination of the following:

- Steel

- Plaster

- Brick

- Iron

- Concrete

- Tile

- Glass

- Slate

Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace of 750° C.

D. Electrical Rating

115 VAC, 60 Hz, Start 3.75 Amps, Run 1.88 Amps

E. Mobile Home Approved

• This appliance is approved for mobile home

installations when not installed in a sleeping room and

when an outside combustion air inlet is provided.

• The structural integrity of the mobile home oor, ceiling,

and walls must be maintained.

• The appliance must be properly grounded to the frame

of the mobile home and use only Listed pellet vent

Class “L” or “PL” connector pipe.

• Outside Air Kit, part 811-0570 or 811-0872 must be

installed in a mobile home installation.

G. Combustible Materials

Material made of/or surfaced with any of the

following materials:

- Wood

- Compressed Paper

- Plant Fibers

- Plastic

- Plywood/OSB Sheet Rock (drywall)

Any material that can ignite and burn: ame proofed or not,

plastered or non-plastered.

H. Sleeping Room

When installed in a sleeping room it is recommended that

3ft of vertical be installed prior to horizontally exiting the

room and a smoke/CO alarm be installed in the bedroom.

The size of the room must be at least 50ft³ per 1,000 Btu/hr

stove input, if the stove exceeds the room size, outside air

must be installed.

I. California - Prop65

WARNING

This product and the fuels used to operate this product (wood), and

the products of combustion of such fuels, can expose you to

chemicals including carbon black, which is known to the State of

California to cause cancer, and carbon monoxide, which is known to

the State of California to cause birth defects or other reproductive

harm. For more information go to: WWW.P65Warnings.ca.gov

NOTE: Hearth & Home Technologies, manufacturer

of this appliance, reserves the right to alter

its products, their specications and/or price

without notice.

• Installation and use of any damaged appliance.

• Modication of the appliance.

• Installation other than as instructed by Hearth &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

• Operating appliance without fully assembling

all components.

• Operating appliance without legs attached (if

supplied with appliance).

• Do NOT Over re - If appliance or chimney connector

glows, you are over ring.

Any such action that may cause a re hazard.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

5June 4, 2019 7027-801C

CB1200 Free Standing

Install Guide

2 Getting Started

Recommended

Location

Marginal

Location

Not

Recommended

Location

Location NOT

Recommended

Multi-level Roofs

Windward

Leeward

Outside Air Kit Termination Cap

Figure 5.1

A. Design, Installation & Location

Considerations

1. Appliance Location

Since pellet exhaust can contain ash, soot or sparks, you

must consider the location of:

- Windows

- Air Intakes

- Air Conditioner

- Overhang, so󰀩ts, porch roofs, adjacent walls

- Landscaping, vegetation

- Horizontal or vertical vent termination

2. Floor Support

The supporting oor under the appliance must be able to

handle the weight of the appliance, fuel load and the weight

of the chimney.

Ensure that your oor will support these weights prior to

installation. Add su󰀩cient additional support to meet this

weight requirement prior to installation. The weight of the

appliance is 238 lbs.

WARNING

Risk of Fire.

Damaged parts could impair safe operation. Do NOT

install damaged, incomplete or substitute components.

NOTICE: Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector,

re o󰀩cials or authorities having jurisdiction over

restrictions, installation inspection and permits.

It is a good idea to plan your installation on paper, using

exact measurements for clearances and oor protection,

before actually beginning the installation. Location of the

appliance and chimney will a󰀨ect performance.

Consideration must be given to:

- Safety, convenience, tra󰀩c ow

- Placement of the chimney and chimney connector

and to minimize the use of chimney o󰀨sets.

- Place the appliance where there will be a clear

passage for a Listed chimney through the

ceiling and roof (vertical) or through exterior

wall (horizontal).

- Installing the required outside air kit will a󰀨ect the

location of the vent termination.

When locating vent and venting termination, the ideal

location is to vent above roof line when possible. This

minimizes the a󰀨ects of wind loading.

6June 4, 20197027-801C

CB1200 Free Standing

Tools and building supplies normally required

for installation, unless installing into an existing

masonry replace:

- Reciprocating Saw

- Channel Locks

- Hammer

- Phillips Screwdriver

- Tape Measure

- Plumb Line

- 1/4” Self-Tapping Screws

- Framing Material

- Hi-temp Caulking Material

- Gloves

- Safety Glasses

- Framing Square

- Electric Drill & Bits (1/4”)

- Level

May also need:

- Vent Support Straps

- Venting Paint

C. Tools And Supplies Needed

B. Thermostat Wall Control Location

The thermostat wall control’s location will have some a󰀨ect

on the appliance’s operation.

• Maximum wire length from appliance is 100 feet

(30.48m) continuous non-spliced wire. Recommended

18 to 22 gauge wire, solid copper.

• When located close to the appliance, it may require a

slightly higher temperature setting to keep the rest of

the house comfortable.

• When located in an adjacent room or on a di󰀨erent

oor level, you will notice higher temperatures near

the appliance.

D. Inspect Appliance and Components

• Open the appliance and remove all the parts and

articles packed inside the Component Pack. Inspect all

the parts and glass for shipping damage.

• Report to your dealer any parts damaged in shipment.

• All labels have been removed from the glass door.

• Plated surfaces have been wiped clean with a soft

cloth, if applicable.

• Read all the instructions before starting the installation.

Follow these instructions carefully during the

installation to ensure maximum safety and benet.

• Follow pipe manufacturer instructions for installation

and air clearance requirements.

Risk of Fire!

• Damaged parts could impair safe

operation.

• Do NOT install damaged, incomplete or

substitute components.

WARNING

• Installation and use of any damaged appliance.

• Modication of the appliance.

• Installation other than as instructed by Hearth &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

• Operating appliance without fully assembling

all components.

• Operating appliance without legs attached (if

supplied with appliance).

• Do NOT Over re.

Or any such action that may cause a re hazard.

WARNING

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

7June 4, 2019 7027-801C

CB1200 Free Standing

E. Install Checklist

YES IF NO, WHY?

Verified clearance to combustibles.

Appliance is leveled and connector is secured to appliance.

Hearth extension size/height decided.

Outside air kit installed.

Floor protection requirements have been met.

If appliance is connected to a masonry chimney, it should be cleaned and

inspected by a professional. If installed to a factory built metal chimney, the

chimney must be installed according to the manufacturer’s instructions and

clearances.

Appliance Install

Chimney configuration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimney meets recommended height requirements (5 feet minimum vertical).

Roof flashing installed and sealed.

Terminations installed and sealed.

Venting/Chimney

Clearances

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

Floor protection and heart extensions installed per manual requirements.

Appliance Setup

All protective materials removed.

All labels have been removed from the door.

All packaging materials are removed from inside/under appliance.

Manual bag and all of its contents are removed from inside/under the appliance

and given to the party responsible for use and operation.

WARNING! Risk of Fire or Explosion! Failure to install appliance to these instructions can lead to a fire or

explosion.

Hearth & Home Technologies recommends the following:

Photographing the installation and copying this checklist for your file.

That this checklist remain visible at all times on the appliance until the installation is complete.

Electrical

120 VAC unswitched power provided to the appliance.

Check outlet with multi-meter for proper polarity and voltage (115-120 VAC).

Record voltage reading: _____________

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.

Customer:

Date Installed:

Lot/Address:

Location of Appliance:

Installer:

Dealer/Distributor Phone Number:

Serial Number:

Model Name:

__________________________________________________________________________

______________________________________________________________________

_______________________________________________________________________

________________________________________________________________

___________________________________________________________________________

________________________________________________________

______________________________________________________________________

_______________________________________________________________________

Started appliance and verified that all motors and blowers operate as they should.

Checked draft using a Manometer. Record readings: ______________________

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, ets.) and corrective action needed:

Comments communicated to party responsible __________________________ by ______________________ on ____________

(Builder/Gen. Contractor) (Installer) (Date)

Checked vacuum using a Manometer. Record readings: ____________________

8June 4, 20197027-801C

CB1200 Free Standing

Figure 8.1 - Top View

Figure 8.2 - Side View

Figure 8.3 - Front View

6-1/4

[159]

[203]

25-3/4 [654]

27-5/8 [702]

[204]

25-3/4 [654]

28-1/2 [724]

31-5/8

[803]

28-1/2 [725]

21-1/4 [539]

10-3/8

[264]

2-3/8

[62]

3-5/8

[94]

[127]

14-1/4 [362]

33-3/8

[847]

31-1/4

[795]

2-3/8

[62]

2-3/4

[69]

[127]

14-1/4 [362]

Figure 8.4 - Top View with Top Vent Adapter (TPVNT-1) and

O󰀨set Adapter (812-3570)

Figure 8.5 - Side View with Top Vent Adapter (TPVNT-1) and

O󰀨set Adapter (812-3570)

Figure 8.6 - Top View with Top Vent Adapter (TPVNT-1) and

O󰀨set Adapter (811-0720)

3 Dimensions and Clearances

A. Appliance Dimensions

9June 4, 2019 7027-801C

CB1200 Free Standing

33-1/8

[841]

31-1/4

[795]

Figure 9.1 - Side View with Top Vent Adapter (TPVNT-1) and

O󰀨set Adapter (811-0720)

2-3/8

[62]

2-3/4

[69]

3-7/8

[100]

6-1/4

[159]

[203]

Figure 9.2 - Top View with Top Vent Adapter (TPVNT-6) and

O󰀨set Adapter (811-0720)

15-51/8

[398]

[357]

Figure 9.3 - Side View with Top Vent Adapter (TPVNT-6) and

O󰀨set Adapter (811-0720)

10 June 4, 20197027-801C

CB1200 Free Standing

Installations with:

TPVNT-1 Top Vent Adapter with Heat Shield

and Clean-out

TPVNT-6 Top Vent Adapter with Clean-out

811-0720 (3” to 4”) O󰀨set Adapter

812-3570 (3” to 6”) O󰀨set Adapter

NOTE:

• Illustrations reect typical installations and are FOR

DESIGN PURPOSES ONLY.

• Illustrations/diagrams are not drawn to scale.

• Actual installation may vary due to individual

design preference.

Horizontal Through the Wall Inches Millimeters

ABack Wall to Appliance 2 51

BSide Wall to Appliance 6 152

Corner Installation Inches Millimeters

CWalls to Appliance 2 51 Vertical Installation Inches Millimeters

DBack Wall to Flue Pipe 3 76

ESide Wall to Appliance Top 6 152

FBack Wall to Appliance 7.5 191

Corner Installation Inches Millimeters

GSide Walls to Appliance 2 51

B. Clearances to Combustibles (UL and ULC)

Otros manuales para CLASSIC BAY 1200

Tabla de contenidos

Otros manuales de Cocina de Quadra-Fire

Quadra-Fire

Quadra-Fire CASTILE-B Manual de usuario

Quadra-Fire

Quadra-Fire Mt. Vernon Series Manual de usuario

Quadra-Fire

Quadra-Fire EXPLR-III-PBK Manual de usuario

Quadra-Fire

Quadra-Fire DISCOVERY-III Manual de usuario

Quadra-Fire

Quadra-Fire Direct Room CASTILE-GAS-CSB Manual de usuario

Quadra-Fire

Quadra-Fire CASTILE-MBK-B Manual de usuario

Quadra-Fire

Quadra-Fire CASTILE-CE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire MT. VERNON AE Manual de programación

Quadra-Fire

Quadra-Fire CASTILE-MBK-C Manual de usuario

Quadra-Fire

Quadra-Fire MTVI-E2-MBK-C Manual de usuario

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Manual de usuario

Quadra-Fire

Quadra-Fire GARN-MBK-IPI Manual de usuario

Quadra-Fire

Quadra-Fire SAPPHIRE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire SAPH-MBK-IPI Manual de usuario

Quadra-Fire

Quadra-Fire QFI30FB-IFT Manual de usuario

Quadra-Fire

Quadra-Fire CASTILE-B series Manual de usuario

Quadra-Fire

Quadra-Fire Garnet Manual

Quadra-Fire

Quadra-Fire DV-40 Manual de usuario

Quadra-Fire

Quadra-Fire Pioneer-II-C Manual de usuario

Quadra-Fire

Quadra-Fire HUDBAY-FS Manual de usuario

Quadra-Fire

Quadra-Fire CLASSIC BAY 1200 Manual de usuario

Quadra-Fire

Quadra-Fire SAPPHIRE Sapphire Cast Iron Manual de usuario

Quadra-Fire

Quadra-Fire GRAND BAY 40 GB40FS Manual de usuario

Quadra-Fire

Quadra-Fire GARN-DMBK-IPI-B Manual de usuario

Manuales populares de Cocina de otras marcas

Arada

Arada Cassette Stove Manual de usuario

Parmco

Parmco FS 600 Manual de usuario

MCZ

MCZ SUITE AIR 10 M2 Manual de usuario

HearthStone

HearthStone Stowe DV 8321 Guía de solución de problemas

Cattara

Cattara FAMILY Manual de usuario

Stanley

Stanley Argon F500 OVAL Manual de usuario

Avalon

Avalon B-VENT Manual de usuario

Nordpeis

Nordpeis Vega Manual de usuario

Exquisit

Exquisit EKC601-5 Manual de operación

Stanley

Stanley Oisin Oil MK II Manual del propietario

Thermocet

Thermocet Brookfield S/CC Manual de usuario

HASE

HASE delhi Manual de usuario

Vermont Castings

Vermont Castings Intrepid 2 Manual de usuario

Italiana Camini

Italiana Camini CLASSICA Guía de inicio rápido

Avalon

Avalon Vashon Avanti DVS FS Manual de usuario

Spartherm

Spartherm ambiente a1 Manual de usuario

Dimplex

Dimplex MCFSTV12AU Manual de usuario

Warmlite

Warmlite WL46040 Manual de usuario