Qtx PAJ-12A Manual de usuario
Quick Set-Up Instructions:
1.- Plug a IEC power cable from a wall power outlet, to the PAJ-12A.
2.- Plug a Microphone into the “MIC” input (1a, 1b) with a 6.35mm or
XLR connector.
3.- Plug an auxiliary system (CD, DJ Mixer, MP3, DVD, etc) into the
“LINE IN” input.
4.- Turn on the speaker amplifier on by flicking the “Power” switch (9). A
green LED will light up to indicate that is on.
5.- Set the volume of the MIC and LINE IN inputs to “12 o’clock”.
6.- Gradually increase the “MASTER” volume (3) until the desired
loudness is reached.
7.- Set TREBLE and BASS controls to equalise the sound.
8.- A red LED will light up on the front of the speaker if the system
detects an overload, or peak signal. In this case you must reduce the
volume level of the MIC or LINE inputs, and /or the MASTER volume.
Before using your new PAJ-12A powered speaker, please read this
instruction manual to prevent any damage or personal injury. Keep
it away in a safe place for future reference.
NOTE: Before connecting the speaker to a power outlet, make sure the
speaker amplifier is off and the controls are on the minimum level. Otherwise
the speaker may be damaged when power is turned on.
Caution
Do not point a microphone towards the speaker, it can cause
feedback to occur which can damage both the speaker and
human ears.
Used wisely, your new powered speaker will provide many years of
reliable sound reinforcement. Though note that hearing damage can
be caused by loud noise is often undetectable until it is too late.
We recommend that you avoid prolonged exposure to excessive
noise. This list of sound levels is included for your protection.
The following sound levels can be dangerous under constant exposure:
Level (Decibels) Example
30 40 50 60 70 80 Quiet library, soft whispers Living room, refrigerator,
bedroom Light traffic, normal conversation, quiet office
Air conditioner at 20ft, sewing machine Vacuum cleaner,
hair dryer, noisy restaurant Average city traffic, alarm
clock at two feet
90 Subway, motorcycle, lawn mower
100 Pneumatic drill, garbage truck
120 Rock band concert in front of speakers, thunderclap
140 Gunshot blast, jet plane
180 Rocket launching pad
Balanced 6.35mm and XLR connectors marked as LINE OUT can supply
a line level signal to another or PAJ-12A. The bottom of the speaker has
a standard s
p
eaker stand hole.
• Polarized IEC input to connect to a wall power outlet.
• Microphone Inputs: (balanced) XLR and (unbalanced) 6.35mm
• Line Level Inputs: Dual (stereo) RCA and (stereo) XLR
• Line Outputs: (balanced) 6.35mm and (balanced) XLR
• LEDS to indicate power on (green) and overload power (red)
• On and off switch
• Auxiliary and microphone volume controls
• Master volume control
• Bass and treble controls
• Protective fuse
• Store in a dry environment
• Do not use it in places with high humidity or in wet weather
• Do not hold drinks on it
1a) Microphone input (balanced)
A
llows you to connect an unbalanced microphone with a 6.35mm
connector.
1b) Microphone input (balanced)
A
llows you to connect a balanced microphone with a XLR
connector.
1c) Microphone volume control
Use this control to set the volume level of the microphone 1 (6,3mm or
balanced)
2a) RCA Line-In
A
llows you to connect an external audio device with RCA connectors (CD,
Mixer, DVD, etc.), outputting a Line Level signal.
2b) XLR Line-In (stereo)
A
llows you to connect an external audio device (CD, Mixer, DVD, etc.),
outputting a Line Level signal. Note, this is not a “balanced” XLR input.
2c) Line input Control
Use this control to set the volume level of the Line-In signal
3) Master Volume control
Set the volume level
4) Treble
Use it to adjust the level of treble frequencies
5) Bass
Use it to adjust the level of bass frequencies
6a) Balanced Line Level 6.35mm Link output
Use this 6.35mm output to link the signal to another amplifier or PAJ-12A.
6b) Balanced Line Level XLR Link output
Use this 6.35mm output to link the signal to another amplifier or PAJ-12A.
7) Fuse
8) AC power
Use an IEC (kettle) cable to connect the amplifier to a wall power
outlet
9) On / Off Power Switch
Press to power on / off the speaker box
10) Overload / Peak Indicator
11) Power Indicator
Amplifier
Input Power
Input Sensitivity
Dimensions Weight
Woofer
Impedance Sensitivity
Frequency response
Power output
Diameter
Coil diameter
Magnet
Tweeter
Impedance Sensitivity
Frequency response
Power output
Diameter
Coil diameter
Magnet
PAJ-12A
240V~ 50-60Hz
Line: 80mv Mic: 5mV
580x375x370mm 18.96kg
4 ohms
102 dB/m/w
50Hz - 3.5kHz
120W RMS / 220W MAX
12"
2 5".
1.400kg
8 ohms
106dB/m/w
3kHz a 20kHz
30W RMS / 50W MAX
4,5"
1.3"
0.368kg
Product design and specifications are subject to change without
notice.
Tabla de contenidos
Otros manuales de Oradores de Qtx
Qtx
Qtx DELTA-50 Manual de usuario
Qtx
Qtx QR10PABT Manual de usuario
Qtx
Qtx PAV8-UHF Manual de usuario
Qtx
Qtx QR8K Manual de usuario
Qtx
Qtx BUSKER-10U Manual de usuario
Qtx
Qtx QR10PA Manual de usuario
Qtx
Qtx QR12PA Manual de usuario
Qtx
Qtx QR12PA Manual de usuario
Qtx
Qtx QT Series Manual de usuario
Qtx
Qtx 100.615UK Manual de usuario
Qtx
Qtx BUSKER-12 Manual de usuario
Qtx
Qtx QR10PA Manual de usuario
Qtx
Qtx QR8PA-BT Manual de usuario
Qtx
Qtx QR10PA Manual de usuario
Qtx
Qtx PartyPod Manual de usuario
Qtx
Qtx QS Series Manual de usuario
Qtx
Qtx QX15PA Plus Manual de usuario
Qtx
Qtx QX12A Manual de usuario
Qtx
Qtx QX8BT Manual de usuario
Qtx
Qtx QX12AV Manual de usuario
