QPS Que! Manual de usuario
QPS TECHNICAL SUPPORT
Our Customer Support staff are ready to assist you with any problem you may have with
your QPS Product.
There are many ways to contact QPS Technical Support.
E-Mail: [email protected]
World Wide Web: http://www.qps-inc.com
Technical Support: (714) 692-3588
Technical FAX: (714) 692-5516
COPYRIGHT STATEMENT
Copyright © 1998-2001 QPS Professional Solutions. All rights reserved. No part of this
publication may be reproduced or transmitted in any form by any means for any purpose
without the prior written permission of QPS Inc.
Windows is a trademark of Microsoft Corporation.
Apple, Mac OS are trademarks of Apple Computer Inc.
All other brand and product names are trademarks or
registered trademarks of their respective owners.
COPYRIGHT PROTECTION NOTICE
Replicating copyrighted material without the permission of the publisher may be unlawful.
QPS does not condone, support, or encourage the violation of copyright laws. Please obtain
proper authorization prior to replicating copyright protected material.
Note: Please refer to Que! Internal DVDBurner Installation Manual CD for complete installation version.
TECHNICAL SUPPORT
1
CONGRATULATIONS
THANK YOU
for Choosing QPS!
Congratulations on your purchase of the
Que! Internal DVDBurner Drive. In this manual,
you’ll find information designed to help you
understand the capability of your new drive
as well as a step-by-step explanation of how
to install your hardware and software.
GETTING STARTED
WHAT YOU SHOULD HAVE!
• What’s in the Package
Refer to the provided package list on the following page and verify that you have received
all of the appropriate parts.
Okay, if all the right parts were in the package, then you just need to make sure your
system will support the Que! DVDBurner Drive. Here's what you'll need.
Minimum System Requirements for PC
•Pentium III 700MHz processor (1.1 GHz processor required for real-time performance)
•MS Windows 98SE, ME, 2000, NT 4.0 SP5
• 128 MB RAM(256 MB recommended)
• CD-ROM drive for software install
•300 MB free hard disk space for software installation(5 GB required for DVD-R
mastering) for software install
•AGP Video Card with 8MB Video RAM .
Note: DVD set top players must be Generation 2 or later (circa 1992 or later). refer to
your DVD player owner's manual for verification of compatibility with General
DVD-R media.
Note: Please refer to Que! Internal DVDBurner Installation Manual CD for complete installation version.
2
3
PACKAGE LIST
Drive
Software Disc
Media
Quick Start Guide
Ribbon Cable:
40 pin IDE cable
Audio Cable
IDE INSTALLATION
The figure below shows the front panel controls and indicator for the Que! Drive for
IDE/ATAPI.
Note: The front panel may vary slightly.
Note: The location of jumpers may vary from one model to another.
Note: Please refer to Que! DVDBurner Installation Manual CD for complete installation version.
4
IDE INSTALLATION
Step 1. Unpack the drive accessory box. The accessory box should have a disc with
the included software, a QPS DVD-R disc, an audio cable, an IDE ribbon cable
and mounting screws.
Step 2. Shut down and turn off your computer.
Step 3. Remove the cover from your computer (please refer to your PC owners
manual for the proper way to do this).
Step 4. Remove the cover plate from an available 5.25" drive bay or remove the drive
that you want to replace. Set aside any mounting hardware for later use. If
your system requires mounting rails go to step 5 otherwise proceed to Step 6.
Step 5. Attach the drive mounting hardware to the Que! Drive using M3 (ISO Metric
Screw Threads). Reference the figure below.
Caution: Using the incorrect screw thread or length will damage the drive and void
your warranty. Consult your computer manufacturer for the correct mounting
hardware(rails) and screws, rails may not be needed.
Note: Please refer to Que! DVDBurner Installation Manual CD for complete installation version. 5
IDE INSTALLATION
Step 6. Set the Master/Slave jumper as appropriate for your system. When connecting
a second IDE device to thesame IDE interface connector cable you should
designate the first device as the Master and the second device as the Slave.
This is done by placing the jumpers over the corresponding pins on the back
of your DVDBurner drive.
Note: The location of jumpers may vary from one model to another.
Note: Please refer to Que! DVDBurner Installation Manual CD for complete installation version.
6
IDE INSTALLATION
Step 7. Insert your Que! Drive into the available bay.
Note: The Que! Drive must be mounted in a HORIZONTAL position.
Step 8. Put the mounting screws in just tight enough to hold the drive in the system
but loose enough to be able to move the drive back and forth.
Step 9. Insert the power connection to the back of the Que! Drive. Then plug in the
IDE ribbon cable to the IDE interface on the back of the drive. Please be sure
that the side of the IDE ribbon cable with the red stripe goes toward pin 1 on
the back of the drive. Pin 1 is always marked on the back of internal drives.
Note: Please refer to Que! Internal DVDBurner
Installation Manual CD for complete installation
version. 7
IDE INSTALLATION
Note: A fan may or may not be present
on your drive. Individual drive
specifications may differ from that
which is show here and may change
without notice.
Step 10. If you wish to have the audio output of your Que! Drive connected to your
sound card, simply connect one end of the audio cable provided with the
Que! Drive kit to the audio out connector on the back of the Que! Drive and
the other end to the audio input connector on the sound card. If the audio
cable is not keyed make sure that the red wire lines up with the pin labeled
"R". If you do not see a connector that matches the audio cable that has been
provided in this kit, you may need to purchase a special connector for your
sound card.
Step 11. Line up the front bezel of your QPS drive with the front panel of your system
and then tighten the mounting screws.
Step 12. Replace your computer’s cover.
Step 13. Power up your computer.
Step 14. Proceed to the software installation section.
Note: Please refer to Que! Internal DVDBurner Installation Manual CD for complete installation version.
8
IDE INSTALLATION
Otros manuales para Que!
4
Tabla de contenidos
