Qeedji TAB10s Manual de usuario
User manual 001C
TAB10s
9.10.10
TAB10s
8:30
2
Legal noce
TAB10s 9.10.10 (001C_en)
© 2020 Qeedji
Rights and Responsibilies
All rights reserved. No part of this manual may be reproduced in any form or by any means whatsoever. or by any means whatsoever without the wrien permission of the
publisher. The products and services menoned herein may be trademarks and/or service marks of the publisher. or trademarks of their respecve owners. The publisher and the
author do not claim any rights to these Marks.
Although every precauon has been taken in the preparaon of this document, the publisher and the author assume no liability for errors or omissions, or for damages resulng
from the use of the informaon contained in this document or the use of programs and source code that can go with it. Under no circumstances can the publisher and the author be
held responsible for any loss of profits or any other commercial prejudice caused or alleged to have been caused directly or indirectly by this document.
Product informaon
Product design and specificaons are subject to change at any me and `Qeedji` reserves the right to modify them without noce. This includes the hardware, the embedded
soware and this manual, which should be considered as a general guide to the product. The accessories supplied with the product may differ slightly from those described in this
manual, depending on the developments of the various suppliers.
Precauons for use
Please read and heed the following warnings before turning on the power: - installaon and maintenance must be carried out by professionals. - do not use the device near water. -
do not place anything on top of the device, including liquids (beverages) or flammable materials (fabrics, paper). - do not expose the device to direct sunlight, near a heat source, or
in a place suscepble to dust, vibraon or shock.
Warranty clauses
The `Qeedji` device is guaranteed against material and manufacturing defects for a certain duraon. Check the device warranty duraon value at the end of the document. These
warranty condions do not apply if the failure is the result of improper use of the device, inappropriate maintenance, unauthorized modificaon, operaon in an unspecified
environment (see operang precauons at the beginning of the manual) or if the device has been damaged by shock or fall, incorrect operaon, improper connecon, lightning,
insufficient protecon against heat, humidity or frost.
WEEE Direcve
This symbol means that your appliance at the end of its service life must not be disposed of with household waste, but must be taken to a collecon point for waste electrical and
electronic equipment or returned to your dealer. Your acon will protect the environment. In this context, a collecon and recycling system has been set up by the European Union
3
1.1
1.2
1.3
1.3.1
1.3.2
1.3.3
1.4
1.5
1.6
1.7
1.8
2.1
2.2
2.3
2.3.1
2.3.2
2.3.3
2.4
3.1
3.2
3.3
3.4
4.1
5.1
5.2
5.3
Table of contents
1 - Descripon and installaon
Introducon
Labelling
Product faces
Device dimensions
Device fixture
Drilling paern
Power supply
Device start-up step
Surround light behaviour at power-up
Connectors pin-out
Procedure to access to the back connectors
2 - Configuraon
Configuraon with the sengs applicaon
APK
Qeedji System service
APK installaon or upgrade
Configuraon by script
AOSP firmware upgrade
Factory recovery
3 - Technical informaon
Technical specificaons
Built-in RFID reader
Antenna return loss
Conformies
4 - Contacts
Contacts
5 - Appendix
Appendix 1: Qualified references for third party hub
Appendix 2: ISO image burning with BalenaEtcher
Appendix 3: TFTP and DHCP server configuraon
4
1.1 Introducon
This manual explains how to install and configure your device TAB10s. It explains also how to install a third party APK or and realize a OS upgrade.
Content of the package
Items Descripon Quanty
Device TAB10s with AOSP embedded 1
Mounng bracket Bracket for wall mounng 1
Drilling paern leaflet Drilling paern 1
Screws M2 x 35mm sloed countersunk screw (DIN 963) - a2 stainless steel 2
Adhesive 3M double sided tape 4905, material: VHB, W x H x D: 65 mm x 19 mm x 0.5 mm 2
Recommendaons and warnings
This device is designed to be used indoor.
The device is delivered without a power supply unit. Depending on your needs, Qeedji is making recommendaon for suitable power supply references in the chapter § Power
supply.
◬
Before supply the TAB10s with the USB connector of your computer, check with your computer's manufacturer that the USB connectors is suitable to deliver a
sufficient power supply.
◬
In case you had to remove the micro SD card, ensure first that the TAB10s is powered off before removing or inserng the micro SD card. In case of bad handling, the
micro SD card replacement would not be covered by the warranty.
This device is a Class A device. In a residenal environment, this device may cause radio interference. In this case, the user is asked to take appropriate measures.
5
1.2 Labelling
☛ The serial number of the device can be requested in case of technical support.
These are the labels stuck on the case and the cardbox. They are showing informaon embedded also in the QR code:
the device model,
the product serial number (PSN),
the MAC addresses.
They are showing also:
the power supply characteriscs,
the manufacturer Web site,
the conformity logo.
☛ FCC cerficaon in pending.
This is the label stuck also on the cardbox. It is showing:
the device model,
the QR code embedding the product serial number (PSN),
the manufacturer Web site.
Some addional labels may be present in case of built-in opons.
MAC WLAN: 00-1C-E6-02-4E-90
5VInput:
Model: TAB10s
5A rue Pierre Joseph Colin
35000 Rennes, FR
PSN013520-00011 CD3
www.qeedji.tech
2A
MAC WPAN: 1B-1E-A2-09-DA-B4
Contains IC: TBD
Contains FCC ID: TBD
3 7 0 0 5 6 8 1 0 7 4 6 9
TAB10s
www.qeedji.tech
6
1.3 Product faces
Device's front face
1 Touch screen,
2 Camera,
3 Built-in NFC/RFID sensor,
4 Presence sensor.
Device's up face
10 Surround light,
11 Mono speaker,
12 Hardware reset,
13 Built-in microphone n°1,
18 Built-in microphone n°2,
14 Heat pipe.
Do not cover the top of the heat pipe which is designed to evacuate naturally the heat of the device when it is running.
Device's boom face
10 Surround light,
15 USB-C connector,
16 Mounng bracket orifice/screw n°1,
17 Mounng bracket orifice/screw n°2,
20 USB-C locking orifice n°1,
21 USB-C locking orifice n°2.
1
2
3
4
10
11
12
13
18
14
10
15
16
17
20
21
8
1.3.1 Device dimensions
9
1.3.2 Device fixture
The TAB10s can be hung on the wall using a mounng bracket (supporng or not the POGO interface).
◬
The TAB10s is designed to be installed horizontally (landscape mode only).
Before installing, check that the posion of the microphone DIP switch and the camera DIP switch is matching the customer needs.
4 mm4 mm
84.6 mm84.6 mm
78.3 mm78.3 mm
74.3 mm74.3 mm
Wall with pierceable
4 mm4 mm
Glass wall
material
Dowel Double sided tape
M2x35 screws
10
1.3.3 Drilling paern
In case you want to hang the TAB10s device on the wall, you can do it using the provided mounng bracket.
Follow the drilling paern to install it.
This mounng bracket can be fixed using screws (recommended for walls with pierceable material).
☛ The screws and dowels required to fix the mounng bracket on the wall are not provided with the product. They can depend on the wall material.
Adhesive paern
If it is not possible to fix the device with screws, for example when needing to be fixed on a glass wall, you can use the provided double-sided tapes.
⚠
Clean carefully the surface before stucking the tapes.
Casing center
Screws (2x)
6 mm ≤ head Ø ≤ 9.5 mm
Ø ≤ 4 mm
30 mm
255 mm
178.5 mm
30 mm
69.5 mm
h ≤ 4 mm
19.75 mm 89.25 mm
9.5 mm
32.5 mm
36.5 mm
41.7 mm
37.7 mm
Casing
center
255 mm
178.5 mm
76.3 mm
double-sided
adhesives (2x)
27.7 mm
85 mm
85 mm
65 mm
19 mm
74.3 mm
84.6 mm
Otros manuales para TAB10s
4
Tabla de contenidos
Otros manuales de Tableta de Qeedji
